Memorex MD6451BLK - Personal CD Player User manual

Before operating this product, please read these instructions completely.
Antes de operar este producto, sírvase leer este instructivo en su totalidad.
User’s Guide
Guía del Usuario
PERSONAL COMPACT DISC PLAYER WITH
60 SECONDS DIGITAL ANTI-SHOCK
PROTECTION AND REMOTE
REPRODUCTOR DE DISCO COMPACTO
PERSONAL CON PROTECCIÓN ANTI-SALTOS
DIGITAL DE 60 SEGUNDOS Y CONTROL REMOTO
MD6451R

1
SAFETY PRECAUTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This Caution Marking is located at the bottom enclosure of the unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION:
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
DANGER:
This product utilizes a Class 1 laser to read Compact Discs.
This laser Compact Disc Player is equipped with safety
switches to avoid exposure when the CD door is open and the
safety interlocks are defeated. Invisible and hazardous laser
radiation when open and interlock failed or defeated. Avoid
direct exposure to beam. Please do not attempt to defeat or
bypass the safety switches.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning and
power surges ARE NOT covered under warranty for this product.

2
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class
Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a res-
idential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Do not open the CD compartment while the CD is rotating.
• Always keep the CD compartment closed when not in use.
• Keep all foreign objects out of the CD compartment.
• Place the unit on a stable surface.
• Avoid installing the unit in locations described below:
• Places exposed to direct sunlight or close to heat radiating
appliances such as electric heaters.
• On top of other stereo equipment that radiates too much heat.
• Places lacking ventilation or dusty places.
• Places subject to constant vibration.
• Humid or moist places.
SAFETY PRECAUTIONS
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISES
ET POUSSER JUSQU’AU FOND.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.

3
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion and, most importantly, without affecting your sensitive
hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for your
protection.
Decibel
Level Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT
EXPOSURE:
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet engine
180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.
A
S
S
O
C
I
A
T
I
O
N
EST. 1924
E
L
E
C
T
R
O
N
I
C
I
N
D
U
S
T
R
I
E
S
EIA
We
LISTENING
For A Lifetime
Want You

4
LOCATION OF CONTROLS
1. LINE OUT Jack (Rear of Unit)
2. PHONES (Headphones) Jack
(Rear of Unit)
(HEADPHONES PART NO.
098B133BCRBKXX*)
3. VOLUME Control
(Rear of Unit)
4. DBBS (Bass Boost) Switch
(Rear of Unit)
5. CD Door OPEN Switch
6. ESP Button
7. MODE Button
8. PROG (Program) Button
9. Skip/Search oButton
10. Display
11. HOLD (ON/OFF) Switch
(Rear of Unit)
12. DC 4.5V Jack
z(Rear of Unit)
13. Battery Compartment
(Under CD Compartment)
(BATTERY COVER PART
NO. 037E6451BK080AA*)
14. CD Compartment
15. PLAY/PAUSE (®p)/POWER
ON Button
16. STOP (■)/POWER OFF
Button
17. Skip/Search nButton
*Consumer Replaceable Part
(See page 16 to order.)

5
LOCATION OF CONTROLS (CONTINUED)
1. PHONES (Headphones) Jack (Side of Remote)
(HEADPHONES PART NO. 098B133BCRBKXX*)
2. PLAY/PAUSE (®p)/POWER ON Button
3. Skip/Search oButton
4. VOLUME Control
5. STOP (■)/POWER OFF Button
6. Skip/Search nButton
REMOTE PART NO. RC-RCD1004*
*Consumer Replaceable Part (See page 16 to order.)
NOTES:
•To use the remote, plug it into the PHONES (Headphones) jack on the rear of the
main unit. Then plug your headphones into the PHONES (Headphones) jack on
the side of the remote.
•The controls on the remote work in the same way as the controls on the main unit.
• Adjust the Volume control on the main unit before controlling the volume on the
remote. Otherwise, the headphones will not have sound even if you adjust to the
highest volume on the remote.
• When the Hold switch on the main unit is in the hold (ON) position, the remote
can still control the main unit.
REMOTE

