Milennia MIL-AMP200BT User manual

MIL-AMP200BT
4 Channel Amplifier With Bluetooth Function

CONNECTING THE POWER
RCA INPUT AND HIGH INPUT INPUT
SENSITIVITY: 250mV-6V
LPF/FULL/HPF SELECTION SWITCH
CAUTION
A S A P R E C A U TI O N , IT I S AD V I S A BL E T O D I S C O NNE C T T H E V E H I C L E ＇ S B A TT E R Y B EF O R E M A K I N G C O NNE C TI O N T O THE
+ 12 VOLT SUPPLY WIRNG(Fig .1)
10 GAUGE (or a large guage of wire if planning for additional Amplifiers )wire is
recommended for the power and ground wires. 20 Gauge, for the remote
turn-onwire.BothtypesareavailableatmostMobileAudioDealers orInstallation
Shops.
GROUND: To Vehicle Chassis
Toavoidunwanted ignitionnoisecausedby groundloops,itisessential that the
Amplifier be grounded to a clean, bare,metal surface of the vehicle ＇ s chassis.
NOTE
GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT. ( 1 METER).
USING THIS METHOD CAN CAUSE TURN ON AND TURN OFF TRANSIENTS (NOISE)
+12 Volt(Fused) Constant Power: To Battery (+)
Due to the power requirements of the Amplifier, this connection should bemade
directly to the positive (+) terminal of battery. For safety measures, install anin-line
50 Amp Fuse Holder (not included) as close to the battery Positive (+) terminal as
possible.
With an ampere rating not to exceed the total value of fuses in amp.
Remote Turn-On Input: To Power Antenna output of Vehicle Stereo
This Amplifier is turned＂ON＂remotely when the vehicle＇s stereo is turned＂ON＂.
NOTE
IF YOUR RADIO DOES NOT HAVE A +12 VOLT OUTPUT LEAD WHEN THE RADIO IS TURNED ON, ＂ RMT ＂ TERMINAL ON
THE AMPLIFIER CAN BE CONNECTED TO VEHICLE ＇ S ACCES SORY CIRCUIT THA T IS LIVE WHEN THE KEY IS ＂ ON ＂ .
Chassis
Ground
Chassis
Ground Remote Turn ON
To Power Antenna
FUSE Holder
Near Battery
+ -
BATTERY
1 2
MIL-AMP200BT
4 Channel
N/A
N/A
4 x 20W
250mv - 6V Low Level
N/A
N/A
N/A
N/A
N/A
N/A
40
105
130

RCA high input
X-OVER
Depending on the selected switch setting, the amplifier operates in Fullrange,Highpass or
Lowpass mode.
Aux Input
This unit's bluetooth signal input always has priority right, meanins that even if an Aux cable is
connected to the Aux input, the bluetooth signal is still working. To enable Aux mode, bluetooth signal
has to turned off.
BT LED
Bluetooth state indicator: the indicator will flash slowly if the bluetooth is not paired. After
the unit has been paired, the indicator will be lit continuously.
FUSE
Power protection for the amplifier.
Power LED
The Green color LED indicates that the power is on.
3 4

LOW LEVEL INPUT WIRING
Low-level (RCA) input wiring is preferred for best audio performance. Always use a high-quality
RCA cable for best audio performance.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplifier at the same time!
4-Channel Amplifier
HIGH LEVEL INPUT WIRING
The high level input(s) should only be used when your head unit lacks RCA outputs.If the RCA
outputs are not present, connect the speaker outputs from the receiver to the high level input
connector of the amplifier. Be sure to observe polarity to avoid audio phase problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplifier at the same time!
4-Channel Amplifier
POWER AND SPEAKER WIRING
MIL-AMP200BT
4-channel Amplifier
4-Channel Mode
+
-
-
+
SPEAKER
IMPEDANCE
4 OHMS
SPEAKER
IMPEDANCE
4 OHMS
Connecting To Bluetooth,
1. Connection the amp is going to be largely individualistic to the device. After you turn
the device on, you have a two minute window where it puts out a pairing signal. The
blue LED light will be blinking during this time period if nothing is connected. If
something is, it will be solid blue and that device will need to be disconnected.
2. Because of the two minute timeout, the bluetooth should be wired through a switch
and not to continuous power so that you have a way of reactivating the pairing signal if
need be.
3. While the light is blinking, depending on your device, pull up the bluetooth menu and
find the device in your device menu. You should just then be able to click on it, but if it
prompts for a code it will be “1234”.
4. Disconnection of a paired device is required if you want to pair another device if both
devices are in a 30ft range.

5 6