Metal Fusion MR. OUTDOORS MOC3822 User manual

MODEL# MOC3822
THE INSTRUCTION MANUAL CONTAINS IMPORTANT INFORMATION NECESSARY FOR
THE PROPER ASSEMBLY AND SAFE USE OF THE MR. OUTDOORS
®
COOKOUT GRILL.
READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE ASSEMBLING AND
USING YOUR GRILL. FOLLOW ALL WARNINGS AND INSTRUCTIONS WHEN USING
THE PRODUCT. KEEP THIS MANUAL FOR FUTURE REFERENCE.
METAL FUSION, INC.
712 St. George Avenue.
Jefferson, LA 70121
If you have any problems or questions
Call Us Toll Free at
1-800-783-3885
7:30 A.M. to 3:30 P.M. CST • Monday through Friday
[phone]
WWW.MROUTDOORSCOOKOUT.COM
ASSEMBLY INSTRUCTIONS AND USE AND CARE MANUAL
MR. OUTDOORS
®
COOKOUT PORTABLE CHARCOAL GRILL
SERIAL # __________
FAILURE TO FOLLOW THESE INSTRUCTIONS
AND WARNINGS COULD RESULT IN FIRE, EXPLOSION, BURN HAZARD OR CARBON
MONOXIDE POISONING WHICH COULD CAUSE PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
English
V071522-E
DANGER -- CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no
odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a
camper, tent, car or home.
MONOXYDE DE CARBONE
Cette appareil peut produre du monoxyde de carbone,un gaz
inodore.
L’utilisation de cet appareil dans des espaces clos peut
entrainer la mort.
Ne jamais utiliser cet appareil dans un espace close comme unNe jamais utiliser cet appareil dans un espace close comme un
vehicule de camping, une tente, une automobile ou une maison.
PELIGRO--INTOXICACION POR
MONOXIDO DE CARBONO
Este artefacto puede producir monóxido de carbono, que es un gas
sin olor.
El uso de este artefacto en lugares cerrados podría provocar la
muerte.
No lo utilice nunca en espacios cerrados como casas rodantes,
No lo utilice nunca en espacios cerrados como casas rodantes,
carpa, automóvil u hogar.

FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS COULD RESULT IN
FIRE, EXPLOSION, BURN HAZARD OR CARBON MONOXIDE POISONING WHICH
COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
2
1) This is an ATTENDED product. Do NOT leave this product unattended while the product is in use. Monitor the
product when hot after use. Heated equipment can remain at high temperatures which can cause burns long after
operation. Use heat resistant gloves to handle hot tools.
2) This product is for OUTDOOR use only. Do NOT use in a building, garage, tent or any other enclosed area. Do NOT
use in or on a recreational vehicle or boat. NEVER use this product as a heater.
3) Do NOT locate this product under ANY overhead construction, overhanging trees and shrubs. Keep a minimum
clearance of 10 ft. (3.05m) from the sides, front and back of the product to ANY construction. Keep the area clear
of ANY combustible materials, gasoline and other flammable vapors and liquids. Do NOT use on or under ANY
apartment or condo balcony or deck. Never use in high winds.
4) Do NOT use under a canopy. Do NOT obstruct flow of combustion air and/or ventilation air for grill.
5) When in use the product must be on a level, stable, noncombustible surface such as brick, concrete, stone, or dirt.
Not suitable are surfaces such as wood, asphalt or plastic which may burn, blister or melt.
6) Children and pets should be kept away from the product and should be carefully supervised at all times. Children
and adults should be alerted to the hazards of high surface temperatures and flames and should stay away to
avoid burns or clothing ignition.
7) The use of alcohol, prescription or non-prescription drugs may impair your ability to properly assemble or safely
operate this product. Do NOT assemble or operate this product if using alcohol, prescription or non-prescription
drugs.
8) This product gets dangerously hot in use. Do NOT move the product when in use. Allow the product to cool completely
before moving or storing. Avoid bumping of or impact with the product. Prevent all contact with the hot product.
9) Do NOT use gas or kerosene to start the fire in your grill. Never add lighting fluid to hot or warm coals as a flash
back may occur causing serious injury or damage to property.
10) ALWAYS use long handled tools to safely handle food and wear oven mitts or gloves to protect your hands from
burns while handling. ALWAYS wear shoes while cooking. Keep hair and clothing from coming into contact with
the grill while in use or still hot. Ashes can remain warm for a long time after extinguishing.
11) Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this product. An
LP-cylinder shall not be stored near this product.
12) When operating, have a Type BC or ABC fire extinguisher readily available and adequate fire extinguishing material.
Do NOT use water to extinguish a grease fire. This can cause splatter which can result in serious burns or damage
to property.
13) This grill is not intended for commercial use. Use Mr. Outdoors® Cookout products in accordance with state and
local ordinances.
14) Read and follow all warnings on charcoal package. Dispose of coal ashes properly. Ashes can remain warm
for a long time after extinguishing. Do not remove ashes until they are fully extinguished and the grill is cool.
Never use the grill without ash tray installed and pushed completely into position.
15) Never put charcoal direcly on the bottom of the bowl. Always arrange charcoal on the charcoal grate.
16) Do not overload grill or warmer grill grate. Follow all directions in this manual for acceptable grill grate and
warming grate capacitites.
17) Screws can loosen during use. Check the grill’s stability prior to each use and tighten screws as needed.
18) Always check that all wing bolts are thoroughly tightened before each use.
19) Never use the grill grate handle on the smaller diamond shaped warmer grill to adjust the height. To adjust
the height always use the height adjustment arm on the warming grill grate rod to raise or lower the grill grate.
CALIFORNIA PROPOSITION 65 WARNING: Fuels used in wood or charcoal burning appliances, and the products of
combustion of such fuels, can expose you to chemicals including carbon black, which is known to the state of California to
cause cancer, and carbon monoxide, which is known to the state of California to cause birth defects or other reproductive
harm. For more information go to: www.P65Wanings.ca.gov
READ AND UNDERSTAND THIS MANUAL BEFORE USING THIS PRODUCT
FOR OUTDOOR USE ONLY

