Maytag MVWC450XW1 User manual

TOP-LOADING
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
GUIDE D'UT[LISATION
ET D'ENTRETIEN DE
LA LAVEUSE HAUTE
EFFICAciT[_ A FAiBLE
CONSOMMATION D'EAU
AVEC CHARGEMENT PAR
LE DESSUS
Para una versi6n de estas instrucciones en espafiol, visite www.maytag.com
Table of Contents Table des mati6res
WASHER SAFETY ................................................................ 2
WHAT'S NEW UNDERTHE LID? ........................................ 3
CONTROL PANEL AND FEATURES ..................................... 4
CYCLE GUIDE ..................................................................... 6
USING YOUR WASHER ...................................................... 7
WASHER MAINTENANCE ...................................................... 10
TROUBLESHOOTING ............................................................. 12
wARRANTY ................................................................................ 17
ASSISTANCE OR SERvIcE ............................... BAcK cOvER
SI_CURITI _ DE LA LAvEUSE ............................................... 18
QUOI DE NEUF SOUS LE cOUvERcLE? .......................... 19
TABLEAU DE cOMMANDE ET
cARAcTI_RISTiQU ES........................................................ 20
GUIDE DE PROGRAMMES ............................................... 22
UTiLISATiON DE LA LAvEUSE ......................................... 24
ENTRETIEN DE LA LAvEUSE .................................................. 27
DEPANNAGE ............................................................................ 29
GARANTIE ................................................................................ 35
ASSISTANCE OU SERvIcE .............. cOUvERTURE ARRIERE
Designed to use only
HE High Efficiency detergents.
Consue pour ['uti[isation d'un
d6tergent haute efficacit6 seu[ement.
W10280550A
W10280551A -SP

WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injuryto persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. Ifthe hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach intothe washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where itwill be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user=repair instructionsthat you understand and
have the skills to carry out.
[] See "Electrical Requirements" located in the installation
instructions for grounding instructions.
this time. SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

WHATrS NEW UNDER THE HD?
Cleaning with Less Water
Traditional agitator-style
washing machine
Washer with low-water
washplate wash system
The most striking difference in your new washer is the low-water
washplate wash system. The washer automatically adjusts the
water level to the load size---no water level selector is needed.
When loading the washer with dirty laundry, fill it evenly around
the basket wall.
Automatic Load Size Sensing
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water [eve[ for
the load. This may take several minutes before water is added. YOu
will find a step-by-step description in the "Cycle Status Lights"
section.
As the washer dampens and moves the load, the [eve[ of the
clothes will settle in the basket. This is normal, and does not
indicate that more clothes should be added.
IMPORTANT: You will not see a washer basket full of water like
with your past agitator-style washer.
Choosing the Right Detergent
Use only High Efficiency detergents. The package will be
marked "HE" or "High Efficiency." I_ow-water washing creates
excessive sudsing with a regular non-HE detergent. Using regular
detergent will likely result in longer cycle times and reduced
rinsing performance. It may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer's instructions to determine the amount of detergent
to use.
Use only High Efficiency (HE) detergent.
Concentrated Cleaning
[.ow-water cleaning means concentrated cleaning. Rather than
diluting detergent as done in an agitator-style washer, this washer
delivers the detergent directly to the soils.
The washp[ate moves the load while water is added in small
amounts until the load is wet. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
Norma[ Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer. For
example, you may hear a clicking and hum at the beginning of
the cycle, as the lid lock goes through a self-test. There will be
different kinds of humming and whirring sounds as the washp[ate
moves the load. And sometimes, you may hear nothing at all, as
the washer determines the correct water [eve[ for your load or
allows time for clothes to soak.

CONTROL PANEL AND FEATURES
O CYCLE OPTIONS
The following options may be added to most cycle.
G
See "Cycle uide for additional details.
DEEPCLEAN
This option provides enhanced cleaning action for tough
stains. It wi[[ add additional agitation and soak time to the
cycle.
FABRIC SOFTENER ADDED
This option must be set to "Yes" if using fabric softener.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
TEMPERATURE
Temperature Control senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric and soils
being washed. For best results and following the garment [abe[
instructions, use the warmest wash water safe for your fabric.
• Warm and hot water wi[[ be cooler than what your previous
washer provided.
• Even in a cool water wash, some warm water may be added
to the washer to maintain a minimum temperature.
_[_ WASH CYCLE
Use the Wash Cycle to select available cycles on your washer.
Turn the knob to select a cycle for your laundry load. See
G
"Cycle uide for detailed descriptions.
OSTART/PAUSE/UNLOCK BUTTON
Pressto start the selected cycle; press again to pause the cycle
and unlock the lid.
NOTE: if the washer is spinning, it may take several minutes to
unlock the lid. Pressand hold 3 sec to cancel a cycle.
OCYCLE STATUS LIGHTS
sensing wash rinse spirt done Lid |ricked
The Cycle Status Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or pauses that are
different from traditional washers.
SENSING
sensing wash rinse spin done lid locked
When the START/Pause/Unlock button is pressed, the washer
wi[[ first perform a serf-test on the lid lock mechanism. You wi[[
hear a dick, the basket wi[[ make a slight turn, and the lid wi[[
unlock briefly before locking again.
Once the lid has locked the second time, the washer wi[[ use
short, slow spins to estimate the load size. These sensing spins
may take 2 to 3 minutes before water is added to the load and
you may hear the hum of these spins, if the sensing light is on,
then washer is working properly. The washer wi[[ then move
the load briefly, pause to allow water to soak in to the load,
and resume adding water. This process may repeat until the
correct amount of water has been added for the load. You may
also hear water flowing through the dispenser, adding detergent
to the load.
NOTE: Avoid opening lid during sensing. The sensing process
will start over when the washer is restarted. The sensing light
may also come on during the Wash portion of the cycle. This
is normal.
WASH
sensing wash rinse spia dane lid locked
Im--_Z:)-ID-Im--mB-ID
You will hear the washplate moving the load. Unlike traditional
washers, the load is not covered with water. Low-water
cleaning means concentrated cleaning. Rather than diluting
detergent as done in an agitator-style washer, this washer
delivers the detergent directly to the soils. The motor sounds
may change at different stages in the cycle. The wash time is
determined by the selected soil [eve[.
4

