Micron M2T5055 User manual

www.microndisplaysolutions.com
Digital Menu Board
Wall Mount
Installation Instructions
M2T5055
M3T5055

Digital Menu Board 5055 Wall Mount Installation Manual Page 2
Rev. 09/18
Table of Contents
Important Safety Instructions............................................................................................................................. 3
Models and Specifications.................................................................................................................................. 4
Package Contents .............................................................................................................................................. 5
Step 1 –Using Two(2) Wide or Three (3) Wide Menu Board Mount Only......................................................... 6
Step 2 –Joining 2 Wide and 3 Wide Menu Board Mounts to make 4 Wide or great mount............................. 7
Step 3 –Fastening Temporary Wall Brackets to Wall ........................................................................................ 8
Step 4 –Mounting to Wall.................................................................................................................................. 9
Step 5 –Tilt Mechanism Adjustment .............................................................................................................. 10
Step 6 –Attaching End Caps............................................................................................................................. 10
Step 7 –Attaching VESA Panel Brackets & Mounting Panels........................................................................... 11
Step 8 –Installing Monitor Security Locks (Optional Item).............................................................................. 12
Step 9 –Installing Cable Tie Clamps (Optional Item) ....................................................................................... 12
Warranty........................................................................................................................................................... 13

Digital Menu Board 5055 Wall Mount Installation Manual Page 3
Rev. 09/18
Important Safety Instructions
Use the following safety guidelines to help protect you during the installation, especially with
installing the video panels to mount and when access to panels is required to ensure your own
personal safety.
Read all the installation instructions before installing the mounting solution.
Read and follow all important safety instructions.
Depending on size of video mount solutions, two (2) persons may be required for
installation.
Please ensure all safety precautions are followed when working with heights.
CAUTION: Before you begin any of the installation procedures read and follow the
warnings and important safety instructions within the manual.
WARNING!
FAILURE TO FOLLOW INSTRUCTIONS ON ACCESSING BEHIND PANELS AND
SERVICING PANELS MAY RESULT IN POSSIBLE PERSONAL INJURY AND
DAMAGE TO VIDEO PANELS DUE FROM FALLING!
BEFORE INSTALLING THE MOUNT, ENSURE THE WALL IS STRUCTUALLY
SOUND AND ABLE TO PROPERLY SUPPORT THE COMBINED WEIGHT OF
MOUNT AND VIDEO PANELS!
Cat No. M2T5055 and M3T5055
Tested and Evaluated to CSA Model Code SPE-1000, Clause 6.2.8.
Testé et évalué selon le code de modèle CSA SPE-1000, article 6.2.8
Warning: Maximum hanging load 100 Kg for M2T5055 and 120 Kg for M3T5055.
Attention: Charge maximale suspendue 100 Kg pour M2T4249 et 120 Kg pour
M3T4249.

Digital Menu Board 5055 Wall Mount Installation Manual Page 4
Rev. 09/18
Models and Specifications
Product
M2T5055
M3T5055
Type
2 Wide Tilt Menu Board
3 Wide Tilt Menu Board
Screen Sizes
50” to 55”
Tilt
0 to 15 Degrees
Vesa
200 to 400
Security Locks
Included
Weight Load
120 kg
140 kg
Dimensions (WxHxD)
With 00Tilt
2100 x 240 x 75mm
3200 x 240 x 75
Dimensions (WxHxD)
With 150Tilt
2100 x 240 x 120mm
3200 x 240 x 120mm
Note:
When joining Digital Menu Board mounts together to make overall 4 wide
or larger mount please add 400mm at each joining point to arrive at
overall length.

Digital Menu Board 5055 Wall Mount Installation Manual Page 5
Rev. 09/18
Package Contents
Description
Model
Qty
Picture
Preassembled Mount
2T5055
1
Part A
3T5055
2
Joiner Rail Assembly
2T5055
4
Part JR
3T5055
Panel VESA Bracket
2T5055
4
Part B
3T5055
6
End Cap
2T5055
8
Part EC
3T5055
Hardware
2T5055
2
Part H
3T5055
3
Cable Tie Clamp
2T5055
3
Part CC
3T5055
4
Monitor Security Lock
2T5055
2
Part SL
3T5055
3
Wall Bracket with
hardware
(Temporary)
2T5055
3
Part WB
3T5055
4
N/R = Not Required

