Merlin Myq 827au User manual

myQ®REMOTE LED LIGHT

Model 827AU

NOTE: The Remote Control supplied with your Remote LED Light is preprogrammed by the factory to the button shown in gure 1.

Installation

The myQ®Remote LED Light is designed to plug directly into a standard 240V outlet and not permanently wired. Consider installing close to an existing power

outlet. Nominal lumens is 1500, avoid directly looking at the lens when illuminated.

NOTE: If installing light on lasterboard and a ceiling joist cannot be located, use wall anchors provided. No pilot hole is required for wall anchors.

1. Drill pilot holes 6-1/8" (15.6 cm) apart if mounting to joist. OR Screw in wall anchors 6-1/8" (15.6 cm) apart if mounting to lasterboard.

2. Determine the length of power cord needed to reach the nearest 240V outlet. Wind any excess cord around cord retainer on the top side of the light base.

Route the cord through the channel so the light mounts ush.

3. Open the light lens.

4. Mount the light with the screws provided.

5. Close the light lens.

6. Plug in the light to the 240V outlet.

NOTE: The LED light is very bright and will blink while programming. DO NOT stare at the light while on a ladder.

To reduce the risk of SEVERE INJURY or DEATH:

• DO NOT alter the plug.

• Light is intended for indoor ceiling or wall mount applications ONLY.

Screws

Light Lens

Drywall

Anchors

6-1/8" (15.6 cm)

Cord Retainer

Channel

Wall Anchor (screw-in) (2) Screw # 6G x 25mm (2)

Pre-

programmed

Button

Hardware Provided

Installation Figure 1

Operation

Once the mains power is turned ON, the light can only be activated using Security+2.0 Remote Controls or the Merlin myQ®Internet app. A Security+ 2.0

Remote Control is supplied with this kit.

If paired with a myQ® garage door opener the myQ®Remote LED Light can also automatically turn ON or OFF in simultaneously with the garage door opener’s

internal light to boost the illumination of the garage.

NOTE: Wireless Wall Controls will not operate this device.

App Store is a service mark of Apple Inc. Google Play and the Google Play logo are require an additional accessory purchase or subscription fee.

Apple, the Apple logo, iPhone, and iPad are trademarks of Apple Inc.,

WARNING! This product contains a button/coin

cell battery.

•

The battery is hazardous.

•

Keep new and used batteries away from children.

•

Do not ingest battery. Chemical burn hazard.

•

If the coin cell battery is swallowed or placed

inside any part of the body, it can cause severe or

fatal injuries in 2 hours or less.

•

If the battery compartment does not close securely, stop using

the product and keep away from children.

•

If you think batteries might have been swallowed or placed

inside any part of the body, call the 24-hour Poisons Information

Centre on 13 11 26 in Australia, or the 24-hour National Poisons

Centre on 0800 764 766 in New Zealand, or seek immediate

medical attention.

•

Dispose of used coin/button cell batteries immediately and

safely. Flat batteries can still be dangerous.

Programming

PROGRAM AN ADDITIONAL SECURITY+ 2.0®REMOTE

CONTROL TO THE myQ® REMOTE LED LIGHT

1. Press the LEARN button on the Remote LED Light until the green LED

comes ON.

2. Press the button on the remote control (gure 2) that you wish to operate

the light.

3. The code has been programmed when the Remote LED Light blinks once.

LEARN Button LEARN Button 880LMW

Learn Button

LEARN Button LEARN Button 880LMW

LEARN Button

Chamberlain Australia Pty Ltd

PO Box 1446

Lane Cove NSW 1595

gomerlin.com.au

Ph: 1800 638 234

Chamberlain New Zealand Ltd

PO Box 100-221

AUCKLAND 0745

gomerlin.co.nz

Ph: 0800 653 667

114A5258B

Maintenance

• Unplug the light before cleaning.

• Use a lightly dampened cloth for cleaning.

• DO NOT use liquid cleaners on the light lens.

ADD THE myQ® REMOTE LED LIGHT TO myQ®ACCOUNT

Up to 16 myQ®devices can be paired to the myQ®Gateway. These devices include any combination of myQ®garage door openers and myQ®Remote LED

Lights.

NOTE: An active myQ® account with a connected myQ® Gateway is required for activating the myQ® feature. A myQ® Gateway is not provided with this unit.

1. Login to the myQ®app

2. Press the menu icon (top left corner).

3. Click on Device Management.

4. Under “HUBS”, click on the name of your Gateway.

5. Click “Add New”, select LED Remote Light and follow the steps.