RINSE LID LOCKED
sessisg wash rinse spin done lid _ockod
YOu will hear sounds similar to the wash cycle as the washer
rinses and moves the load. Always select "Yes" for Fabric
softener to be added when using the Fabric Softener Added
option. Some cycles will use a spray rinse.
SPIN
ssssisg wash dsse spin dose Ed locked
The washer spins the load at increasing speeds for proper water
removal, based on the selected cycle and spin speed.
DONE
sensing wash risse spin dsss lidlochsd
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
sensing wash rinse spin done [idlocked
To allow for proper load sensing and spinning, the lid will
lock and the [_id Locked light will turn on. This light
indicates that the lid is locked and cannot be opened.
If you need to open the lid, press
START/Pause/Unlock. The lid will unlock
once the washer movement has stopped.
This may take several minutes if the load
was spinning at high speed. PressSTART/
Pause/Unlock again to resume the cycle.
Avoid opening the lid during sensing. The
start 1
,ause/un[ock [
sensing process will start over when the washer is restarted.

CYCLE GUIDE
For best fabric care, choose the cycle that best fits the load being washed.
Not a[[ cycles and options are available on a[[ models.
Heavily soiled fabrics
Sturdy fabrics, colorfast
items, towels, jeans
Large items such as
sheets, small comforters,
jackets
Cottons, linens, sheets, and
mixed garment loads
Light weight cotton and
cotton blends
No-iron fabrics, cottons,
perm press, synthetics
Large items such as sheets,
sleeping bags, small
comforters, jackets, and
small washable rugs
Machine-wash silks,
hand-washed fabrics
Swimsuits and items
requiring rinsing without
detergent
Dripping wet item or
hand-washed items
No clothes in washer
[Heavy Duty
Heavy
[Heavy Duty
Regular
Normal
Heavy
Normal
Regular
Normal
Light
Casual
Bulky
Delicate
Rinse&
Spin
Drain &
Spin
Clean
Washer
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Cold
N/A
Hot
Warm
Coo[
Cold
*All rinses are cold.
**Spin speed is integrated into the cycle and can not be selected.
High
High
High
High
High
Low
High
Low
High
High
High
Provides maximum wash time and action for tough stains
and soils. Use this cycle for heavily soiled or sturdy items.
Water-level sensing process may take longer for some items
than for others because they will absorb more water than
other fabric types.
Use this cycle for heavily soiled or sturdy items. Water-level
sensingprocess may take longer for some items than for
othersbecause they will absorb more water than other fabric
types. This cycle features a spray rinse.
Use this cycle for heavily soiled cottons and mixed fabric
loads. This cycle features a spray rinse.
Use this cycle for normally soiled cottons and mixed fabric
loads. This cycle features a spray rinse.
Use this cycle for light weight cottons that are lightly soiled.
This cycle features a spray rinse.
Use this cycle to wash loads of no-iron fabrics such as sport
shirts, blouses, casual business clothes, permanent press, and
blends.
Use this cycle to wash large items such as iackets and small
comforters. The washer will fill with enough water to wet
down the load before the wash portion of the cycle begins,
and uses a higher water level than other cycles. Do not tightly
pack basket.
Use this cycle to wash lightly soiled garments indicating
"Machine Washable Silks" or "Gentle" cycle on the care
label. Place small items in mesh garment bags before
washing. This cycle uses a higher, preset water level.
Combines a rinse and high speed spin for loads requiring
an additional rinse cycle or to complete a load after power
interruption. This cycle uses a higher, preset water level. Also
use for loads that require rinsing only.
This cycle uses a spin to shorten drying times for heavy fabrics
or special-care items washed by hand. Use this cycle to drain
washer after cancelling a cycle or completing a cycle after a
power failure.
Use once a month to keep the inside of the washer fresh
and dean. Higher water levels and bleach work together to
thoroughly clean the washer interior. Use hot water for best
results. J

