MCA furniture Nakuru 40253 SX3 User manual

12
34
11
22
2
50KG
25mm/s
730-1230mm(with tabletop)
1200x600x16mm Particle Board
ET116G-2P4824
10%（Work continuously for 2 minutes, pause for 18 minutes）
0-40℃
21
5 6
11
78
4
910 1
11 12
1
x2
C
Ax4 Bx3x4
D
M6x12
x4
Ex8 Fx7 Gx12 H
C
B
x3
x1
Wooden
Dowel Pins
G
ST4.2x13
x4
C
5x5(with
cross head)
x1
E
M6x12
x4
A
Plug
x4
H
ST4.2x55
x12
Item No.
Column Stage
Max. Load Capacity
Max. Speed
Height Range
Tabletop Dimension
Frequency
Temperature
STEP1
STEP2
Attention: The drawings below are for guidance only and they may differ slightly from the product and fittings received. Please contact customer
service department if there are any missing tools or installation problems.
Plug
Wooden
Dowel Pins
4*4 Inner Hexagon Allen
Key/ 5*5 Allen Key
(with cross head) M6x12 M6x16 ST4.2x13 ST4.2x55
Component List Installation Diagram
No. Part Qty No. Part Qty
Front Tabletop Back Tabletop
Table Support Tube Column
Feet Beam Components
Baffle Power Plug
Cable Tie Switch Cord
Handset
Table Connect
Sheet Metal
2
5x5(with
cross head)
Assemble Tabletop 1. Set 3 Wooden Dowel Pins
Install Table Support Tube and
Beam Components 1. Tighten 4 screws(E)
2. Cover the plugs 4
screws on left and right
3. As shown in the figure, align the holes on the table
and tighten the 12 screws(H) with a cross allen key C.
Note: The motor faces the adapter side to prevent the
frame from being installed backwards and forwards
H
CC
E
A
6
3
3
1
2
3
12
4
5
10
8
9
11
7
6
B
2
1
12
G
controller
position
controller
position
Note: connect two tabletops closely.
2. Align the connecting sheet metal (12) of the two table plates with the holes as shown in the figure, press the
two table plates, and then use a 5x5 allen key (C) to tighten the screws (G).
Item No.: 40253 SX3 / 40253 WW3
Installation guide

C
4x4
x1
F
M6x16
x8
Cx1
G
ST4.2x13
x3
9
9
99
1
3 2
4
C
4x4
x1
D
M6x12
x4
●“▲”
●“▼”
STEP3
STEP4
STEP5
STEP6
Install Baffle and Handset
5x5(with
cross head)
Tighten the 2 screws with a 5x5 Phillips allen key.
The handset packing bag comes with screws.
Align the 3 holes on the table and tighten the screws (G).
Connect Wires and Fix Cables Connect the handset (11), adapter and motor as
shown in the figure
Use the cable tie (9) to sort out the cables in
a proper position and keeps the cable organized.
Tear off
Manage
Cables Fix
Install Column
As shown in the picture, insert the column
coupling into the gear box
Rotate the column (4) to the position
shown in the figure, and turn it
clockwise by 45 degrees after it is
fully inserted.
Rotate to the position shown in the
figure, use a 4x4 allen key (C) to screw
the screw D into the 1 and 2 positions,
and then tighten the screws in 3 and
4 positions.
Install Feet
As shown in the figure, install the table feet (5) on
the columns (4), and tighten 8 screws (F) with a
4x4 allen key.
How to use handset
Adjust the desk upwards
Adjust the desk downwards
50
1.Check if overloaded, max loading: 50kg;
2.Contact your supplier or dealer
1.Reset
2.Contact your supplier or dealer
Go down but not go up
Downward sliding
This marking indicates that this product should not
be disposed with other household wastes. To
prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the product
was purchased. They can take this product for
environmental safe recycling.
Operation
●
●
Button Lift Function
Reset Function
Press the“▲”or“▼" button to adjust the height of the desk.
(1) When at the lowest position, long press the "▼" button for more
than 5 seconds to enter the reset mode. The reset will be finished until
the lift system rebound and stop after reaching the bottom.
(2) When the lifting system fails, release the button, long press the
"▼" button, the reset will be finished until the lift system rebound and
stop after reaching the bottom.
12. If there appears damage of the power cord, please contact the manufacturer or a
professional for replacement.
18
18
4
D
C
9
C
F
54
7
G
11
CC
controller position
Note: install the handset
to where label is.
Das Symbol der durchgekreuzten Mülltonne
bedeutet, dass elektrische sowie elektronische
Teile nicht mit dem Hausmüll entsorgt werden
dürfen.Bitte den Gaming Desk beim
Recyclinghof getrennt entsorgen.
The crossed-out bin means that this product
includes electrical and electronic pieces that
must not be disposed of in the regular domestic
waste. Please dispose the Gaming desk
separately at the recycling centre.