midiplus X III Series User manual

SERIES
USERMANUAL
MIDIPLUS

1
X III Series User Manual
Contents
Introduction ............................................................................................................................................................................. 2
Important Notes:.................................................................................................................................................................... 2
1. Overview .............................................................................................................................................................................. 3
1.1 The Top Panel................................................................................................................................................................................... 3
1.2 The Rear Panel ................................................................................................................................................................................3
2. Guide .................................................................................................................................................................................... 4
2.1 Ready to use.................................................................................................................................................................................... 4
2.2 X Knob ................................................................................................................................................................................................5
2.3 Transpose and Octave ................................................................................................................................................................ 5
2.4 Pitch and Modulation ................................................................................................................................................................... 5
2.5 Knobs .................................................................................................................................................................................................. 6
2.6 Transport Buttons.............................................................................................................................................................................6
2.7 Keyboard........................................................................................................................................................................................... 7
3. Setting Mode ...................................................................................................................................................................... 7
3.1 Changing The X Knob Mode ....................................................................................................................................................7
3.2 Changing The Transport Buttons Mode................................................................................................................................. 8
3.3 Changing The Keyboard Velocity Curve.............................................................................................................................. 8
3.4 Changing The Bank MSB.............................................................................................................................................................8
3.5 Changing The Bank LSB............................................................................................................................................................... 8
3.6 Selecting a Smart Scale.............................................................................................................................................................. 9
3.7 Changing The CC Number ....................................................................................................................................................... 9
3.7.1 Changing The Knobs’CC Number................................................................................................................................. 9
3.7.2 Changing The Buttons’CC Number............................................................................................................................... 9
3.7.3 Changing The Mod Touch Strip’s CC Number .......................................................................................................10
3.8 Changing The Controller Channel .......................................................................................................................................10
3.9 Changing The MIDI Channel ..................................................................................................................................................10
4. Factory Reset .................................................................................................................................................................... 10
5. DAW Settings ..................................................................................................................................................................... 11
5.1 Steinberg Cubase/Nuendo (Mackie Control) ..................................................................................................................11
5.2 FL Studio (Mackie Control)........................................................................................................................................................13
5.3 Studio One (Mackie Control)...................................................................................................................................................14
5.4 Pro Tools (HUI) .................................................................................................................................................................................16
5.5 Logic Pro X (Mackie Control) ...................................................................................................................................................17
5.6 Reaper (Mackie Control)...........................................................................................................................................................18
5.7 CakeWalk Sonar (Mackie Control) ........................................................................................................................................20
5.8 Bitwig (Mackie Control) ..............................................................................................................................................................22
6. Appendix............................................................................................................................................................................ 24
6.1 Specifications ................................................................................................................................................................................24
6.2 Screen display and functional interpretation...................................................................................................................24
6.3 Scales................................................................................................................................................................................................25
6.4 MIDI CC List.....................................................................................................................................................................................26

2
X III Series User Manual
Introduction
Thank you for purchsing the 3rd generation X series MIDI keyboard. They are available in three models:
X4 III, X6 III, and X8 III. They all features full size keyboard with velocity sensitive, 4 knobs, 6 buttons, Pitch
and Modulation touch strips. Build in 16 Smart scales included Chinese pentatonic, Jananese scale,
Blues scale etc.. Also supports Mackie Control and HUI protocols, provides you with a better use
experience.
Important Notes:
Please read the following precautions carefully before use to avoid damaging the
equipment or causing personal injury. Precautions include but are not limited to the
following:
1. Read and understand all the illustrations.
2. Always follow the instructions on the device.
3. Before cleaning the device, always remove the batteries and the USB cable. When cleaning, use a
soft and dry cloth. Do not use gasoline, alcohol, acetone, turpentine or any other organic solutions;
do not use a liquid cleaner, spray or cloth that's too wet.
4. Disconnect the USB cable and remove the batteries if not used for extended periods.
5. Do not use the device near water or moisture, such as a bathtub, sink, swimming pool or similar
place.
6. Do not place the device in an unstable position where it might accidentally fall over.
7. Do not place heavy objects on the device.
8. Do not place the device near a heat vent at any location with poor air circulation.
9. Do not open or insert anything into the device that may cause a fire or electrical shock.
10. Do not spill any kind of liquid onto the device.
11. Do not expose the device to hot sunlight.
12. Do not use the device when there is a gas leak nearby.

