MaxWest MX-HUB User manual








QuickStartGuide


Note:
ThisUserGuideprovidesthebasicoperationsoftheMX‐HUB.


























1. Menubutton
2. SignalandRoamingstatusicon
3. Networkmode
4. Wi‐Fisignalicon
5. Unreadmessageicon
6. Batteryicon
7. PowerButton
8. MicroUSB
9. Batterycover


Displaylayoutandicon


IconDescription

SignalandRoamingstatusicon


Networkmodeicon

Dataflowicon

Wi‐Fisignalandnumberofaccessusers

Thenumberofunreadmessages，maximumis
100

Batterycapacityicon,ifbatterycapacityis
lowerthan20%,thisiconisred.
NetworkName
Statistics,used/total
WPSstatusindicator


InstallSIMCardandBattery
1. PowerofftheMX‐HUB
2. Removethebackcoverandbattery

3. InserttheSIMcardintocardslotinthecorrectposition
4. Installbackcoverandbattery
Note：
DONOTremoveSIMcardwhenpoweredonasthismaydamagethecardandMX‐HUB
SettingupWi‐Ficonnectionorwiredconnection
1. Pressandholdthe“power”buttonfor3seconds untilthewelcomelogoisdisplayedonthe
LCD,andWi‐Fiison.
2. SetupWi‐Ficonnectionorwiredconnectionasbelow
3. MakesureMX‐HUBWi‐Fifunctionison
4. SelectStart>ControlPanel>NetworkConnections>WirelessNetworkConnection
5. Click“Viewavailablewirelessnetworks”toshowalistofavailableWi‐Finetworks.
6. Selectthewirelessnetworkconnectionwiththe“MX‐HUB‐XXXX”Wi‐Fi’sSSIDandclick
“Connect”.Ifthesecuritymechanismisapplied,youneedtoenterthecorrectnetworkkey.
TheSSIDandnetworkkeylabelisavailableatthebatteryremovaldivot.
Note:XXXXisthelast4digitsofMACaddress(Capitalornumber).MaxLength32bits.
HowtochangetheSSID&Password
1. Logintohttp://192.168.1.1orhttp://mifi.homeandenterthemanagementpage.
2. SelectSettings>Wireless>WLANSettings,thenyouwillsee“Wi‐FiName(SSID)”and
“Password”,Makesureyoudeletetheoldnameandpasswordandenterthenewnameand
passwordasyourequire.
3. Select“Apply”button,waitforthescreentodisplayprompting“Success”,andthenlogout.
4. WaitforthecomputerorlaptopscreentodisplaytheWi‐Fiicon.Thismeansthewireless
networkconnectionhasbeensuccessful.
ConnectingtotheInternet
IftheWi‐Fifunctionisturnedon,yourdeviceshouldconnecttotheinternetautomatically.
LoggingintotheDeviceManagementwebsite
1. Makesuretheend‐userdeviceisconnectedtotheMX‐HUB

2. Openthebrowser,andenterhttp://192.168.1.1orhttp://mifi.homeintheaddressbox.
3. Enterusernameandpassword,andclick“Login”.Theadministratorhastherighttocheck
andmodifyconfigurationpermission.
Note:Thedefaultusernameandpasswordisadmin.

ChargingyourMX‐HUB
1stmethod:Chargingbypoweradapter
1. Usecompatiblepoweradapter(5V,1000mA)
2. Poweradapterisaselectiveaccessory.
2ndmethod:Chargingbyconnectingtocomputerorlaptop.
PleaseusethepropercabletoconnecttheMiFitothecomputerorlaptop.
Note:IftheMX‐HUBhasn’tbeenusedforalongtime,pleasechargethebatterybeforeusing.

RestoreFactorySettings
IfyouareuncertainofwhichWi‐Fisettingsyouhaveconfiguredorchanged,youcanrestorethe
factorydefaultsthatcomewiththeMiFitoreconfigurethedeviceWi‐Fisettingbytwooptions:
1. LogintoDeviceManagementWebsitetorestoretofactorydefaultsettings.
2. Pressandhold“Reset”buttonfor5seconds,andMX‐HUBwillbeactivatedagainand
restoredtofactorysettings.
Note:Resetbuttonwilldeleteallthedevice’suser‐definedWi‐FisettingsandrestoreAdmin
settingandWi‐FiSettingtofactorydefault.