6
This CD player requires either two (2) “AA” cell batteries (not included) or
an AC adapter (not included).
BATTERY INSTALLATION
The battery indicator ( ) will appear in the CD display when the
batteries need replacing.
1. Open the CD compartment, then open the
battery compartment door by pressing in on
the tab and then lifting it. To prevent the
possibility of losing the cover, it cannot
be removed.
2. Insert two (2) “AA” cell batteries (not
included) according to the polarity diagram
inside the battery compartment. Alkaline
batteries are recommended for the longest
playing time.
AC OPERATION
To operate the unit using AC power, connect an AC adapter (not included) to
an AC outlet having 120V, 60Hz AC only. Plug the small end into the DC
4.5V jack on the unit and connect the other end into the AC outlet. The
batteries are automatically disconnected when the AC adapter is used.
CAUTION:When not using AC power, disconnect the AC adapter from
the wall outlet by pulling the plug (not the cord). Do not touch the AC
adapter with wet hands. Fully insert the plug without exposing any part of
the blade.
DC4.5V z
POWER SOURCES
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated inside the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Carbon-zinc or Rechargeable) or old
batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or
injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
–
+
–
+
–
+
–
+

7
OPERATION
To emphasize the bass, slide the
DBBS switch to the ON position. For
normal bass, slide the DBBS switch to
the OFF position.
1
To turn the unit on, press the PLAY/
PAUSE (®p)/POWER ON button ❶.
To turn the unit off, Press the STOP (■)
/POWER OFF button ❷while in the Stop
mode.
1
2
1
BASS BOOST TURNING POWER ON/OFF
AUTO POWER OFF
When the unit is stopped (Standby mode) for approximately 30 seconds, the
power will automatically turn off.
Radio Sound Through a Home Audio System
By using a home audio connection cable (not included), superb radio sound can
be heard through your home audio system. Before making any connections, turn
off the power to all equipment.
Plug a connection cable (not included) between the LINE OUT jack on the rear
of the CD player and the amplifier’s AUX or CD input jack. (Do not connect it to
the amplifier’s PHONO jack.)
NOTE: If the radio interferes with TV reception, move the unit away from the TV
or turn off the power to this unit.
Slide to the ON position to disable the buttons; “Hold” will appear in the display. Slide to the
OFF position to enable the buttons. For the HOLD function, only the buttons will be disabled,
not the other controls/switches (i.e., DBBS switch, VOLUME control, CD OPEN switch).
NOTE: When the Hold switch on the main unit is in the hold (ON) position, the remote can
still control the main unit.
1
HOLD SWITCH

8
CD OPERATION
Open the CD compartment lid by
sliding the CD OPEN switch to the
right. Gently press a disc, label side up,
onto the spindle until it locks in place.
Close the CD compartment lid. Insert
headphones into the PHONES jack.
1
Press the PLAY/PAUSE (®p)/POWER
ON button to turn the unit on; playback
will start automatically. To pause
PLAYBACK,press the PLAY/PAUSE
(®p)/POWER ON button, the elapsed
time will blink. Press once again to
resume playback.
2
TO PLAY A CD (Standard, CD-R and CD-RW)
Adjust the VOLUME control ❶and
DBBS switch ❷as desired. To skip
forward or backward through the tracks
on the disc, press the SKIP/SEARCH
o3or n 4 button.To search forward
or backward through the tracks on the
disc, press and hold the SKIP/SEARCH
o3or n4button.
2
1
34
3
When the disc is through playing, it will
stop. Press the STOP (■)/POWER OFF
button to stop the disc before it is
finished; the total number of tracks will
appear. Press the STOP (■)/POWER
OFF button again while in the Stop mode
to turn the unit off or wait approximately
30 seconds and the unit will automatically
turn off.
4
NOTES:
• This unit is capable of playing standard CDs or 3” singles; no adapter is required.
•If a disc is inserted incorrectly, dirty, damaged or not present at all, the display will
show “disc”.
•As each track is played, the track number and elapsed time are shown in the display.
• To remove the disc, open the CD compartment, hold the edge of the CD, gently
press the center pivot and lift the CD.
•The maximum play time for a CD in this unit is 74 minutes.
•“OPEN” will appear in the display when the CD door is open.