USING YOUR WASHER
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. sortand prepare your laundry
• Empty pockets. Loose change, buttons, or any small object
can pass under the washplate and become trapped, causing
unexpected sounds.
Sort items by recommended cycle, water temperature, and
colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing, because
heat can set stains into fabric.
• Treat stains promptJy.
• Close zippers, fasten hooks,tie strings and sashes, and remove
non-washable trim and ornaments.
Mend rips and tears to avoid further damage to items during
washing.
Helpful Tips:
When washing water-proof or water-resistant items, load
evenly. See "Cycle Guide" for tips and more information on
using the Bulky cycle.
Use mesh garment bags to help avoid tangling when washing
delicate or small items.
Turn knits inside out to avoid pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up
lint from towels, rugs, and chenille fabrics.
Always read and follow fabric care label instructions to avoid
damage to your garments.
Add a measured amount of HE
detergent into the basket.
iMPORTANT: Use only High Efficiency detergents. The package
will be marked "HE" or "High Efficiency." Low-water washing
creates excessive sudsing with a regular non-H E detergent.
Using regular detergent will likely result in longer cycle
times and reduced rinsing performance. [t may also result in
component failures and noticeable mold or mildew. HE
detergents are made to produce the right amount of suds for the
best performance. Follow the manufacturer's instructions
to determine the amount of detergent to use.
Using Oxi or color-safe bleach:
[f using an Oxi or color-safe bleach laundry boost product, add
to the bottom of the washer basket before adding clothes.

Load garments in loose heaps evenly around basket waN. Do
not wrap large items such as sheets around the washp[ate; load
them in loose piles around the sides of the basket. Try mixing
different sized items to reduce tangNng.
IMPORTANT." Do not tightly pack or force items into washer.
items need to move freely. Tightly packing can lead to poor
cleaning performance, and may increase wrinkNng and tangNng.
to dispenser
Do not overfill, dilute, or use more than 1 cup (250 mL). Do not
use color-safe bleach or Oxi products in the same cycle with
Nquid chlorine bleach.
This washer has been designed to allow
the use of the Downy Ball ® to dispense
fabric softener in the rinse cycle. Pour a
measured amount of Downy ® liquid fabric softener into the
Downy Ball ®, pull the ring tightly to seal it, and place on top
of load. Always follow manufacturer's directions for correct
amount of fabric softener based on your load size. Then select
"Yes" Fabric Softener Added option. The Downy Ball ® will
automatically release the fabric softener during the rinse cycle.
For questions on using the Downy Ball ® call 1-800-688-7638 or
visit www.downy.com.
IMPORTANT: Fabric Softener Added option must be selected to
"Yes" to ensure proper distribution at correct time in cycle. Do
not overfill or dilute.
Adding Liquid Fabric Softener Manual[y to Wash Load
During the final rinse, wait until the washer has completed fining,
press the START/Pause/Unlock button to Pause the washer. Lift
the lid and add the measured recommended amount of liquid
fabric softener. Do not allow liquid fabric softener to spill, splash,
drip, or run into the basket or on load. Do not use more than the
recommended amount. Close the lid and press the START/Pause/
Unlock button again to start the washer.
IMPORTANT: Fabric Softener Added option must be selected to
"Yes" to ensure proper distribution of the fabric softener during
the rinse portion of the cycle.
delicate
Turn cycle knob to choose your wash cycle.

7. Select wash temperature
temperature
all c0[d rinses
cold
9. Press START/Pause/Unlock to begin
wash cycle
Once you select a cycle, select the desire wash temperature by
turning the Temperature knob to the desired setting.
Always read and follow fabric care [abe[ instructions to avoid
damage to your garments.
iiiHot
Some cold water is added to save
ii energy. This will be cooler than
Warm
Some cold water will be added, so
this will be cooler than what your
Whites and pastels
Durable garments
Bright colors
Moderate to light soils
Cool
Warm water is added to assist in Colors that bleed
Cold
iiiWarm water may be added to assist Dark colors that
in soil removal and to help dissolve b eed or fade
detergents. Light soils
Pressthe START/Pause/Unlock button to start the wash cycle.
When the cycle has finished, the DONE indicator will light.
Promptly remove garments after cycle has completed to avoid
odor, reduce wrinkling, and rusting of metal hooks, zippers,
and snaps.
Unlocking the lld to add garments:
If you needto open the lid to add 1 or 2 missed garments:
PressSTART/Pause/Unlock; the lid will unlock once the washer
movement has stopped. This may take several minutes if the
load was spinning at high speed. Then close lid and press
START/Pause/Unlock again to restart the cycle.
If lid is [eft open for more than 10 minutes the water will pump
out automatically.
8. Select cycle options, if desired
deepdean extrarinse
off on off on
If you would like to add a Deep Clean and/or Extra Rinse
option, turn the knob for that feature to ON.