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING
YOUR MR. OUTDOORS®COOKOUT PRODUCT
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents ..................................................................................3
Warranty..........................................................................................3
Mr. Outdoors®Cookout Portable Charcoal Grill
Package Contents ....................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Parts List ..........................................................................................5
Assembly instructions..............................................................................6-8
Use and Care of Mr. Outdoors®Cookout Portable Charcoal Grill
Before Using Your Grill. ........................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Proper Placement for Use. ......................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Lighting and Operating Your Grill. . . . . . . . . . . . . . . . . . . . . . . . . . . . ......................................9-10
Maintenance & Storage ............................................ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Notes ............................................ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Owner’s Registration ............................................................................11-12
3
TABLE OF CONTENTS
WHAT THIS WARRANTY COVERS
This warranty covers all components of this product to be free from defects in materials and workmanship, with the
exceptions stated below.
HOW LONG COVERAGE LASTS
This warranty runs for one year from the date of purchase. Please keep your receipt with this manual for future reference.
WHAT IS NOT COVERED
This warranty does not cover the following:
Incidental and Consequential Damages. This warranty does not cover incidental and consequential damages
arising in any way out of the use of this grill. The liability of Metal Fusion, Inc. is, in any event, limited to the amount of
the original purchase price of this grill and remains in force only as long as the product remains in its original, as-built
configuration. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Neglectful Operation. This warranty does not cover any loss or damage arising in any way due to the negligent
operation of this outdoor grill.
Altered, Repaired or Misused Equipment. This warranty does not cover any loss or damage arising in any
way out of the use of this grill when it has been altered, repaired by persons other than Metal Fusion, Inc., or when it
has been abused or misused, or when it has been used other than in accordance with the manufacturer’s operating
instructions, including, without limitation, any damage to the consumer’s pots because they were placed on a lit grill
while the pot is empty.
Other Assumed Responsibilities. Unless otherwise provided by law, this warranty does not cover any
responsibility or liability arising in any way out of the use of this product where that responsibility or liability was
purportedly assumed by any other person or agent.
Paint, Discoloration, and Rust. This warranty does not cover the paint or finish on the grills, as in a normal use
of the outdoor grill, the paint may be burned off. Nor does this warranty cover discoloration or rust to the grill as these
occurrences are part of the grill’s normal wear and tear.
WHAT METAL FUSION, INC. WILL DO
Metal Fusion, Inc. will repair or replace any camp stove that proves to be defective in materials or workmanship. In the event
repair is not possible or economically feasible, Metal Fusion, Inc. will replace your grill with an identical or substantially
equivalent grill. Metal Fusion, Inc. will perform this service at no charge to you, except for the actual cost of shipping and
handling the outdoor grill or replacement parts.
HOW TO GET SERVICE
In the event you have a problem or malfunction with your grill, simply call Metal Fusion, Inc. at [phone].
HOW STATE LAW APPLIES
This warranty gives you specific rights, and you may have other rights which vary from state to state.
METAL FUSION, INC. - LIMITED ONE-YEAR WARRANTY

