Mendota AA-11-05391 User manual

85-03-01292-B FV33i FireIn
Installation and Operating Instructions
MODEL NO. AA-11-05391 FV33i FireIn FULLVIEW DIRECT VENT GAS FIREPLACE INSERT HEATER
WARNING: If the information in these instructions
is not followed exactly, a fire or explosion may
result causing property damage, personal injury, or
loss of life.
AVERTISSEMENT. Assurez-vous de bien suivre les
instructions données dans cette notice pour réduire au
minimum le risque d'incendie ou d'explosion ou pour
éviter tout dommage matériel, toute blessure ou la mort.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
•Do not try to light any appliance.
•Do not touch any electrical switch; do not
use any phone in your building.
•Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
•If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
Ne pas entreposer ni utiliser d'essence ni d'autres vapeurs
ou liquids inflammables dans le voisinage de cet appareil
ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous servir des
téléphones se trouvant dans le bâtiment où vous trouvez.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incendies.
- L'installation et l'entretien doivent être assurés par un
installateur ou un service d'entretien qualifié ou par le
fournisseur de gaz.
This appliance may be installed in an aftermarket,
permanently located, manufactured home (USA
only) or mobile home, where not prohibited by local
codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gasses unless a
certified kit is used.
Cet appareil peut être installé dans une maison
préfabriquée (É.-U. seulement) ou mobile déjà installée à
demeure si les règlements locaux le permettent.
Cet appareil doit être utilisé uniquement avec les types de
gaz indiqués sur la plaque signalétique. Une trousse de
conversion est fournie avec cet appareil.
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and must be installed.
Une barrière conçue pour réduire le risque de brûlures
du verre chaud est fournie avec cet appareil et doit être
installée.

85-03-01292 FV33i FireIn Page 2
READ ME FIRST
1.1 INITIAL FIRING AND CURING PROCEDURE
This product requires an initial heat curing cycle during which some materials used in the manufacturing process will burn
off and the powder paint goes through a hardening cycle. During the initial curing phase, some smoke and odor will be
emitted. This is normal.
The installer should perform these initial curing cycle procedures as the final step in the installation process before
finishing materials are installed around this fireplace. See chapter Mendota Fireplace Insert Curing Instructions. Read and
follow all instructions given in this Chapter and perform the 3-step curing cycle.
After the 3-step curing cycle has been completed, all smoking will have stopped. Some slight odors may remain. With
subsequent use of this Insert, odors will slowly dissipate and disappear.
ODOR RISKS
If the Woodburning fireplace firebox and chimney flue are not inspected and cleaned as required, the
heat from this Insert body and vent system may cause existing dirt, creosote, or mold to emit odor.
If this appliance is not operated for an extended period (three months or longer), when first fired
again, expect odors of burnt dust and lint; just like when turning on your home heating system for the
first time in the Fall.
1.2 HOT SURFACES ARE NORMAL
Mendota Inserts comply with ANSI Z21.88 Standards for maximum surface temperatures (ambient plus 117oF) on exposed
“combustible” surfaces adjacent to the Insert.
Be aware that the surface in front of, above and adjacent to this heater appliance can be too hot to touch. As long as all
required clearances to combustibles are met and the required finishing materials are used, this appliance will perform
safely. Note that the exposed surfaces immediately surrounding the Insert can have surface temperatures that are too hot
to touch. This level of surface temperature is considered normal and does not indicate any hazardous situation.
WARNING: The supplied barrier screen must be installed always when this fireplace is in operation.
Do not place any object directly in front (within 60”) or directly above (on the front edge of the
mantel). This is a heating appliance. Areas directly in front and above this appliance will be very hot
and can damage most household objects if placed too close. Keep Furniture pieces at least 60” away
in front of the barrier screen.
1.3 PERIODIC AND ANNUAL CLEANING ARE REQUIRED
See Required Periodic Inspections and Required Annual Maintenance.Periodic and Annual cleaning and general services
are required at least once a year in the Summer or early Fall. Changing remote control at least every 6 months is
required; or more frequently based upon usage frequency. Cleaning pilot flame sensor rod, sparker rod and pilot hood
body is required at least once per year. Cleaning of burner ports, gas orifice areas is required once a year due to insects’
nesting probability due to Mercaptan addition in Natural Gas (Mercaptan attracts insects).
1.4 KEEP THE FLUE WARM
It is required to activate the Continuous Pilot Mode (CPI) to leave the pilot light running during winter months when
outside daily high temperatures remain 50oF or lower. Doing so will eliminate heat loss from the home through the
fireplace Insert glass door and will increase flue draft during startups and will aid in eliminating system lock out.