WASH ER MA[ NTENANCE
rWATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the [abe[ with a permanent marker.
f NON-USE AND VACATION CARE
operate your washer only when you are home.
If moving, or not using your washer for a period of time,
fo[ low these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due
to water pressure surge.
CLEANING YOUR WASHER
Keep your washer as clean and fresh as your clothes. To keep
washer interior odor-free, follow this recommended monthly
cleaning procedure:
1. Make sure the washer is empty.
2. Using liquid chlorine bleach, add 1 cup (250 mL) to
liquid chlorine bleach dispenser.
IMPORTANT: Do not add detergent to CLEAN WASHER
cycle. Do not use more than recommended amount of bleach
to avoid damaging product over time.
3. Close washer lid.
4. Select CLEAN WASHER cycle.
5. Press START/Pause/Unlock. Water will pour into washer
for a moment and pause, lid will lock, unlock, then cycle
will continue.
NOTE: For best results, do not interrupt cycle. If cycle must
be interrupted, Press and Hold START/Pause/Unlock for three
seconds and run a RINSE & SPIN cycle to ensure cleaner or
bleach have been rinsed from washer.
Cleaning the bleach dispenser
Wipe the inside of the bleach dispenser with a dean, damp
cloth.
To clean exterior:
1. Use a soft, damp cloth or sponge to wipe up any spills.
2. Use all-purpose surface cleaner, if needed.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
fwi NTER STORAG E cARE
IMPORTANT: TO avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. [f storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets, disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE & SPIN cycle for about 30 seconds to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
10

TRANSPORTi NG YOU RWASH ER
1. Shut off both water faucets, Disconnect and drain water
inlet hoses,
2. [f washer wiJ[ be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain from drain system and drain any
remaining water into a pan or bucket, Disconnect drain
hose from back of washer,
4. Unplug power cord,
5. Place inlet hoses and drain hose inside washer basket,
6. Drape power cord over edge and into washer basket,
7. Place packing tray from original shipping materials
back inside washer, if you do not have packing tray,
place heavy blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in new
location,
REINSTAI.MNG/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage or
moving:
1. Refer to "installation instructions" to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses, Reconnect water inlet hoses,
Turn on both water faucets,
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. PJug in washer or reconnect power.
3. Run washer through BULKY cycle to clean washer and
remove antifreeze, if used. Use only HE High Efficiency
detergent. Use 1/2 the manufacturer's recommended
amount for a medium-size load.
11

TROU BLESH OOTi NG
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service caR.In U.S.A. http://www.maytag.com/help - In Canada www.maytag.ca
Check the following for
proper installation or
see "Using Your Washer"
section,
Feet may not be in contact with the
floor and locked.
Washer may not be level.
Load could be unbalanced.
Front and rear feet must be in firm contact with floor, and washer
must be [eve[ to operate properly, lam nuts must be tight against
the bottom of the cabinet, See "installation instructions",
Check floor for flexing or sagging. If flooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See "Level the Washer" in installation instructions,
Load dry items in loose heaps evenly around basket wall,
Adding wet items to washer or adding more water to basket could
unbalance washer,
Do not tightly pack. Avoid washing single items.
Use Bulky cycle for oversized, non-absorbent items such as
comforters or poly-filled jackets.
See "Cycle Guide" and "Using Y0ur Washer" in this Use and
Care Guide,
Clicking or metallic
noises
Gurgling or humming
Humming
Objects caught in washer
drain system.
Washer may be draining water,
Is the sensing light on?
Empty pockets before washing, Loose items such as coins could fall
between basket and tub or may block pump, It may be necessary to
ca[[ for service to remove items,
It is normal to hear metal items on clothing such asmetal snaps,
buckles, or zippers touch against the stainless steel basket.
It is normal to hear the pump making a continuous humming sound
with periodic gurgling or surging as final amounts of water are
removed during the spin/drain cycles,
You may hear the hum of the sensing spins after you have started the
washers, This is normal Sensing spins will take several minutes before
water is added to the washer,
Check the following for
proper installation: Washer not level.
Fill hoses not attached tightly.
Fill hose washers.
Drain hose connection.
Check household plumbing for leaks
or clogged sink or drain.
Washer not loaded as
recommended.
Water may splash off basket if washer is not level,
Check that load is not unbalanced or tightly packed.
Tighten filllhose connection.
Are all four fill hose flat washers properly seated?
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub,
Do not place tape over drain opening.
Water can backup out of a clogged sink or drainpipe, Check all
household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets,)
Unbalanced loading can cause basket to be out of alignment and
cause water to splash off tub, See "Using Your Washer" for loading
instructions,
Not enough water
in washer Load not completely covered in water. This is normal operation for an HE low-water washer, The load will
not be completely underwater. The washer senses load sizes and adds
correct amount of water for optimal cleaning. See "What's New under
the Lid."
IMPOI_TANT: Do not add more water to washer. J
12

