Matrix 7" User manual

7” TFT LCD TeLevision
oWneR’s MAnUAL

CONTENTS
CHAPTER 1: IMPORTANT INFORMATION & SAFETY PRECAUTIONS PAGES
1.1 Important Information 01
1.2 Important Safety Precautions 02
CHAPTER 2: GETTING STARTED
2.1 Package Contents 04
2.2 Connection 04
CHAPTER 3: DISPLAY AND CONTROL OVERVIEW
3.1 Controls 05
CHAPTER 4: PROGRAMMING THE TELEVISION & ADJUSTING THE SETTINGS
4.1 Programming the Television 06
4.2 Picture Settings 07
4.3 Aspect Ratio 07
4.4 Cable Broadcasting System 07
4.5 Channel Setup 08
4.6 Sleep Timer 08
CHAPTER 5: BRACKET ASSEMBLY & INSTALLATION FOR
CYCLES, ELLIPTICALS, ASCENT TRAINER AND STEPPER
5.1 Required Fasteners & Assembly Tools 09
5.2 Bracket Assembly 09
CHAPTER 6: INSTALLATION ON THE T3x / T3xi TREADMILL
6.1 Required Fasteners & Assembly Tools 11
6.2 7” TV T3x/T3xi Treadmill Installation 11
CHAPTER 7: INSTALLATION ON THE T5x TREADMILL
7.1 Required Fasteners & Assembly Tools 13
7.2 7” TV T5x Treadmill Installation 13

1 MATRIX FITNESS SYSTEMS ENTERTAINMENT
7” TFT LIQUID CRYSTAL TELEVISION OPERATION MANUAL
CHAPTER 1 : IMPORTANT INFORMATION & SAFETY PRECAUTIONS
Thank you for purchasing the Matrix Liquid Crystal Television. To ensure safety and many years of trouble free
operation of your product, please read the important safety precautions carefully before using this product.
1.1 IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
FEDERAL COMMUNICATIONS COMMISSION INFORMATION (FCC):
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separtion between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
[ USA ONLY ]
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
This product utilizes tin-lead solder containing a small amount of mercury. Disposal of these materials
may be regulated due to environmental considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries Alliance. (www.eia.org)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
THE LIGHTING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN
EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER
TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE”
WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO
PERSONS.
THE EXCLAMATION POINT WITHIN A TRIANGLE IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING
AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERA-
TURE ACCOMPANYING THE PRODUCT.

MATRIX FITNESS SYSTEMS ENTERTAINMENT 2
1.2 IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong
the service life of your Liquid Crystal Television, please read the following precautions carefully before using the
product.
Read instructions - All safety and operating instructions must be read and understood before the product is
operated.
Keep the manual in a safe place - These safety and operating instructions must be kept in a safe place for future
reference.
Observe warning - All warnings on the product and in the instructions must be observed closely.
Following instructions - All operating instructions must be followed.
Attachments - Do not use attachments not recommended by the manufacturer. Use of inadequate attachments
can result in accidents.
Power source - This product must operate on a power source specified on the specification label. If you are not
sure of the type of power supply used in your facility, consult your dealer or local power company. For units
designed to operate on batteries or another power source, refer to the operating instructions.
Power cord protection - The power cords must be routed properly to prevent people from stepping on them or
objects from resting on them. Check the cords at the plugs and product.
AC power adapter - If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from
Matrix customer service or your dealer.
Overloading - Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
Entering of objects and liquids - Never insert an object into the product through vents or openings. High voltage
flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same
reason, do not spill water or liquid on the product.
Servicing - DO NOT attempt to service the product yourself. Removing covers can expose you to high voltage and
other dangerous conditions. Contact Matrix customer service to perform service on this product.
Repair - If any of the following conditions occur, unplug the power cord from the AC outlet, and request a
qualified service person to perform repairs
a. When the power cord or plug is damaged
b. When a liquid is spilled on the product or when objects have fallen into the product
c. When the product has been exposed to rain or water
d. When the product does not operate properly as described in the operating instructions
DO NOT touch the controls other than those described in the operating instructions. Improper adjustment of
controls not described in the instructions can cause damage, which often requires extensive adjustment work
by qualified technician
e. When the product has been dropped or damaged
f. When the product displays an abnormal condition, any noticeable abnormality in the product indicates that
the product needs servicing
•
•
•
•
•
•
•
•
•
•
•
•