9
CD OPERATION (CONTINUED)
60 SECOND ELECTRONIC ANTI-SHOCK SYSTEM
This CD player has a built-in Anti-Shock System that cuts down on CD skipping,
which is useful when using the CD player in the car or while jogging/walking.
Follow the steps below to activate and understand the Anti-Shock System:
Open the CD compartment lid by
sliding the CD OPEN switch to the
right. Gently press a disc, label side
up, onto the spindle until it locks in
place. Close the CD compartment lid.
Insert headphones into the PHONES
jack.
1
With a CD inserted, press the
PLAY/PAUSE (®p)/POWER ON
button to turn the unit on and start
playback.
2
The Anti-Shock System will start
automatically, the sound will mute for a
moment and the display will blink
“ESP”.
Within a few seconds, “ESP” will light
solid to indicate music signals are
stored in memory.
3
CONTINUED ON THE NEXT PAGE
If the CD player is subject to vibration
during playback, “ESP” will blink
again. During the vibration, the music
should continue to play the signals
stored in the memory until the CD
player can read the music data
properly from the disc.
4

10
CD OPERATION (CONTINUED)
If no more vibration occurs, the
music signals are once again stored
into the memory and “ESP” will
again light solid. When the memory
is full, the disc rotation speed will
drop to save power consumption.
5
To turn the Anti-Shock System off,
press the ESP button.
To turn the Anti-Shock System on,
press the ESP button again.
6
NOTES:
• When the CD player is used in a stable location, turn the Anti-Shock System
off by pressing the ESP button. When the Anti-Shock System is off, battery
consumption is less.
• The Anti-Shock System provides for continuous sound output when the unit
is subject to vibration, but it will not correct errors, such as a defective or
dirty CD.

11
CD OPERATION (CONTINUED)
With a CD inserted, press the
PLAY/PAUSE (®p)/POWER ON
button ❶to turn the unit on, then select
atrack using the SKIP/SEARCH o2
or n3button. Press the MODE button
❹once; the Repeat 1 indicator 1
will appear in the display.
ALL
23
41
1
The unit will then play the same track
over and over until the STOP
(■)/POWER OFF button ❶is pressed.
Adjust the VOLUME control ❷and
DBBS switch ❸as desired.
3
2
1
2
TO REPEATEDLY PLAY BACK ONE TRACK
With a CD inserted, press the
PLAY/PAUSE (®p)/POWER ON
button ❶to turn the unit on. Press the
MODE button ❷twice; the Repeat All
indicator will appear in the
display.
ALL
21
1
The unit will then play all the tracks on
the CD over and over until the STOP
(■)/POWER OFF button ❶is pressed.
Adjust the VOLUME control ❷and
DBBS switch ❸as desired.
3
2
1
2
TO REPEATEDLY PLAY BACK ALL TRACKS
TO CANCEL REPEAT PLAYBACK,press the MODE button four times if in
Repeat 1 mode, or three times if in Repeat All mode. The unit will continue
normal playback.