4
MR. OUTDOORS®COOKOUT PORTABLE CHARCOAL GRILL
PACKAGE CONTENTS
THE USE AND CARE MANUAL MUST BE READ AND UNDERSTOOD
BEFORE USING THE APPLIANCE
C
I
J
J
D
B
A
E
F
O
G
H
K
L
* Model May Vary From Picture
N
M
P
PACKAGE CONTENTS DIAGRAM

L - SMALLER DIAMOND SHAPED
WARMER GRILL GRATE (1)
PARTS LIST
A - CENTER SUPPORT
COLLAR WITH ASH
TRAY SLIDE RAILS (1)
B - LEG (3)
D - FIRE BOWL
HANDLE (2)
E - SMALL SILVER ASH
TRAY GUARD (1) F - LARGE BLACK CHARCOAL
GRATE (1)
G - ROTATIONAL
CRANK (1)
H - NOTCHED
ROTATIONAL
CRANK ROD
FOR LARGE
ROUND GRILL
GRATE (1)
I - STAINLESS STEEL
WARMING GRILL GRATE
ROD (1)
J - STAINLESS STEEL
GRILL GRATE
HANDLE (2)
K - LARGE ROUND
GRILL GRATE (1)
M - CUTTING BOARD (1)
FRONT VIEW W/LOGO
M - CUTTING BOARD (1)
BACK VIEW
W/SUPPORT ARMS
N - UTENSIL RACK (1) O - ASH TRAY (1)
A M6X18 17 X
PHILLIPS
HEAD BOLTS (17)
B M8 7 X
HEXAGON
HEAD NUTS (7)
WING BOLTS (3)
SHOULD BE PRE-INSTALLED
IN:
(1) FIRE BOWL
(1) LARGE ROUND GRILL GRATE
(1) SMALLER DIAMOND SHAPED
WARMER GRILL GRATE
C 17 X
FLAT WASHERS (17)
SQUARE HOLE
SLEEVE
FLAT RECTANGULAR SQUARE
PANEL
Placement
Sleeve
HEIGHT
ADJUSTMENT
DIMPLES
Placement
Sleeve
D 1 X
NON ADJUSTABLE
WRENCH (1)
HARDWARE PACKET CONTAINS BELOW QTYS:
HEIGHT
ADJUSTMENT
ARM
C - FIRE BOWL (1)
P- FOOT STAKES (3)
5

6
ASSEMBLY INSTRUCTIONS
Required Tools: (1) Phillips Screwdriver (not supplied)
(1) Non-Adjustable Wrench (supplied with hardware)
1. When assembling the grill make sure you have a at, even working space with ample room.
2. Pay attention to sharp edges of parts while you assemble the grill. It is advisable to wear protective work gloves during
the assembly.
3. Unpack the appliance and remove all the packaging as shown in Fig.1 below. Store the packaging out of reach of chil-
dren and after completing the assembly, please recycle the packaging following your local guidelines.
4. Turn the Center Support Collar with Ashtray Slide Rails (A) upside down as shown in Fig.2 below so that the bottom
of the ashtray slide rails are facing you and the tabs on the top of the support collar are at on the work surface. Assemble
Legs (B) by turning the legs upside down with the circular footpads located at the top. See Fig.2-4 below. Align the holes
in the leg end that is now at the bottom with the holes located in the support collar. The leg should be aligned on the out-
side of the support collar with the Mr. Outdoors® Cookout logo facing outwards. Place a at washer around each phillips
head bolt and then insert the phillips head bolt through the inside of either the top or bottom hole of the support collar and
into the pre-welded nut on the back of the leg that is aligned with the support collar hole. Repeat this step for the remaining
hole either above or below the one just assembled. Use a phillips head screwdriver to tighen bolts into the nuts which are
already welded on the backsides of the legs. Do not tighten completely, but rather tighten enough to hold in place. Repeat
this step for the remaining two legs. Once assembly is completed for all three legs, tighten all bolts completely.
5. Now turn the center support collar and leg assembly over so that it stands on the three legs with the round leg support
pads touching the ground. Pick up Fire Bowl (C) with the inside of the bowl facing upward and place it on top of the sup-
port collar. Align the holes in the bottom of the bowl with the holes located in the three at tabs on the top of the support
collar holes as shown in Fig.5. Put a at washer on a phillips head bolt and insert the bolt up through a tab on the center
support collar and into the re bowl. Screw a hexagonal nut around the end of the protruding bolt and tighten as shown in
Fig.6. Use a phillips screwdriver and the provided non-adjustable wrench to tighten. Do not overtighten to allow for all bolts
in the remainder of this step to be adjusted. Repeat this step for the two remaining bolt holes in the bottom of the bowl then
completely tighten all bolt assemblies.
Figure 1
Figure 2 Figure 3 Figure 4
Figure 5 Figure 6