1.2 IMPORTANT SAFETY PRECAUTIONS [ Continued ]
3 MATRIX FITNESS SYSTEMS ENTERTAINMENT
Replacement parts - In case the product needs replacement parts, make sure that the service person uses
replacement parts specified by the manufacturer. Use of unauthorized parts can result in fire, electric shock
and/or other danger, and could void the product warranty.
Safety checks - Upon completion of service or repair work, request the service technician to perform safety
checks to ensure that the product is in proper operating condition.
Polarization - This AC adapter may be equipped with a polarized alternating current line plug (a plug having one
blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Cleaning - Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean
the product. Do not use liquid cleaners or aerosol cleaners.
Water and moisture - Do not use the product near water, such as a bathtub, washbasin, kitchen sink, laundry tub
or swimming pool.
Ventilation - The vents and other openings in the case are designed for ventilation. Do not cover or block these
vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product.
This product is not designed for built-in installation; do not place the product in an enclosed place, unless proper
ventilation is provided or the manufacturer’s instructions are followed.
Caution -The Iiquid crystal panel used in this product is made of glass. Therefore, it can break when the product
is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the liquid crystal
panel breaks.
Heat sources - Keep the product away from heat sources such as radiators, heaters, and other heat-generating
products (including amplifiers).
Lightning - For added protection for this television during a lightning storm, or when it is left unattended and
unused for long period or time, unplug it from wall outlet and disconnect the antenna. This will prevent damage
to the equipment due to lightning and power-line surges.
Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.
To prevent fire - Never place any type of candle or naked flames on the top or near the TV set.
To prevent fire or shock hazard - Do not expose this product to dripping or splashing. No objects filled with
liquids, such as vases, should be placed on the product.
•
•
•
•
•
•
•
•
•
•
•
•

MATRIX FITNESS SYSTEMS ENTERTAINMENT 4
CHAPTER 2 : GETTING STARTED
Read the entire operation manual before setting up the 7” TFT LCD Television.
2.1 PACKAGE CONTENTS
Make sure the package includes a TV monitor and the accessories shown below.
If items are missing, please call customer service at 866.693.4863.
7” TFT LCD TV AC POWER ADAPTER OPERATION MANUAL
2.2 CONNECTION
TERMINAL DIAGRAM
ANTENNA OR CABLE TV (CaTV) CONNECTION:
Connect your “F” type cable TV or antenna coaxial signal cable to the provided antenna adapter.
POWER CONNECTION:
Connect the small end of the power adapter to the power input on the rear of the TV. Connect the AC power cord
to a suitable AC power wall socket. The AC power adapter enclosed in this product is rated for 100-240v 50/60
Hz electrical systems.
VOLUME CHANNEL
1
RESET ENTER
2 3
4 5 6
7 8 9
0
LAST
™
7”TV TFT LCD TELEVISIOIN
OWNERS MANUAL
Strong •Smart •Beautiful
Strong •Smart •Beautiful
MATRIX FITNESS SYSTEMS CORP.
1610 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
TO L L FR E E 86 6 . 6 9 3 . 4 8 6 3 www.matrixfitness.com FAX [phone]
PAR T # 000 0 0 0 - B
REV. 01
POWER
INPUT ANTENNA

CHAPTER 3 : DISPLAY AND CONTROL OVERVIEW
3.1 CONTROLS
VOLUME CHANNEL
1
RESET ENTER
2 3
4 5 6
7 8 9
0
LAST
™
1
2
3 4
6
7
5
1POWER
Switch the television power ON or OFF
Select volume
2VOLUME
3RESET
Clears numeric keypad selections
Execute a command
4ENTER
RESET
ENTER
5CHANNEL
Select channel
Previous channel jump button
6LAST
7CHANNEL SELECTION NUMBER PAD
Set the television channel
LAST
1 2 3
5 MATRIX FITNESS SYSTEMS ENTERTAINMENT

CHAPTER 4 : PROGRAMMING THE TELEVISION & ADJUSTING THE SETTINGS
4.1 PROGRAMMING THE TELEVISION
In order for your 7” LCD TV to broadcast the channels provided by your cable provider, you will
need to program the TV to receive the channels.
STEP 1: Press and hold the volume Ç button and the channel p button until the menu screen
appears.
• Each menu heading is described below:
* To cycle through the options that are available under a selected menu heading, use the channel Çp
buttons. To adjust a particular option, highlight the option and adjust the value using the
volume Çp buttons. Press the “ENTER” button to advance to the next menu heading.
MATRIX FITNESS SYSTEMS ENTERTAINMENT 6
VOLUME CHANNEL
1
RESET ENTER
2 3
4 5 6
7 8 9
0
LAST
™
Picture Settings
Aspect Ratio
Cable Broadcasting System
Channel Setup
Sleep Timer