12
CD OPERATION (CONTINUED)
With a CD inserted, press the
PLAY/PAUSE ( )/POWER ON
button ❶to turn the unit on and press
the STOP (■)/POWER OFF button ❷
to stop auto playback. Press the MODE
button ❸three times; the INTRO
indicator will appear in the display.
1
2
3
1
Press the PLAY/PAUSE ( )/POWER
ON button ❶to begin playback. The unit
will play the first 10 seconds of each
track. Adjust the VOLUME control ❷
and DBBS switch ❸as desired. Press
the STOP (■)/POWER OFF button ❹
to stop Intro playback.
3
2
1
4
2
INTRO PLAY
With a CD inserted, press the
PLAY/PAUSE ( )/POWER ON
button ❶to turn the unit on and press
the STOP (■)/POWER OFF button ❷
to stop auto playback. Press the
MODE button ❸four times; the RAND
indicator will appear in the display.
1
2
3
1
Press the PLAY/PAUSE ( )/POWER
ON button ❶to begin playback. The
unit will play all the tracks in random
order. Adjust the VOLUME control ❷
and DBBS switch ❸as desired. When
all the tracks have been played, the
unit will stop. Press the STOP
(■)/POWER OFF button ❹to stop
Random playback.
3
2
1
4
2
TO RANDOMLY PLAY BACK A CD
TO CANCEL Intro Play, press the Mode button twice.
TO CANCEL Random Play, press the MODE button once.

13
CD OPERATION (CONTINUED)
With a CD inserted, press the
PLAY/PAUSE (®p)/POWER ON button 1
to turn the unit on and press the STOP
(■)/POWER OFF button 2to stop auto
playback. Press the PROG button 3; the
Track “00” and PROG indicator will blink.
Also, the program “01” will appear in the
display.
1
2
3
1
Select the first track to be played back
using the SKIP/SEARCH o1or n❷
button, then press the PROG button ❸
again. Repeat this step to program
additional tracks up to a maximum of 20
tracks.
1
32
2
TO PROGRAM THE MEMORY (UP TO 20 TRACKS)
Press the PLAY/PAUSE (®p)
/POWER ON button ❶to begin
Programmed playback and adjust the
VOLUME control ❷and DBBS switch
❸as desired.
3
2
1
3
To skip forward or backward through
the programs, press the SKIP/
SEARCH o1or n❷button. When
the disc is through playing, it will stop.
12
4
NOTES:
• Press the STOP (■)/POWER OFF button to stop the disc before it is finished.
• Press the STOP (■)/POWER OFF button while in the Stop mode to turn the unit off and
clear the Program memory.
•As each program is played, the track number is shown in the display.
•Programming is the ability to preselect the order in which a series of tracks will be
played.
•Each track may be stored in the program memory as many times as desired (up to 20
tracks).
• To play the Program on Repeat, simply press the MODE button twice while playing the
Program.

14
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the compact disc carefully. Handle the
compact disc only by its edges. Never allow your
fingers to come in contact with the shiny,
unprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to
the compact disc label.
•Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to clean the compact disc. If necessary, use a
CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the disc, it is probably dirty
or damaged (scratched).
• When cleaning the compact disc, wipe in straight lines from the center of the
compact disc to the outer edge of the compact disc. Never wipe in circular
motions.
• This unit is designed to play only compact discs bearing the
identification logo as shown here. Other compact discs may not
conform to the CD standard and may not play properly.
• Compact discs should be stored in their cases after each use to avoid
damage.
•Do not expose compact discs to direct sunlight, high humidity, high
temperatures or dust, etc. Prolonged exposure or extreme temperatures can
warp the compact disc.
•Do not stick or write anything on either side of the compact disc. Sharp writing
instruments, or the ink, may damage the surface.
Cleaning the Unit
•To prevent fire or shock hazard, disconnect your unit from the AC power
source when cleaning.
•The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.

15
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before
calling for service.
SYMPTOM CAUSE SOLUTION
Unit will not Batteries inserted Insert batteries
turn on. incorrectly. correctly.
Weak or dead Replace batteries.
batteries.
AC adapter Check AC adapter
not connected. connection.
Disc will not play. CD compartment Close CD compartment.
not closed.
Disc inserted Reinsert disc correctly.
incorrectly.
Dirty or defective Try another disc.
disc.
Moisture Wipe disc with soft
condensation cloth.
on disc.
Erratic CD playback. Dirty or defective Clean or replace disc.
disc.
No sound from Headphone Reinsert headphone
headphones. plug not inserted plug correctly.
correctly.
VOLUME control Increase volume (main unit &
set to minimum. remote).
Weak batteries. Replace batteries.
Defective disc. Try another disc.
ESP not working. ESP is not activated. Press the ESP button.