6. Locate the two Fire Bowl Handles (D) and repeat the below steps for both handles. Align the holes on the handle with
the holes located on the outside rim of the re bowl. Put a at washer onto phillips head bolt and insert it through the hole
in the bowl handle and into the hole in the re bowl. Screw a hexagonal head nut onto the end of this bolt to connect the
handle to the re bowl. Use a phillips head screwdriver and use the provided non-adjustable wrench to tighten as shown in
Fig.7. Repeat this step for the remaining handle.
7. Insert the Small Silver Ash Tray Guard (E) into the large hole at the bottom of the re bowl. The lip around the ashtray
guard will hold it in place See Fig. 8. Next, place the Large Black Charcoal Grate(F) inside of the re bowl. The shape of
the bowl will hold this grate at the appopriate position as shown by Fig.9.
8. Align the four holes in the Rotational Crank (G) with the four holes on the at rectangular square panel located on the
side of the re bowl as shown by Fig.10. Place a at washer onto a phillips head bolt and screw the bolt into the hole on the
rotational crank. Do not securely tighten until all four bolts and at washers are in position. Repeat the above step for the ra-
maining three bolts and at washers. Once all four bolts and at washers have been installed, tighten securely with a phillips
head screwdriver as shown by Fig.11. See below Fig. 12 for completed Rotational Crank Installation.
9. Locate the Stainless Steel Warmer Grill Grate Rod (I) and insert this rod into the square hole sleeve opposite the
rotational crank along the re bowl rim shown in Fig.13. Insert the warmer grill grate rod into the square hole with the round
head on the rod pointing up as in Fig.14. Make sure the height adjustment dimples and adjustment arm are pointed to the
outside of the grill. A wing bolt must be tightened into the dimples on the outside of square hole sleeve and into one of the
height adjustment holes to secure the warmer grate rod in place.
7
Figure 7
Figure 8 Figure 9
Figure 10 Figure 11 Figure 12
Figure 13 Figure 14 Figure 15

8
10. Screw one of the Stainless Steel Grill Grate Handles (J) onto the threaded rod located above the placement sleeve
on the side of the Large Round Grill Grate (K) as shown in Fig.16. Then screw the remaining grill grate handle (J) onto the
Smaller Diamond Shaped Warmer Grill Grate (L). See Fig.17.
11. Position the placement sleeve located on the side of the large round grill grate over the round head of the rotational
crank as in Fig.18. The grill grate should be placed directly over the bowl. Now press rmly down to ensure that the grill
grate is pushed into the correct position on the rod. Once grate is on the rotational shaft securely, a wing bolt must be
screwed into the hole on the side of the placement sleeve. Make sure to screw this wing bolt in very tightly. It prevents the
grill grate from overextending to prevent the grill from becoming unbalanced during use. See Fig.19.
Repeat the above steps to secure the smaller diamond shaped warmer grill grate onto the stainless steel warmer grate sup-
port rod. All of the supplied wing bolts should now have been used. See Fig. 20&21.
12. Locate the Cutting Board (M). See Picture at Bottom of Page. The cutting board top should have the Mr. Outdoors®
Cookout logo engraved into the cutting area. Hang the cutting board onto the re bowl by placing the U-clips of the cutting
board support arms over the edge of the re bowl. The intended position for the cutting board is to the right of the rotational
crank, between the rotational crank and the re bowl handle. This should be on the side of the re bowl located over the
ash tray. The cutting board should sit ush with the top of the re bowl as shown in Fig.22 Below.
13. Locate the Utensil Rack (N) and hang this on the re bowl by hanging the notched sections on the utensil rack arms
over the edge of the re bowl. See Fig.23 at Bottom of Page. See Page 4 Package Contents Diagram for Further Refer-
ence.
14. Insert the Ash Tray (O) into the ash tray slot in the center support collar with ashtray side rails as shown in Fig. 24 at the
Bottom of th Page. Slide the ash tray on the slide rails. Ash tray will get extremely hot, do not attempt to dump ash tray dur-
ing use. Wait to handle ash tray until all ames have been extinguished and all ashes have cooled.
15. Go to the Use and Care section of this manual for further instructions.
Figure 16 Figure 17
Figure 18 Figure 19
Figure 20 Figure 21
Figure 22 Figure 23 Figure 24