TROU BLESH OOT[ NG
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
fFirst try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) "N
to possibly avoid the cost of a service ca[[...In U.S.A. htt)://www.maytag.com/he[p - In Canada www.maytag.ca
Washer won't run or fill,
washer stops working Check for proper water supply.
Check proper electdca[ supply.
Normal washer operation.
Washer may be tightly packed.
Not using HE detergent or using too
much HE detergent.
Solution
Both hoses must be attached and have water flowing to inlet valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hosesp which can restrict water flow.
Plug power cord into a grounded 2. prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle. Do not
interrupt cycle.
Washer may be stopped to reduce suds.
The washer senses the dry load with short spins that may take 2 to
3 minutes before water is added.
Remove several items, rearrange load evenly in basket and add
detergent. Close lid and press START/Pause/Unlock.
Do not add more than 1 or 2 additional items after cycle has started
to avoid tightly packing or unbalancing.
Do not add more water to the washer.
Only use HE detergent. Suds from regular detergents can slow or
stop the washer. Always measure detergent and follow
detergent directions based on your load requirements.
To remove suds, cancel cycle. Select RINSE & SPIN. Press STAR]-/
PauseTUnlock. Do not add more detergent. J
13

TROU BLESH OOT[ NG
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service ca[[...In U.S.A. htta://www.maytag.com/he[p - In Canada www.maytag.ca
if you experlence
Washer not draining/
spinning, loads are
still wet
Dry spots on load
after cycle
Incorrect or wrong wash
or rinse
temperatures
Load not rinsed
Empty pockets and use garment bags for
small items.
Using a cycle with a low spin speed.
The washer may be tightly packed or
unbalanced.
Check plumbing for correct
drain hose installation. Drain hose
extends into standpipe farther than
4.5" (114 mm).
Wrong or too much detergent
causing suds to slow or stop draining
and spinning?
High speed spins extract more
moisture than traditional top-load
washers.
Check for proper water supply.
Energy saving controlled
wash temperatures.
Check for proper water supply.
Not using HE detergent or using too
much H E detergent.
Washer not loaded as recommended.
Small items may have been caught in pump or between basket
and tub, which can slow draining.
Cycles with lower spin speeds remove less water than cycles with
high spin speeds. Use the recommended cycle/speed spin for your
garment. To remove extra water in the load, select
DRAIN & SPIN. Load may need to be rearranged to allow even
distribution of the load in the basket.
Tightly packing or unbalanced loads will not allow the washer to
spin correctly, leaving the load wetter than normal. See "Using
Your Washer" for loading recommendations.
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening. Lower drain hose if the end is higher than 96" (2.4 m)
above the floor. Remove any clogs from drain hose.
Use only HE detergent. Always measure and follow detergent
directions for your load. To remove extra suds, select RINSE &
SPIN. Do not add detergent.
The high spin speeds combined with air flow during the final spin
can cause items near the top of the load to develop dry spots
during the final spin. This is normal.
Are hot and cold inlet hoses reversed?
Both hoses must be attached to both washer and faucet, and have
both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star washers use cooler wash and rinse water
temperatures than your previous washer. This includes
cooler hot and warm washes.
Are hot and cold inlet hoses reversed?
Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can keep washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions based
on load size and soil [eve[.
The washer is less efficient at rinsing when tightly packed.
Load garments in loose heaps evenly around the basket wall. The
washer will not rinse well if tightly packed. Load with dry items
only.
Use cycle designed for the fabdcs being washed.
Add only 1 or 2 garments after washer has started. J
14

TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service ca[[...In U.S.A. htt)://www.maytag.com/he[p - In Canada www.maytag.ca
if you experlence
Sand, pet hair, lint, etc.
on load after washing
Load is tangling
Not cleaning or
removing stains
incorrect dispenser
_,_peration
Heavy sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Washer not loaded as recommended.
Wash load not completely
covered in water.
Added more water to washer.
Washer not loaded as recommended.
Adding detergent on top of load.
Not washing like colors together.
Not using HE detergent or using too
much HE detergent.
Not using correct cycle for fabric type.
Not using dispenser or Downy BaIF_.
Not selecting "Yes" Fabric Softener
Added.
(]logged dispenser,
Possible Causes Solution
Add an Extra Rinse to the selected cycle.
See "Using Your Washer" section.
Select a cycle with a slower wash action and spin speed,
however items wi[[ be wetter than those using a higher
speed spin.
Load garments in loose heaps evenly around the basket wail.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Washer senses load size and adds correct amount of water, This is
normal and necessary for clothes to move.
Added water lifts the laundry off the washp[ate, resulting in less
effective cleaning.
Washer is less efficient at cleaning when tightly packed.
Load garments in loose heaps evenly around the basket wail.
Load with dry items only.
Add only 1 or 2 garments after washer has started.
Add detergent, oxi products and color safe bleach to the bottom of
the basket before adding the load items.
Wash like colors together and remove promptly after the cycle is
complete to avoid dye transfer.
The suds from regular detergent can keep washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow manufacturer's directions
based on load size and soil [eve[.
Use a higher soil [eve[ cycle option and warmer wash
temperature to improve cleaning.
Use Heavy Duty Heavy and Heavy Duty Regular cycle for tough
cleaning.
Use dispenser for chlorine bleach and Downy Bail °'_for fabric
softener to avoid staining.
Load dispenser before starting a cycle.
Add detergent to basket before adding load.
Always select "Yes" when adding fabric softener. Cycles that use
spray rinsing wi[[ add additional water for proper fabric softener
dispensing when "Yes" is selected.
Use only liquid chlorine bleach in the bleach dispenser,
.J
15

TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service ca[[...In U.S.A. htt)://www.maytag.com/he[p - In Canada www.maytag.ca
Fabric Damage
Odors
Sharp items were in pockets during
wash cycle.
Strings and straps could have tangJed.
items may have been damaged before
washing.
Fabric damage can occur if washer is
tightly packed.
Liquid ch[odne bJeach may have been
added incorrectly.
Garment care instructions may not have
been fo[ lowed.
Monthly maintenance not done as
recommended.
Using wrong or too much detergent.
Empty pockets, zip zippers, and snap or hook fasteners before
washing to avoid snagsand tears.
Tie a[[ strings and straps before starting wash load.
Mend rips and broken threads in seams before washing.
Load garments in loose heaps evenly around the basket wall.
Load with dry items only.
Use cycle designed for the fabrics being washed.
Add only I or 2 garments after washer is started.
Do not pour liquid ch[odne bleach directly onto load. Wipe up
bleach spills.
Undiluted bJeach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when loading
and unloading washer.
Always read and follow garment manufacturer's care [abe[
instructions,
Run the Clean Washer cycle monthly. See "Cleaning Your Washer"
in Washer Maintenance,
Unload washer as soon as cycle is complete.
Use onJy HE detergent. Be sure to measure correctly. AJways
follow the manufacturer's directions.
See "Cleaning your Washer" section. J
16

MAYTAG ®LAUNDRY WARRANTY
LIMITED WARRANTY
For one year frorn the date of purchase, when this rna'orj appliance is operated and rnaintained according to instructions attached to or
furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada I_P (hereafter "Maytag") will pay for factory
specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.
Service must be provided by a Maytag designated service company. YOUR SOLE AND EXCI_USIVE REMEDY UNDER THIS IJMITED
WARRANTY SHAI.L BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and
applies on[}/when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain
service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Rep[acernent parts or repair labor if this rnajor appliance is used for other than norrna[, sing[e-farni[y household use or when it is used in
a manner that is inconsistent to published User or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair
house fuses, or to correct house wMng or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance
with electrical or plumbing codes, or use of products not approved by Maytag.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results
from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Maytag servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with
Maytag published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be
easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPI.IED WARRANTIES, INCI_UDING ANY IMPHEI) WARRANTY OF MERCHANTABIIJTY OR IMPHEI) WARRANTY OF FITNESS FOR A
PARTICUI_AR PURPOSE, ARE IJMITED TO ONE YEAR OR THE SHORTEST PERIOD AH_OWED BY I.AW. Some states and provinces do not
allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOI_E AND EXCI_USIVE REMEDY UNDER THIS I.IMITEI) WARRANTY SHAH_ BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHAH_ NOT BE I.IABI_E FOR INCIDENTAl_ OR CONSEQUENTIAl_ DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the problem
after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling Maytag. In the
U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777. 6/08
Keep this book and your sales slip together for future reference.
You must provide proof of purchase or installation date for in-
warranty servmce.
Write down the following inforrnation about your rnajor appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
17