16
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE
VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT [phone].
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90
DAYS IN CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR
PLACE OF PURCHASE OR MEMOREX.
FOR CONSUMER REPLACEABLE PART(S), SEE PART NUMBER(S) ON
PAGE 4 AND 5 AND THEN CONTACT FOX INTERNATIONAL
AT 1-800-321-6993.
Power requirements......................................2 x LR6 "AA" alkaline battery
DC In 4.5V adapter (center positive)
D/A conversion...................................1-bit DAC eight times oversampling
Frequency response ............................................20~20,000Hz (+1,-3 dB)
Anti-shock. .......................................................................60 second buffer
Output level...........................................Line output: 0.6 Vms (47K ohms)
Headphone: 16mW (32 ohms)
SPECIFICATIONS

1
MEDIDAS DE SEGURIDAD
ADVERTENCIA: Para reducir el riesgo de descargas eléctricas no saque la
cubierta o la tapa posterior. Allí no se encuentran partes que puedan ser
reparadas por el usuario. Lleve su unidad a un Centro de Servicio Autorizado.
Esta marca de alerta se encuentra en el fondo del gabinete de la unidad.
CUIDADO
RIESGO DE DESCARGA
ELÉCTRICA. NO ABRIR.
ADVERTENCIA: La figura de la flecha con forma de rayo dentro
de un triángulo está hecho para alertar al usuario de la
presencia de cables sin aislar de "voltaje peligroso" dentro del
gabinete, de tal magnitud que puede causar un riesgo de
descarga eléctrica a las personas.
ADVERTENCIA: El signo de exclamación dentro de un
triángulo está hecho para alertar al usuario de la existencia de
instrucciones importantes tanto de servicio como de
funcionamiento y mantenimiento que vienen con la unidad.
PELIGRO:
Este producto utiliza un láser de Clase 1 para leer los discos
compactos. Este reproductor de discos compactos con láser está
equipado con interruptores de seguridad para evitar el contacto
cuando la puerta del CD está abierta y el intercierre de seguridad
está vencido. Radiación láser invisible y riesgosa cuando está
abierto y el intercierre está averiado o vencido. Evite la
exposición directa al haz de luz. No intente vencer o circunvalar
los interruptores de seguridad.
AVISO DE LA FCC:
Este equipo genera o puede usar energía de frecuencia radial. Cualquier
cambio o modificación al equipo, puede causar interferencia nociva, a
menos que estas modificaciones esten expresamente indicadas en el man-
ual de instrucciones. El usuario puede perder el derecho de operar este
equipo si efectuara un cambio o modificación no autorizadas.
PROTECTORES DE PICOS:
Se recomienda utilizar un protector de picos para la conexión eléctrica. Los picos
del relámpago y de la energía no se cubren en la garantía de este producto.