USE & CARE
BEFORE USING YOUR GRILL
1. Read entire instruction manual before assembling your grill.
2. Wash the grill grates before first use with warm soapy water.
3. Test that both grill grates are properly installed above the fire bowl by rotating the grill grates out from left to right to ensure
that the stopping mechanism is engaged and that the grill grates do not rotate more than 45 degrees to the left of center and
45 degrees to the right of center.
If the stopping mechanisms do not engage the grill grates, make sure the grill grates are pushed down all the way on the ap-
propriate rods and re-tighten the wing bolts. Retest the grill grates to ensure that stopping mechanisms now engage the grill
grates and allow only the appropriate 45 degrees of rotation. If this problem can not be fixed by re-installing the grill grate(s)
and wing bolt(s) DO NOT USE THE GRILL. Please contact Metal Fusion, Inc. at 800-783-3885 M-F 7:30 - 3:00 CST.
WARMING GRATE AND GRILL GRATE CAPACITIES
Abide by the following maximum weight capacities: The below weight capacities are rated for the maximum weight that
the grill grates can withstand when rotated to the maximum rotational position allowed. When rotatating grill grates
the maximum rotational weight capacity ratings below must be followed for safe use.
- MOC3822 Grill - Warmer Grill Grate (Upper Diamond Grate) - 18 lbs. (8.16 kg)
- 22" (55.88 cm) Grill Grate (Lower Round Grate) - 18 lbs. (8.16 kg)
(3.05m)
CLEAR
OVERHEAD
GROUND LEVEL
10 FEET
to
NEAREST
COMBUSTIBLE
(All Directions)
Proper Placement
(3.05m)
10 FEET
to
NEAREST
COMBUSTIBLE
(All Directions)
GROUND LEVEL
NON-COMBUSTABLE SURFACE
9
LIGHTING AND OPERATING YOUR GRILL
REFER TO THE ASSEMBLY DIAGRAM ON PAGE 4 & PARTS LIST ON PAGE 5 TO REFERENCE THE PARTS LISTED
1. This is an ATTENDED appliance. Do NOT leave this grill unattended when hot or in use. Exercise the same care and caution
you would with an open fire. Never use in high winds. Completely extinguish fire before leaving the grill. Keep children and pets
away from the appliance at all times.
2. The ash tray (O) catches the ashes during grilling. Do not operate the grill without the built in ash tray. Caution! The ash
tray will be very hot. Do not remove the ash tray during use. It heats up and is very hot, and must be completely cooled
before being removed.
3.If using re starters, lay 2-3 re staters on top of charcoal grate (F) in the center of (C) re bowl. Follow all manufac-
turer's instructions supplied with the re starters. Add a maximum layer of 8 lb (3.63 kg) of charcoal to the center of the grill.
Light the re starters with a match or multipurpose lighter. Allow it to burn until the coals are half gray. With a long han-
dled, fire resistant tool, spread the coals evenly on the charcoal grate (F). If a warm and cool side is desired, push charcoal
to one side of the charcoal grate Never pour flammable liquids onto the lit charcoal.
If using a chimney starter, follow the manufacturer’s instructions on the starter and the charcoal. Set on top of char-
coal grate (F) in the center of (C) re bowl. Stuff the bottom of the chimney starter with paper or fire starter. Let burn until
flames come out of the top and the charcoal at the top is beginning to ash over. Dump on the center of charcoal grate (F).
Allow it to burn until the coals are half gray. With a long handled, fire resistant tool, spread the coals evenly on the char-
coal grate (F). If a warm and cool side is desired, push charcoal to one side of the charcoal grate. Never pour flammable
liquids onto the lit charcoal.
If using lighter fluid, stack a maximum layer of 6.6 lb (3 kg) of charcoal briquets on top of charcoal grate (F) in the center
of (C) re bowl. Saturate with lighter fluid according to the manufacturer's instructions. Never use gasoline or kerosene.
FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS COULD RESULT IN FIRE, EXPLOSION, BURN HAZARD OR
CARBON MONOXIDE POISONING WHICH COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
45°
GRAY AREA REPRESENTS THE APPROPRIATE ROTATIONAL
AREA OF THE GRILL GRATES
(45° TO THE LEFT AND RIGHT OF CENTER)
45°