SECURiTE DE LA LAVEUSE
Votre s_curit_ et celle des autres est tr_s importante,
Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.
Assurez=vous de toujours lire tous les messages de securit6 et de vous y conformer.
Voici le symbole d'alerte de s6curit6.
Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de deces et de blessures graves
& vous eta d'autres.
Tousles messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de d6ces ou de blessure grave si
vous ne suivez pas imm_diatement [es instructions,
Risque possible de d_c_s ou de blessure grave
si vous ne suivez pas les instructions.
Tousles messages de s_curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de
blessure et ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE S['CURITI_
AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc electrique ou de blessures Iors de I'utilisation de la
laveuse, suivre les precautions fondamentales dont les suivantes :
[] Lire toutes les instructionsavant d'utiliser la laveuse.
[] Ne pas laver des articles qui ont et6 nettoy6s ou
lav6s avec de I'essence ou imbib6s d'essence,
solvants de nettoyage & sec, ou autres substances
inflammables ou explosives; ces substances
peuvent 6mettre des vapeurs susceptibles de
s'enflammer ou d'exploser.
[] Ne pas ajouter d'essence, solvant de nettoyage &
sec ou autre produit inflammable ou explosif dans
I'eau de lavage. Ces substances peuvent emettre
des vapeurs susceptibles de s'enfiammer ou
d'exploser.
[] Dans certaines conditions, de I'hydrog6ne gazeux
peut se former dans un circuit d'eau chaude qui n'a
pas 6t6 utilis6 pendant 2 semaines ou plus. LE GAZ
HYDROG#NE EST EXPLOSIBLE. Si le circuit d'eau
chaude n'a pas 6t6 utilis6 pendant une telle p6riode,
avant d'utiliser la laveuse, ouvrir tous les robinets
d'eau chaude et laisser I'eau s'6couler pendant
plusieurs minutes par chaque robinet. Ceci
permettra 1'6vacuation de I'hydrog6ne gazeux
accumul6. Comme ce gaz est inflammable, ne pas
fumer ou utiliser une flamme nue au cours de cette
p6riode.
[] Ne pas laisser des enfants jouer sur ou &I'interieur de la
laveuse. Bien surveiller les enfants Iorsque la laveuse est
utilisee & proximite d'enfants.
[] Avant de mettre la laveuse au rebut ou hors de service,
enlever la porte ou le couvercle.
[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de
la laveuse Iorsque le tambour, la cuve ou I'agitateur est en
mouvement.
[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle
serait exposee aux intemperies.
[] Ne pas modifier les organes de commande.
[] Ne pas reparer ou remplacer un composant quelconque de
la laveuse, ni entreprendre une operation de service, si ce
n'est specifiquement recommande dans ce manuel ou darts
un manuel d'instructions de reparations destine & I'utilisateur;
il est alors essentiel que la personne concernee comprenne
ces instructions et soit competente pour les executer.
[] Pour les instructionsde liaison &la terre, voir "Specifications
electriques" dans les instructionsd'installation.
CONSERVEZ CES INSTRUCTIONS
Avertissements de la proposition 65 de I'l_tat de Californie :
AVERTISSEMENT : Ce produit contient un produit chimique connu par I'€:tat de Californie pour _tre & I'origine de cancers.
AVERTISSEMENT : Ce produit contient un produit chimique connu par I'Etat de Californie pour _tre a I'origine de malformations
et autres deficiences de naissance.
18

QUOM DE NEUF SOUS LE COUVERCLE?
Nettoyer avec moins d'eau
I.aveuse traditionnelle de type
agitateur
I.aveuse _1faible consommation
d'eau avec impulseur
j_®®®
La nouveaut6 [a plus flagrante de cette nouvelle [aveuse est son
syst6me de lavage _ faible consommation d'eau avec impulseur.
[.a [aveuse ajuste automatiquement [e niveau d'eau en fonction de
la taille de la charge - nul besoin de s61ecteur de niveau d'eau.
I_orsque I'on charge la laveuse de linge sale, celui-ci dolt 6tre
r6parti uniform6ment [e long des patois du panier.
D6tection automatique de tail[e de charge
Une fois que ['on d6marre [e programme, [e couvercle se
verroui[[e et [a [aveuse entame un processus de d6tection pour
d6terminer [e niveau d'eau appropri6 h[a charge. Ce[a peut
prendre p[usieurs minutes avant que ['eau ne soit ajout6e. Voir
[a description pas-5-pas dans [a section "T6moins [umineux de
programme".
De ['eau est ajout6e _ [a charge pendant que [e panier tourne
[entement. Cette m6thode de [avage avec faib[e consommation
d'eau uti[ise moins d'eau et d'6nergie qu'une [aveuse
traditionne[[e de type agitateur.
A mesure que [a [aveuse imbibe et d6p[ace [a charge, [es
v6tements se tassent dans [e panier. Ceci est normal et ne
signifie pas que ['on doive rajouter des v6tements.
IMPORTANT : Vous ne verrez pas de panier de [aveuse remp[i
d'eau, comme avec votre pr6c6dente [aveuse de type agitateur.
Choix du d tergent appropri
Uti[iser uniquement des d6tergents Haute efficacit6. L'emba[[age
portera [a mention "HE" ou "High Efficiency" (haute efficacit6).
Un [avage avec faib[e consommation d'eau produit un exc6s
de mousse avec un d6tergent non HE ordinaire. I[ est probable
que ['uti[isation d'un d6tergent ordinaire pro[ongera [a dur6e
des programmes et r6duira [a performance de ring:age. Ceci peut
aussi entratner des d6fai[[ances des composants et une moisissure
perceptible. Les d6tergents HE sont congus pour produire [a
quantit6 de mousse ad6quate pour [e mei[[eur rendement. Suivre
[es recommandations du fabricant pour d6terminer [a quantit6 de
d6tergent _ uti[iser.
Udfiser uniquement un d(_tergent Haute efficacit6 (HE).
Nettoyage concentr
I.e syst6me de lavage _ faible consommation d'eau signifie un
[avage concentr6. Plut6t que de diluer du d6tergent comme dans
une [aveuse de type agitateur, cette [aveuse [ib?_re [e d6tergent
directement sur [es endroits souill6s.
Sons normaux pr visib[es
Au cours des diff6rents stades du programme de [avage, vous
entendrez peut-6tre des bruits que votre [aveuse pr6c6dente ne
produisait pas. Par exemp[e, vous entendrez peut-6tre un c[iquetis
au d6but du programme [orsque [e syst6me de verroui[[age du
couverc[e effectue un test automatique. On entendra diff6rents
bourdonnements et bruits de frottements rythmiques hmesure
que ['impu[seur d6p[ace [a charge. Parfois, i[ est possible que [a
[aveuse soit comp[6tement si[encieuse, [orsqu'e[[e d6termine [e
niveau d'eau ad6quat ou qu'e[[e [aisse tremper [es v6tements.
19