2
AVISO DE LA FCC:
Este equipo genera o puede usar energía de frecuencia radial. Cualquier cam-
bio o modificación al equipo, puede causar interferencia nociva, a menos que
estas modificaciones esten expresamente indicadas en el manual de instruc-
ciones. El usuario puede perder el derecho de operar este equipo si efectuara
un cambio o modificación no autorizadas.
Este sistema está de acuerdo con los límites exigidos por la Clase B para dis-
positivos electrónicos tal como se especifican en la Parte 15 del Reglamento
FCC. Estos límites ofrecen una protección razonable contra la interferencia de
radio o televisión, aún cuando esté operando correctamente. Para eliminar
cualquier interferencia, usted puede intentar una o más de las siguientes medi-
das correctivas:
• Re-oriente o cambie de posición la antena receptora.
• Aumente la distancia existente entre el sistema y el radio o televisión.
• Use distintos toma-corrientes para el radio o la televisión.
• Si el problema subsiste, consulte a un técnico especializado en radio/tele-
visión.
• No abra el compartimiento del CD mientras el CD esté girando.
•Siempre mantenga el compartimiento del CD cerrado cuando no se esté usando.
• No meta objetos extraños en el compartimiento del CD.
•Coloque la unidad sobre una superficie estable.
• Evite instalar la unidad en los lugares descritos a continuación:
•Lugares expuestos a la luz directa del sol o cerca de aparatos que irradian calor
como calentadores eléctricos.
•Arriba de otros equipos estereofónicos que irradian demasia do calor.
• Lugares con poca ventilación o polvorientos.
• Lugares sujetos a una vibración constante.
• Lugares húmedos.
MEDIDAS DE SEGURIDAD
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISES
ET POUSSER JUSQU’AU FOND.
Este aparato digital de Clase B cumple con la norma ICES-003 de Canadá.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.

3
Estimado cliente:
El haber seleccionado un equipo de tan alta tecnología, como el que usted acaba de
comprar, es sólo el comienzo de su entretenimiento musical. Ahora es tiempo de tomar en
consideración como optimizar el entretenimiento que su equipo le ofrece. Este fabricante y
la Asociación de Industrias Electrónicas del Grupo de Consumidores Electrónicos desean
que usted obtenga el mejor resultado de su equipo usándolo en un nivel seguro, tal como el
escuchar el sonido claro y sonoro, sin distorsión - sobre todo sin que afecte su sentido
auditivo. El sonido es engañoso, ya que con el tiempo su nivel de audición puede
adaptarse solo a escuchar en volumen alto, resultando en un serio daño a su sentido
auditivo. Protéjase contra este daño innecesario ajustando el volumen de su equipo a un
nivel bajo antes de acostumbrarse a escuchar siempre la música a un volumen alto.
Para establecer un nivel auditivo seguro:
• Ponga el control de volumen en posición baja.
• Lentamente aumente el nivel hasta que usted pueda escuchar clara y
confortablemente sin distorsión.
Una vez que establece el nivel de audición confortable:
• Deje fijo el control de Volumen en dicho nivel.
Esto solo le tomará un minuto, y le ayudará a prevenir la pérdida del oído en el futuro.
Nosotros deseamos que usted pueda oir durante toda su vida
Si sabe usar su equipo, éste le proveerá mucho tiempo de satisfacción y entretenimiento.
Debido a que el daño causado al oido es imperceptible hasta que ya es muy tarde, este
fabricante y la Asociación de Industrias Electrónicas le recomiendan evitar la exposición
prolongada a ruidos excesivos. La lista que le damos a continuación le servirá de guía:
Nivel de
Decibeles Ejemplo
30 Una biblioteca, susurros.
40 Sala, refrigeradora, dormitorio lejos del tráfico.
50 Semáforo, conversación no rmal, oficina tranquila.
60 Aire acondicionado a 20 pies, máquina de coser
70 Aspiradora de polvo, secadora de pelo, restaurant bullicioso.
80 Tráfico de la calle, destructores de basura,alarma de reloj a dos pies.
LOS SIGUIENTES RUIDOS PUEDEN SER PELIGROSOS SI SE SOMETE A
ELLOS EN FORMA CONSTANTE
90 Subterráneo, motocicletas, tráfico de camiones, podadora de pasto.
100 Camión de basura, sierra eléctrica, perforadora neumática.
120 Concierto rock delante de los parlante, ruido de truenos.
140 Sonido de disparo, motor de jet.
180 Lanzamiento de una nave espacial.
Esta información ha sido proporcionada gratuitamente por la Fundación de
Investigación de la Sordera.
A
S
S
O
C
I
A
T
I
O
N
EST. 1924
E
L
E
C
T
R
O
N
I
C
I
N
D
U
S
T
R
I
E
S
EIA
We
LISTENING
For A Lifetime
Want You