IMPORTANT: When using liquid starters always check the ash tray before lighting. Fluid can collect in the ash tray and
could ignite, resulting in a fire below the bowl. Remove any starting fluid from the ash tray before lighting charcoal. Using a
match or multipurpose lighter, light the pyramid of coals in several places and allow it to burn until the coals are half gray.
With a long handled, fire resistant tool, spread the coals evenly on the charcoal grate (F). If a warm and cool side is desired,
push charcoal to one side of charcoal grate. Never pour flammable liquids onto the lit charcoal.
4. Once the flames have subsided, place the round grill grate (K) directly over the fire bowl (C) and carefully add food using
long handled, heat resistant tools. Do not swing the round grill grate (K) above the lit charcoal and add food until the flames
have disappeared. The grill, charcoal and cooked food will be very hot. Any contact with the grill can cause serious burns
during operation. Wear BBQ or kitchen gloves at all times. Only use long handled, heat resistant barbeque tools and uten-
sils. Do not wear clothes with loose sleeves. NEVER MOVE THE GRILL WHILE IT IS IN USE OR CONTAINS HOT ASHES.
5. Cutting board (M) can be used for convenience to place food on either during preparation for cooking or after cooking is
completed. Make sure not to allow cooked food to come in contact with raw food.
6. Place the cooked food on the smaller diamond shaped warmer grill grate (L) to keep it warm. The warming grill grate
can be adjusted in height. Remove food and pots from the diamond shaped warmer grill grate before adjusting the
height. Loosen the wing bolt to adjust the rod up or down to the desired adjustment hole setting. When adjusting height
always use the height adjustment arm of the stainless steel warmer grill grate rod (I). After setting the preferred
height, tighten the wing bolt securely to hold rod in place.
7. Use the utensil rack (N) to hang the long handled, heat resistant tools and utensils. The maximum loading of the utensil
bar must not exceed 2.2 lb (1 kg).
8.If using grill on a non combustible surface like shell, rock, or clay that will allow you to drive stakes through it, drive
Grill Stakes - (P), through holes on feet for added stability.
MAINTENANCE & STORAGE
FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS COULD RESULT IN FIRE, EXPLOSION, BURN HAZARD OR
CARBON MONOXIDE POISONING WHICH COULD CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
10
1. Make sure ashes have cooled before moving. Ashes should be placed in a non-combustible container after use. Clean
ashes out of grill after each use.
2. Wash the grill grate with mild soapy water. Do not use strong solvents or scouring pads as they can damage the surface
of your grill and leave abrasive marks.
3. Dry the product with a non-abrasive rag to make sure the product is free of moisture.
4. Cover all clean, dry grill components with a water resistent cover. Store in dry, cool area.
NOTES:

11
OWNER’S REGISTRATION
Dear Customer,
Thank you for purchasing a Mr. Outdoors® Cookout! Please take a moment
to fill out your registration form and return it to us. We are always happy to hear
suggestions and comments from our customers about our products. Completion
of this registration allows us to contact you if the need arises. Please keep your
receipt with your instruction manual. It will be necessary as a proof of purchase
for us to help you if there is a problem with your cooker.
Name:__________________________________________________________________
E-Mail: _________________________________________________________________
Address:________________________________________________________________
________________________________________________________________________
________________________________________________________________________
Telephone: _____________________________________________________________
Model# ________________________________________________________________
Date of Purchase ________________________________________________________
Place of Purchase _______________________________________________________
Price Paid ______________________________________________________________
Was this a gift _____ or did you _____ purchase it yourself?
________________________________________________________________________
________________________________________________________________________
Comments:
________________________________________________________________________
________________________________________________________________________
A SATISFIED CUSTOMER IS OUR MAIN GOAL. If you have any questions or
problems, please call us at 1-800-783-3885 before returning the product to the
point of purchase. Please have your receipt available when calling.
THANK YOU,
ENJOY YOUR COOKING EXPERIENCE.
CUT HERE

12
________________________
________________________
________________________
METAL FUSION, INC.
712 St. George Avenue
Jefferson, LA 70121
Place
Stamp
Here
FOLD
FOLD
TAPE HERE