7 MATRIX FITNESS SYSTEMS ENTERTAINMENT
CHAPTER 4 : PROGRAMMING THE TELEVISION & ADJUSTING THE SETTINGS
STEP 2: Press the “ENTER” button to advance to the channel setup heading.
STEP 3: Using the channel Çp buttons, highlight the “CaTV” setting then press the volume p
button. This will program the TV to receive all channels available to your facility.
* If the cable provider in your area uses HRC or IRC channel frequencies, repeat steps 1-3, but
highlight “HRC” or “IRC” instead of “CaTV.”
4.2 PICTURE SETTINGS
STEP 1: Press and hold the volume Ç button and the channel p button until the menu screen
appears.
* Picture settings is the first menu heading and will be on screen when you enter the setup menu.
STEP 2: Cycle through to the field that you want to modify using the channel Çp buttons and
when that field is highlighted, use the volume Çp buttons to adjust the setting.
4.3 ASPECT RATIO
STEP 1: Press and hold the volume Ç button and the channel p button until the menu screen
appears.
STEP 2: Press the “ENTER” button to advance to the aspect ratio heading.
STEP 3: Cycle through to the field that you want to modify using the channel Çp buttons and
when that field is highlighted, use the volume Çp buttons to adjust the setting.
* Your 7” TV broadcasts in both 16:9 and 4:3 aspect ratio. Full is the 16:9 setting and zoom is 4:3.
4.4 CABLE BROADCASTING SYSTEM
STEP 1: Press and hold the volume Ç button and the channel p button until the menu screen
appears.
STEP 2: Press the “ENTER” button to advance to the cable broadcasting system heading.
STEP 3: Cycle through to the field that you want to modify using the channel Çp buttons and
when that field is highlighted use the volume Çp buttons to adjust the setting.
*This TV has a global tuner and will broadcast NTSC358, NTSC443, PALM, PALN, PAL60,
PAL443 and SECAM COLOR SYSTEMS.

MATRIX FITNESS SYSTEMS ENTERTAINMENT 8
CHAPTER 4 : PROGRAMMING THE TELEVISION & ADJUSTING THE SETTINGS
4.5 CHANNEL SETUP (SEE 4.1)
4.6 SLEEP TIMER
STEP 1: Press and hold the volume Ç button and the channel p button until the menu screen
appears.
STEP 2: Press the “ENTER” button to advance to the sleep timer heading.
STEP 3: Adjust the timer using the volume Çp buttons.
(The timer length can be set between 0-240 minutes)

CHAPTER 5 : BRACKET ASSEMBLY AND INSTALLATION FOR
CYCLES, ELLIPTICALS, ASCENT TRAINER AND STEPPER
5.1 REQUIRED FASTENERS & ASSEMBLY TOOLS
5.2 BRACKET ASSEMBLY
STEP 1
Assemble plate 1 and plate 2
to the main bracket using the
button head socket screw (L10),
flat washer (L09), and nut (L08)
as shown.
STEP 2
Install the power wire and
coaxial cable at the top of the
bracket to the TV.
STEP 3
Fasten the TV to the main
bracket using the button head
hex socket screw (Z05) as
shown
9 MATRIX FITNESS SYSTEMS ENTERTAINMENT
01 4mm ALLEN WRENCH
01 #2 PHILLIPS SCREW DRIVER
QTY SKETCH DESCRIPTION QTY PART # SKETCH DESCRIPTION
01 3mm ALLEN WRENCH
01 FLAT WRENCH (#10 & #13) 02 L08 NUT (M6x1.0)
02 L10 BUTTON HEAD SOCKET SCREW (M6x1.0x50L)
02 L09 FLAT WASHER (6.2x12.0x1.0)
04 Z04 PHILLIPS HEAD MACHINE SCREW (M4x0.7x12L)
04 Z05 BUTTON HEAD HEX SOCKET SCREW (M5x0.8x10L)
Z05 x4
L10 x2
L08 x2
L09 x2
7”TV
TOP
BOTTOM
PLATE 2
PLATE 1
MAIN BRACKET