TroubleShooting:
IfyouarehavingtroublewithMX‐HUB,hereareafewthingsyoucandotogetittofunction
properly.
1. Logintothedevicemanagementwebsiteandclickthehelpicononthetoprightcornerfor
answerstofrequentlyaskedquestions.
2. IftheMX‐HUBisnotresponsive,rebootitbypressthe“Power”buttonforabout8seconds
3. Restorefactorysettings

Q&A
Q:WhatdoIdoifIseetheSSIDbutfailedtoconnect?
A:1Checkthepasswordyouenteredistherightone.
2CheckifWPSsecurityisenabledonyourPC?Ifso,checkthedevicetoseeifitisexpectinga
WPSactionfromyourPC.

Q:WhattodoifthereisNoservice?
A:Thepossiblereasonislistedasbellow:
1Unstablelocalsignal.
2Hardwareproblem
Youcantrythefollowingsolutions:
1Ifyouareinsideabuildingornearastructurethatmaybeblockingthesignal,changethe
positionorlocationofthedevice.Forexample,trymovingthedeviceclosetoawindow.
2Checkthehardwareoruseanotherdeviceandretry


Q:WhattodoifIforgotWi‐FiKey?
A:YoucanresetthedevicetofactorydefaultsbypressPowerkeyfor8seconds.

Q:Whattodoif“PINlock”or“PUKlock”?
A:TheSIMcardislocked.LogintotheWebpageandEnteryourPINcodeorPUKcodeyougot
fromtheoperator.
Note:IfyouenteredwrongPIN3times,thenPUKisneeded,andifthewrongPUK
entered10times,theSIMcardwillbelockedforever.


Q:Dataconnectionfailed.
A:Youhavenonetworkcoverage.Trymovinglocationuntilyougetgoodreception.

Q:Themodemcannotconnecttotheinternetwhenoverseas
A:Youdon’thaveinternationalroamingenabledonyourplan.Consultyourservice
providerbeforeyougooverseastoenableroaming.


Note:
1. Caution:Riskofexplosionifbatteryisreplacedwithanincorrectorunapprovedtype.Use
batteriesmustdisposeaccordingtothemanufacturer’sinstructions.
2. TheproductshallonlybeconnectedusingaUSBinterfaceofversionUSB2.0.
3. Adaptershallbeinstalledneartheequipmentandshallbeeasilyaccessible.
4. EUTmaximumoperatedtemperature45degreeCelsius.




















Warning
Anychangesormodificationsnotexpresslyapprovedbythepartyresponsiblefor
compliancecouldvoidtheuser’sauthoritytooperatetheequipment.
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothe
followingtwoconditions:
(1) thisdevicemaynotcauseharmfulinterference
(2) thisdevicemustacceptanyinterferencereceived,includinginterferencethat
maycauseundesiredoperation.
Note:Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfora
ClassBdigitaldevice,pursuanttopart15oftheFCCrules.Theselimitsare
designedtoprovidereasonableprotectionagainstharmfulinterferenceina
residentialinstallation.Thisequipmentgenerates,usesandcanradiateradio
frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,
maycauseharmfulinterferencetoradiocommunications.However,thereisno
guaranteethatinterferencewillnotoccurinaparticularinstallationIfthis
equipmentdoescauseharmfulinterferencetoradioortelevisionreception,which
canbedeterminedbyturningtheequipmentoffandon,theuserisencouragedto
trytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
‐Reorientorrelocatethereceivingantenna.
‐Increasetheseparationbetweentheequipmentandreceiver.
‐Connect the equipment into an outlet a circuit different from that to which the
receiverisconnected.
‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

SAR tests are conducted using standard operating positions accepted by the FCC
with the device transmitting at its highest certified power level in all tested
frequency bands, although the SAR is determined at the highest certified power
level, the actual SAR level of the device while operating can be well below the
maximum value,Before a new device is a available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the exposure limit
established by the FCC, tests for each device are performed in positions and
locations as required by the FCC.
For body worn operation, this model device has been tested and meets the FCC RF
exposure guidelines when used with an accessory designated for this product.or
when used with an accessory that Contains no metal and that positions the device
a minimum of 10 cm from the body.
Non-compliance with the above restrictions may result in violation of RF exposure
guidelines.