TABLEAU DE COMMANDE ET CARACTER[ST[QUES
A
U OPTIONS DE PROGRAMMES
II est possible d'ajouter les options suivantes _ [a plupart des
programmes. Voir "Guide de programmes" pour plus de
d6tai Is.
DEEPCLEAN (nettoyage en profondeur)
Cette option fournit une action de nettoyage amdlior6e pour
[estaches tenaces. Ceci pro[onge [a dur6e d'agitation et de
trempage du programme.
FABRIC SOFTENERADDED
(ajout d'assoupfissant pour tissu)
Le "Yes" de cette option doit 6tre s6[ectionn6 si ['on uti[ise
de ['assoup[issant pour tissu.
EXTRA RINSE (rinsage suppl_mentaire)
On peut utiliser cette option pour ajouter automatiquement
un second rin_age _ la plupart des programmes.
TEMPERATURE
La fonction de contr6le de temp(_rature d(_tecte et maintient
une temp6rature uniforme de I'eau en r6gulant le d6bit
d'arriv6e d'eau chaude et d'eau froide.
S61ectionner une temp6rature de lavage en fonction du type
de tissu et de salet6 _ laver. Pour des r6sultats optimaux,
suivre les instructions sur 1'6tiquette du v6tement et utiliser la
temp6rature d'eau de lavage la plus chaude possible qui reste
sans danger pour le tissu.
• Les temp6ratures de I'eau tilde et de I'eau chaude seront
inf6rieures _ celles de votre pr6c6dente laveuse.
• M6me avec un lavage _ I'eau froide, il est possible que de
I'eau tilde soit ajout6e _ la laveuse pour maintenir une
temp6rature minimale.
O WASH CYCLE (programme de lavage)
Uti[iser [e bouton de programme de [avage pour s6[ectionner
[es programmes disponib[es sur [a [aveuse. Tourner [e bouton
de programme pour s6[ectionner un programme correspondant
[a charge de [inge. Voir "Guide de programmes" pour des
descriptions d6tai[[6es.
O
O
BOUTON START/PAUSE/UNLOCK
(mise en marche/pause/d6verrouillage)
Appuyer sur ce bouton pour d6marrer [e programme
s6[ectionn6, puis appuyer de nouveau pour suspendre
[e programme et d6verroui[[er [e couverc[e.
REMARQUE : Si [a [aveuse tourne, [ecouverc[e peut mettre
que[ques minutes _ se d6verroui[[er. Appuyer pendant
3 secondes pour annu[er un programme.
TEMOINS LUMINEUX DES PROGRAMMES
sensing wash dnse spin de.e lid locked
Les te_moins lumineux indiquent la progression du
programme. ,_ chaque 6tape du processus, il est possible
que I'on remarque des pauses ou des sons diff6rents de
ceux des laveuses ordinaires.
SENSING (DI_TECTION)
sensing wash rinse spin done lid |ncked
Lorsqu'on appuie sur le bouton START/Pause/Unlock (mise
en marche/pause/ddwerrouillage), la laveuse effectue un test
automatique sur le m6canisme de verrouillage du couvercle.
On entend un d6clic, le panier effectue un I6ger tour, et le
couvercle se d6verrouille bri_vement avant de se verrouiller
nouveau.
Une fois que le couvercle a 6t6 verrouill6 une seconde fois,
la laveuse effectue des essorages courts _ basse vitesse pour
estimer la taille de la charge. Ces essorages de d6tection
peuvent prendre 2 _ 3 minutes avant que I'eau ne soit ajoute_e
la charge et il est possible que ces essorages 6mettent un
bruit de ronronnement. Si le t6moin de d6tection est allum6,
alors la laveuse fonctionne correctement. La laveuse d6place
ensuite bri6vement la charge, fair une pause pour permettre
I'eau de tremper la charge, et continue _ ajouter de I'eau.
Ce processus peut se r_p(_ter jusqu'_ ce que la quantit6 d'eau
correcte ait 6t6 ajout6e _ [a charge. I[ est aussi possible que
['on entende de ['eau cou[er dans [e distributeur, ajoutant [e
d6tergent _ [a charge.
REMARQUE : Eviter d'ouvrir [e couverc[e durant [a d6tection.
Le processus de d6tection recommencera une fois [a [aveuse
remise en marche. Le t6moin de d6tection s'a[[ume 6ga[ement
[ors des 6tapes de [avage du programme. Ceci est normal.
2O