Z04 x4
MATRIX FITNESS SYSTEMS ENTERTAINMENT 10
CHAPTER 5 : BRACKET ASSEMBLY AND INSTALLATION FOR
CYCLES, ELLIPTICALS, ASCENT TRAINER AND STEPPER
STEP 4
Remove the chrome bolts (Z51) from
the console mast badge and pull the
power wire and coaxial cable from
inside the mast.
STEP 5
Connect the power wire and coaxial
cable from inside the mast to the
power wire and coaxial cable in the
bracket.
STEP 6
Mount the bracket to the console mast
using the chrome bolts (Z51) that
held the console mast badge in place.
STEP 7
Assemble the TV back cover to the
mounting bracket using the phillips
head machine screw (Z04).
FINAL ASSEMBLY
Z51 x4
Z51 x4
Z51 x4

CHAPTER 6 : INSTALLATION ON THE T3x/T3xi TREADMILL
6.1 REQUIRED FASTENERS & ASSEMBLY TOOLS
6.2 7” TV T3x/T3xi TREADMILL INSTALLATION
STEP 1
Assemble the TV to the bracket
using the button head socket
screw (Z05). Insert the end cap
into the bracket as shown.
11 MATRIX FITNESS SYSTEMS ENTERTAINMENT
QTY SKETCH DESCRIPTION QTY PART # SKETCH DESCRIPTION
01 3mm ALLEN WRENCH
01 #2 PHILLIPS SCREW DRIVER 04 Z01 BUTTON HEAD SOCKET SCREW (M8x1.25x45L)
04 Z02 FLAT WASHER (8.4x15.5x2.0)
04 Z04 PHILLIPS HEAD MACHINE SCREW (M4x0.7x12L)
04 Z05 BUTTON HEAD SOCKET SCREW (M5x0.8x10L)
Z05 x4
7”TV
BRACKET
END CAP

Z04 x4
MATRIX FITNESS SYSTEMS ENTERTAINMENT 12
CHAPTER 6 : INSTALLATION ON THE T3x/T3xi TREADMILL
STEP 2
Remove the cover plate from
the console by removing the
machine screw. Pull the TV
power wire and coaxial cable
out of the console.
STEP 3
While holding the bracket, route
the coaxial cable and power
wire through the bracket as
shown. Fasten the bracket to
the console using the button
head socket screw (Z01) and
flat washer (Z02).
STEP 4
Assemble the TV back cover
to the mounting bracket using
the phillips head machine
screw (Z04).
FINAL ASSEMBLY
COVER PLATE
MACHINE SCREW
Z01 x4
Z02 x4

CHAPTER 7 : INSTALLATION ON T5x TREADMILL
7.1 REQUIRED FASTENERS & ASSEMBLY TOOLS
7.2 7” TV T5x TREADMILL INSTALLATION
STEP 1
Assemble the TV to the bracket
using the button head socket
screw (Z05). Insert the end cap
into the bracket as shown.
13 MATRIX FITNESS SYSTEMS ENTERTAINMENT
7”TV
Z05 x4
END CAP
BRACKE
T
QTY SKETCH DESCRIPTION QTY PART # SKETCH DESCRIPTION
01 3mm ALLEN WRENCH
01 #2 PHILLIPS SCREW DRIVER 04 Z01 BUTTON HEAD SOCKET SCREW (M5x0.8x45L)
04 Z03 FLAT WASHER (5.2x13.0x1.5)
04 Z04 PHILLIPS HEAD MACHINE SCREW (M4x0.7x12L)
04 Z05 BUTTON HEAD SOCKET SCREW (M5x0.8x10L)

Z04 x4
MATRIX FITNESS SYSTEMS ENTERTAINMENT 14
CHAPTER 7 : INSTALLATION ON T5x TREADMILL
STEP 2
Remove the plastic cover located on
the rear of the console. Pull the TV
power wire and coaxial cable from
inside the console.
STEP 3
While holding the bracket, route the
TV power wire and the coaxial cable
through the bracket. Assemble the
bracket to the console with the
button head socket screw (Z01) and
the flat washer (Z03).
STEP 4
Assemble the back cover to the
bracket using the phillips head
machine screw (Z04).
FINAL ASSEMBLY
PLASTIC COVER
Z01 x4
Z03 x4

MATRix FiTness sysTeMs CoRp.
1610 LANDMARK DRIVE COTTAGE GROVE WI 53527 USA
TOLL FREE 866.693.4863 www.matrixfitness.com FAX [phone]
pART # 059916-A
Rev. 01