Milesight UF31 5G DONGLE User manual

UF31
All software & files can be downloaded from
https://www.milesight-iot.com/documents-download/
Cloud App Quick Start Guide
Milesight IoT Co., Ltd. www.milesight-iot.com UF31 5G DONGLE

Table of Contents
1.Packing List………………………………………………………………………………..........................
2.Hardware Introduction………………………………………………………………………………………..
3.LED Indicator Patterns………………………………………………………..............................
4.Fitting Installation…………………………………....................................................……
5.Device Installation……………………………………...................................................…
6.Device Configuration……………………………………....................................…....………
2
3
3
4
5
6
11
www.milesight-iot.com

www.milesight-iot.com www.milesight-iot.com
1. Packing List
Please check the package contents to verify that you have received the items below.
2. Hardware Introduction
3. LED Indicator Patterns
12 131 2 13
If any of the above items is missing or damaged, please contact your sales
representative.
1 × UF31 Device 1 × Power Adapter 1 × Ethernet Cable
2 × Mounting Ear Kits 4 × Wall Mounting Kits 4 × Stubby Cellular Antennas
(Optional)
4 × Antenna Magnetic Mounts
(Optional)
1 × 5G Antenna Box
(Optional)
1 × GPS Antenna
(Optional)
1 × USB 3.0 Cable
(Optional)
1 × DIN Rail Clip
(Optional) 1 × Quick Start Guide 1 × Warranty Card
Cellular Antenna
Connector
LED Indicators
SIM Slot
GPS Antenna Connector
Ethernet Port
Type-C Power
& Console Port
Power Interface
STATUS Power &
System Status
Cellular Status5G
Power offOff
Orange
Green
Red
Off
Green
Orange
Static: power on
Static: functioning properly
SIM card is registering or fails to register on the
network (or there are no SIM cards inserted)
Blinks: SIM card has been registered and is
dialing up now
Static: SIM card has been registered and dialed
up to 5G network
Static: SIM card has been registered and dialed
up to 4G network
Static: system error
DescriptionLED Indication Status

www.milesight-iot.com www.milesight-iot.com
5. Device Installation
4. Fitting Installation
1 4
Step 1: Remove the sheet on the SIM slot, insert the SIM card into the device according to
the direction icon on the device, then fix the sheet on the slot with screw.
If an antenna box is being used, the installation position should be drilled a hole to fix the
antenna box.
Step 2: Rotate antennas into the antenna connectors. Antennas should be installed vertically
always on a site with a good signal.
Step 1: Fix the two mounting ears to both sides of device with screws.
Step 2: Drill 4 holes on the wall according to the mounting ear’s holes and insert the
wall plugs into the wall holes, then fix the device to the wall with mounting screws.
5
1 2
4
3
1 2 3

www.milesight-iot.com www.milesight-iot.com
6. Device Configuration
1 6 17
UF31 provides web-based configuration interface for management. If this is the
first time you configure the device, please use the default settings below:
Step 1: Connect LAN port or Type-C port of device to PC.
Step 2: Configure the IP address of computer manually or automatically. Here
are steps of configuring computer IP address manually based on Windows 10
system:
Step 3: Open a browser and type default IP address to log in the web GUI of the
device.
Step 4: After configuraiton, connect it to terminal devices via Ethernet port or
type-C to provide network access.
Goto“ControlPanel”→“NetworkandInternet”→“NetworkandSharingCenter”,
then click “Ethernet” (May have different names).
Go to “Properties” → “Internet Protocol Version4 (TCP/IPv4) Properties”,
select “Obtain IP address automatically” or “Use the following IP address” to
assign a static IP manually within the same subnet of device.
IP Address: 192.168.1.1
Username: admin
Password: password
Browser: Chrome (recommended)
Milesight 5G

Thank you
for choosing
Milesight Product
1 8
www.milesight-iot.com
Milesight IoT Co., Ltd.
UF31

200g铜版纸+80g双胶纸
UF31
120x85mm
封面覆哑膜（翻页版）
44.005.000144
V1.2
客 户
编 码
机 型
材 质
尺 寸
工 艺
版 本