3
X III Series User Manual
1. Overview
1.1 The Top Panel
1.2 The Rear Panel
12
5
6
7
34
8
1
234
①X knob: Control DAW and software instrument parameters or setting the keyboard parameters.
②Display: Provides real time feedback of control information.
③Knobs: Control DAW or software instrument parameters.
④Transport buttons: Control the transport of DAW.
⑤Transpose button: Activate keyboard’s semitone control
⑥Octave buttons: Activate keyboard’s octave control.
⑦Pitch & Modulation touch strips: Control the pitch bend and modulation parameters of your sound.
⑧Keyboard: Trigger notes on/off, also can be used as shortcuts to access edit more parameters.
①MIDI OUT: Connect to MIDI device or modular
②USB: Connect to your computer, this port provides both power and MIDI data
③SUS: Connect to a sustain pedal
④EXP: Connect to a expression pedal

4
X III Series User Manual
2. Guide
2.1 Ready to use
Use with computer: Connect X III to your PC or Mac using the included USB cable. Power is also supplied
through this connection. X III is a class-compliant USB device, so its drivers are automatically installed
when connecting to a computer.
Use with MIDIPLUS miniEngine series sound engine: Connect X III to the USB Host of miniEngine using the
included USB cable, connect your speaker or headphone to miniEngine and turn on the miniEngine.
Use with external MIDI device: Connect to a USB 5V power adapter using the included USB cable,
connect the MIDI OUT of X III to MIDI IN of external MIDI device with a 5 pin MIDI cable.
DC 5 V

5
X III Series User Manual
2.2 X Knob
The X knob has two working mode, power on defaults to normal mode, press it about 0.5 seconds to
switch to setting mode, the relevant parameter options of the keyboard can be set in this mode, for
more detailes, please refer to 3. Setting Mode.
Normal Mode: Turn the X knob to send Program Change(default) or CC7 message, this option can be
changed by Setting Mode.
Setting Mode: Turn the X knob to select options, press to confirm, press about 0.5 seconds to exit the
setting mode.
2.3 Transpose and Octave
Pressing the ◀ or ▶ button to shift the octave range of keyboard, when activated, the selected octave
button will light up, pressing the ◀ and ▶ buttons simultaneously will quickly reset the octave shift.
Press and hold the TRANS button, then pressing the ◀ or ▶ button to transpose, when activated, the
TRANS button will light up, and this can be toggled on and off by pressing the TRANS button, when off,
the TRANS button backlit will dimmer, the previously used transpose setting will be stored while the unit
remains powered.
2.4 Pitch and Modulation
Two capacitive touch strips allow for real-time pitch bend and modulation control. The LED light strips will
reflect the current status of each controller.
Sliding up or down on the Pitch touch strip will raise or lower the pitch of the selected tone. The range of
this effect is set within the hardware or software instrument being controlled.

6
X III Series User Manual
Sliding up on the Modulation touch strip increases the amount of modulation on the selected tone. The
response depends on the settings of the instrument being controlled. Certain instruments or presets will
not use the modulation parameter.
2.5 Knobs
X III has 4 assignable knobs with backlit, the default control functions of each knob are as follows:
Knob Purpose MIDI CC Number
K1 Chorus Send Level CC93
K2 Reverb Send Level CC91
K3 Timbre/Harmonic CC71
K4 Brightness CC74
You can assign any MIDI CC (continuous controller) number to each knob in Setting Mode. Please refer
to 3.7.1 Changing The Knobs CC Number for detailed operation steps.
2.6 Transport Buttons
X III has 6 buttons with three mode: MCU(default), HUI and CC mode, you can change this in Setting
Mode. Please refer to 3.2 Changing The Transport Buttons Mode for detailed operation steps.
In MCU and HUI mode, these buttons controls the transport of DAWs, and control the in CC modeplease
refer to 5. DAW Settings for detailed operation steps:
Button Purpose MIDI CC Number
B1 Undefined CC25
B2 Undefined CC26
B3 Undefined CC27
B4 Undefined CC28
B5 Undefined CC29
B6 Undefined CC30
Any MIDI CC number can be assigned to each button in Setting Mode, please refer to 3.7.2
Changing The Buttons’CC Number for detailed operation steps.
• ► ■
B1 B2 B3 B4 BS B6