Digital Menu Board 5055 Wall Mount Installation Manual Page 6
Rev. 09/18
Step 1 –Using 2 Wide or 3 Wide Menu Board Mount Only
Instructions
Diagrams
Do Not Remove Zip Ties
Holding Mount Yet!.
For a two (2) wide
mount proceed to Step
3.
Fig. 1A
Do Not Remove Zip Ties
Holding Mount Yet!.
For a three (3) wide
mount the left and right
sections need to be
joined together using
four (4) joiner bars
supplied. See figure 1B.
Once they are joined
together, tighten using
4mm Allen wrench. See
figure 1C, and 1D.
Fig. 1B
Fig. 1C Fig. 1D

Digital Menu Board 5055 Wall Mount Installation Manual Page 7
Rev. 09/18
Step 2 –Joining 2W & 3W Mounts to make a 4W or greater
Mount Type
Instructions Diagrams
For configurations
requiring 4 wide or 6
wide menu boards.
a) Join a 2W+2W menu
board mount using the
four (4) Joiner Rail
Assemblies provided
(Part JRS). See fig.2A,
and 2B.
b) Tighten screws using
4mm hex wrench once
they are in place. See
fig. 2C and 2D.
Fig. 2A
Fig. 2B
Fig. 2C Fig. 2D
For configurations
requiring 5 wide menu
boards.
c) Join a 2W+3W menu
board mount using the
four (4) Joiner Rail
Assemblies provided
(Part JRS). See fig.2A,
2E.
d) Tighten screws using
4mm hex wrench once
they are in place. See
fig. 2C, and 2D.
Fig. 2E
For configurations
requiring 6 wide menu
boards.
e) Join a 3W+3W menu
board mount using the
four (4) Joiner Rail
Assemblies provided
(Part JRS). See fig.2A,
and 2F.
f) Tighten screws using
4mm hex wrench once
they are in place. See
fig. 2C, and 2D.
Fig. 2F

Digital Menu Board 5055 Wall Mount Installation Manual Page 8
Rev. 09/18
Step 3 –Fastening Temporary Wall Brackets to Wall
Instructions
Diagrams
a) Determine center point for menu board
on wall. See figure 3A.
1. Mark wall with centre point
2. Mark wall with outside
measurements for menu board.
3. Determine location of wall studs.
Note: Minimum of three (3) studs must
be used to fasten mount to safely
support weight of mount and screens
for wood or steel studded walls.
Fig 3A
a) At either end of the mount placement
mark the outer most studs with the
desired reference height for mount.
b) Using a laser level or other level mark
the desired height on each stud behind.
See figure 3C and 3D.
c) These marks at each stud location will
be used to drill holes for mounting the
Wall Brackets (Part WB).
d) Screws for woods studs included, for
other types of studs appropriate
fasteners required (not included)
Fig. 3C
Fig. 3D
IMPORTANT
All of these Wall Brackets MUST be exactly
at the same height!
e) Attach Wall Brackets to at least 3 studs
for each 2 Wide mount and at least 4
studs for 3 Wide mount. See figure 3E.
f) Hardware for mounting to wood
supplied.
Fig. 3E

Digital Menu Board 5055 Wall Mount Installation Manual Page 9
Rev. 09/18
Step 4 –Mounting to Wall
Instructions
Diagrams
e) Lift mount and place so top wall rails
are seated as shown in figure 4A.
f) This will allow mount to stay on wall
temporarily to allow for easy marking
and pre drilling into wall for fastening
screws.
g) Using a level adjust wall brackets as
necessary to level mount.
h) There are predrilled holes in the top
and bottom wall rails (fig. 4B) every
eight (8) inches to position at stud
locations. Fastening hardware for wood
studs only included. See figure 4B and
4C.
Important:
Ensure the proper type of fastening
hardware is used to ensure maximum
handling load can be supported.
Fig. 4A
Fig. 4B
Fig. 4C
Fig. 4D
i) Remove cable ties once mount is
properly fastened to wall structure.

Digital Menu Board 5055 Wall Mount Installation Manual Page 10
Rev. 09/18
Step 5 –Tilt Mechanism Adjustment
Instructions
Diagrams
For a 2 wide mount there is a tilt
adjustment mechanism at each end.
For a 3 wide mount there are four (4) tilt
adjustment mechanisms.
The maximum tilt angle is 15 Degrees.
a) To set desired tilt angle, loosen the tilt
adjustment screws using a 4mm Allen
wrench.
b) Once you have the desired tilt angle
tighten the tilt adjustment screws.
Fig. 5A
Step 6 –Attaching End Caps
Instructions
Diagrams
a) Install the Black End Caps on both ends
of mount if not already installed. See
figure 6A and 6B.
b) Use clear silicone (optional) to affix End
Caps.
Fig. 6A Fig. 6B
Tilt adjustment screw
Tilt safety screw.
DO NOT ADJUST