Table of Contents
1.1 INITIAL FIRING AND CURING PROCEDURE ................................ 2
1.2 HOT SURFACES ARE NORMAL ............................................... 2
1.3 PERIODIC AND ANNUAL CLEANING ARE REQUIRED...................... 2
1.4 KEEP THE FLUE WARM ......................................................... 2
2.1 SAFETY AND WARNING INFORMATION......................... 5
2.2 SAFETY WARNINGS............................................................. 6
2.3 REQUIREMENTS FOR THE COMMONWEALTH OF MASS............... 9
3.1 GENERAL TECHNICAL REFERENCES ....................................... 10
3.2 MECHANICAL TECHNICAL REFERENCES.................................. 12
3.2.17.5.1 Paint Types Approved for Use ........................... 34
3.2.17.5.2 Sealants Type Approved for Use........................ 34
3.2.17.5.3 Wood Application Cautions ............................... 34
3.3 ELECTRICAL TECHNICAL REFERENCES .................................... 41
3.4 PLUMBING TECHNICAL REFERENCES ..................................... 45
4.1 INSTALLATION CHECKLIST ................................................... 49
4.2 UNPACKING THE INSERT..................................................... 50
4.3 CONTENTS OF THE MANUAL PACKET .................................... 51
4.4 WHAT IS NOT INCLUDED WITH THIS APPLIANCE?..................... 51
4.5 BENDING UP THE SHIPPING CLIPS ......................................... 52
4.6 LEVELING BOLTS............................................................... 53

4.7 GLASS DOOR REMOVAL AND REINSTALLATION ....................... 54
4.8 LIGHT BULB AND LIGHT LENS INSTALLATION .......................... 55
4.9 LIGHT BULB AND LIGHT LENS INSTALLATION .......................... 55
4.10 NATURAL GAS TO LPG CONVERSION.................................... 56
4.11 FIREPLACE CAVITY PREPARATION ......................................... 60
4.12 VENTING ........................................................................ 61
4.13 ATTACHING WARNING LABEL TO ZC WOODBURNING FIREPLACE
FLOOR....................................................................... 65
4.14 INSERT BODY INSTALLATION ............................................... 66
4.15 TUBE AIR SHUTTER CONTROL AND FLAME APPEARANCE........... 68
4.16 LIGHTING CHECKLIST ......................................................... 68
5.1 AESTHETIC CONSIDERATIONS .............................................. 69
5.2 HEATING PERFORMANCE ................................................... 69
5.3 IMPORTANT INFORMATION FOR HOMEOWNER ....................... 69
5.4 OPERATING INFORMATION......................................... 69
5.5 REMOTE CONTROL OPERATING INSTRUCTIONS....................... 72
5.6 IPI AND PILOT ON DEMAND MODES .................................... 74
5.7 FIRST TIME LIGHTING INSTRUCTIONS.......................... 75
5.8 OPERATING INSTRUCTIONS................................................. 75
5.9 TO TURN OFF GAS TO FIREPLACE ........................................ 75
5.10 FREQUENTLY ASKED QUESTIONS................................. 76
6.1 REQUIRED PERIODIC INSPECTIONS ....................................... 80
6.2 CLEANING VIEWING GLASS................................................. 80
6.3 REQUIRED ANNUAL MAINTENANCE...................................... 80
6.4 OVER FIRING OR UNDER FIRING OF BURNER .......................... 81
6.5 IGNITION SYSTEM LOCKOUT MODE AND RE-LIGHTING .............. 81
6.6 BURNER FLAME HEIGHTS REFERENCE DIAGRAM ..................... 81
6.7 REPLACEMENT PARTS INFORMATION ......................... 82
7.1 FINAL INSTALLATION AND HOMEOWNER CHECKLIST.. 87
7.2 WARRANTY POLICY STATEMENT .......................................... 88
7.3 CONDITIONS.................................................................... 89

85-03-01292 FV33i FireIn Page 5
GENERAL INFORMATION
2.1 SAFETY AND WARNING INFORMATION
2.1.1 Building Permit & Inspection Requirements
All installations of Mendota fireplaces and inserts must comply with all the requirements stated in this Installation and Operating
Manual. The dealer and/or installer must obtain all required building permits and inspection approvals from the local building
inspection department or the local jurisdiction. To validate warranty coverage, Mendota may require facsimile copies of the
building permit and inspection approval forms. Failure to provide adequate proof that the installation conforms to all local
requirements and the requirements stated in the Installation and User Manual will void all applicable warranties.
2.1.2 Other Cautions
This fireplace is not intended for outdoor installation. The fireplace must be installed where it is fully protected from all
precipitation, excessive moisture, and the ambient temperature remains between 32°F to 110°F. Failure to install the fireplace in
an area that meets these requirements will void all applicable warranties.
CAUTION: Each installation must conform to all local, state, and national codes. Refer to the national fuel
gas code and local zoning and code authorities for details on installation requirements. The Mendota
Fireplace must be vented to the outside in accordance with the latest edition of the National Fuel Gas Code.
In the absence of local codes, the installation must conform to the most current edition of the National Fuel
Gas Code ANSI Z223.1, also known as NFPA 54.
CAUTION: The Mendota Fireplace Insert may be installed in a manufactured (mobile) home after the first
sale of the home. Manufactured home (mobile home) installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable,
the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A, or CSA Z240.4-Gas Equipped
Mobile Housing. Consult your local building official. NOTE: For mobile home installations, unit must be
bolted to the Woodburning fireplace firebox floor and properly grounded.
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.
INSTALLATEUR : Laissez cette notice avec l’appareil. CONSOMMATEUR : Conservez cette notice pour
consultation ultérieure.