7
X III Series User Manual
2.7 Keyboard
X III features 49, 61 or 88 velocity sensitive keys for playing and sending note on/off messages. These
keys also can be used as shortcuts to set controllers, MIDI channel in Setting Mode, for details, please
refer to 3. Setting Mode.
When in Setting Mode, the keys with labeled functions will be used as shortcuts to access the
parameters, the labeled keys as follow:
X MODE: Changing the X knob mode, select between Program Change (default) or CC mode.
BTN MODE: Changing the Transport button mode, select between Mackie Control (default), HUI and
CC mode.
VEL.: Setting the keyboard velocity sensitive curve, select between Normal (default), Fixed, Light and
Hard.
MSB: Setting the controller number for "Most Significant Byte" (ie, MSB) of Bank Select. This message has
a range between 0 and 127. The default is 0.
LSB: Setting the controller number for "Least Significant Byte" (ie, LSB) of Bank Select. This message has a
range between 0 and 127. The default is 0.
SCALE: Selecting the build in Smart Scale, when a scale is selected, the scale notes will be mapped on
the white keys, for details, please refer to 6.3 Scales, the default is Off.
ASSIGN CC: Setting the CC Number of each controller, including Mod touch strip, 4 knobs and 6
buttons, the range between 0 and 127.
ASSIGN CH: Setting the MIDI Channel of each controller, including Mod touch strip, 4 knobs and 6
buttons, the range between 0 and 16, the default is 0.
MIDI CHANNELS: Setting the MIDI Channel of keyboard, the range between 1 and 16, the default is 1.
3. Setting Mode
In the Setting Mode, you can set your keyboard easily. Long press the X knob about 0.5 second, the
screen will display "SEL" when enter the Setting Mode.
3.1 Changing The X Knob Mode
Long press the X knob about 0.5 second, when the screen display "SEL", then follow these steps:
1. Press the key labeled "X MODE", the screen will display the currently selected mode,
2. Turn the X knob to select Program Change or CC mode (the screen will display "PC" or "cC"),
3. Press the X knob to confirm, the screen will display you just selected mode,
Now you can press the other keys labeled functions to set other parameters, or long press the X knob to
exit the Setting Mode.

8
X III Series User Manual
3.2 Changing The Transport Buttons Mode
When the screen display "SEL", follow these steps:
1. Press the key labeled "BTN MODE", the screen will display the currently selected mode,
2. Turn the X knob to select Mackie Control, HUI or CC mode (the screen will display "MCU", "hui" or "cC"),
3. Press the X knob to confirm, the screen will display you just selected mode,
Now you can press the other keys labeled functions to set other parameters, or long press the X knob to
exit the Setting Mode.
3.3 Changing The Keyboard Velocity Curve
When the screen display "SEL", follow these steps:
1. Press the key labeled "VEL.", the screen will display the currently selected velocity curve,
2. Turn the X knob to select Normal, Fixed, Light or Hard (the screen will display "nor", "fix", "lig" or
"har"),
3. Press the X knob to confirm, the screen will display you just selected velocity curve,
Now you can press the other keys labeled functions to set other parameters, or long press the X knob to
exit the Setting Mode.
3.4 Changing The Bank MSB
When the screen display "SEL", follow these steps:
1. Press the key labeled "MSB", the screen will display the currently value,
2. Turn the X knob to set the controller number between 0 and 127,
3. Press the X knob to confirm, the screen will display you just selected controller number,
Now you can press the other keys labeled functions to set other parameters, or long press the X knob to
exit the Setting Mode.
3.5 Changing The Bank LSB
When the screen display "SEL", follow these steps:
• ► ■
B1 B2 B3 B4 BS B6

9
X III Series User Manual
1. Press the key labeled "LSB", the screen will display the currently value,
2. Turn the X knob to set the controller number between 0 and 127,
3. Press the X knob to confirm, the screen will display you just selected controller number,
Now you can press the other keys labeled functions to set other parameters, or long press the X knob to
exit the Setting Mode.
3.6 Selecting a Smart Scale
When the screen display "SEL", follow these steps:
1. Press the key labeled "SCALE", the screen will display the currently scale,
2. Turn the X knob to select a scale,
3. Press the X knob to confirm, the screen will display you just selected scale name.
3.7 Changing The CC Number
The controllers of X III can be assigned to any CC Number as you like, please refer to 6.4 MIDI CC List
for details. These controllers included: Mod touch strip, 4 knobs and 6 buttons, the range between
0 and 127.
3.7.1 Changing The Knobs’CC Number
When the screen display "SEL", follow these steps:
1. Press the key labeled "ASSIGN CC", the screen will display the CC number of the last use controller,
2. Turn the knob you want to assign, K1 for instance, the screen displays "93",
3. Turn the X knob to select a CC number, select "52" for instance,
4. Press the X knob to confirm, the screen displays "93",
5. Long press the X knob to exit the Setting Mode.
Now the CC number of K1 knob is assigned to CC52 successfully.
3.7.2 Changing The Buttons’CC Number
When the screen display "SEL", follow these steps:
1. Press the key labeled "ASSIGN CC", the screen will display the CC number of the last use controller,
2. Press the button you want to assign, B2 for instance, the screen displays "26",
3. Turn the X knob to select a CC number, select "53" for instance,
4. Press the X knob to confirm, the screen displays "53" you just selected number.
5. Long press the X knob to exit the Setting Mode.
Now the CC number of B2 button is assigned to CC53 successfully. Then you should change the button