Metalcraft 220-1-1 User manual

ECONOMIC MODEL
MODEL:3'X 5 'F T

1*24*1
3*16*17*19*2
10*112L*115*216*117*1
20U*1
20D*121R*121L*125L*1
25R*1
27*1
P1*1P1D*1P2*3P3*3P4B*1
P1A*1
P5*3P7*1D1*1
F1*142 F2*20 F3*4
S1*122 G2*2GB*1GC*4*14
Parts List
GD*2
75*6cm 150*13cm 150*6cm 77*3.5cm 147*3cm 72.5*2cm
147*2cm 152*12*4.7cm
87*2cm 162*2cm 162*2cm
3.2cm
62.5*2cm
165*37cm 165*37cm 165*28cm 165*38.5*7cm 165*46cm 165*26cm
87*46cm 87*37cm 164*64cm
77
.
5cm
12cm
4cm
77.5cm
12c m
4cm
165
cm
10cm
2.5cm
165 cm
10cm
2.5cm
59cm
2.7cm
3.2cm
59cm
2.7cm
4X10
M4X10 5X16
0.7X1CM 9X2CM
11.8X3.8cm 6X4.7cm
3.6X1.8cm
3X3cm

Assemble base bars from (1) to （4）with (F1) screws.
1

2Place the wall panel (P1)(P1D)(P2) on the base bar (1)(2)(3)(4)
side wall of the shed line up the holes with base bar,
s e c u r e w i t h ( F 1 ) , t h e w a l l p a n e l ( P 1 ) ( P 2 ) a s s e m b l y
together in mid of wall panel hole by (F2) screws

3Insert the 2 pieces of (G2) slider into the sliding channel (7),
screw (7) on (P1)(P1D) by (F1). Then screw (6) between front
wall panel and (7) by (F1).
Note: sliding channel (7) is not have holes, because it aluminum
material, very soft material, (F1) can easy screw.

4Place the top angel bars(9) (10) on the top of wall panel, line
up the holes with wall panels and fix with (F1) screws.
Then place the wall panel (P1A)(P3)(P4B) on the base bar
(1)(4), side wall of the shed line up the holes with base bar.
Secure with (F1),screws with washers from outside.

5Place the left door column (25L) on the top of base bar (3),
insert into the wall panel. Then secure the door column(25L)
with(F1) screws. Repeat the same for the right door column(25R).

6Place square panel (12L) and gable panel (21L)(21R) on the top of
slide channel(6) and side top bar(9) by the (F1) screws from inside.

7Place the roof panels (P5)(P7) on the top of wall panel and roof
supports, line up the boles and secure with (F1) and washers.
Note: all of (F1) screw inside need
assembly (S1), to prevent
scratches.

8Assemble the roof flashing (15)(16)(17) with roof panels. Secure with (F1)
screws with washers. Then place 4 piece of top corner(GC) on the
roof joints and secure with screws with washers.

9Assemble the door bar (20) to the door panel (D1)up by (F2) bolt and nut with
washer , assemble the door bar (20) to the bottom of door panel(D1)
by (F2) bolt and nut with washer. Assemble the door bar(27)
to the mid of door panel(D1) by (F2) bolt and nut with washer.
II
GD
20
20
GD

10 Fix 1 piece of the door handle (GB) with door panel (D1)
inside with (F2) bolt and nut.
Note: the door handle(GB) the third hole need fix with
door panel(D1) and door bar (27).

11 Slide the door panel(D1) assembly into the base bar (3),
then fix the panel top to the top slider (G2) with (F3) screws.
See figures below.