Milwaukee RBA-2 User manual

IMPORTANT SAFETY
INSTRUCTIONS
WARNING
SYMBOLOGY
Read operator's manual
SPECIFICATIONS
Cat. No............................................................... RBA-2
Maximum offset......................................... 50.8 mm (2")
FUNCTIONAL DESCRIPTION
Compatibility....................... MILWAUKEE®Guide Rails
23
5
6
7
1
4
1.
2. Connection rods
3. egarotswercsbmuhT
4. Handle
5. Anti-tip knob
6. Rail adjustment knob
7. Rod thumb screw
8
8.
9. 5 mm hex wrench
10. Gauge block
11.
12. Guide rail channel
11 9
12
10
ASSEMBLY
WARNING
Assembling
Attaching to Router Base
(M18 FR12, RBA-1)
2.
1. Remove battery pack.
Remove the U-ring from the base, if present.
3.
4.
To reduce the risk of serious injury,
read all safety warnings, instructions,
Always remove battery from tool
before changing or removing
illustrations and specifications provided by the
router and guide rail manufacturer before beginning
work.
Do not dispose of electric tools together
with household waste material. Electric
tools and electronic equipment that have
reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling
facility.
Offset scale rod Bar (for M18 FR12,
RBA-1)
M18 FTR conversion
parts
accessories. Only use accessories specifically
recommended for this tool. Others may be
hazardous.
Slide the connection rods equally into the accessory
holes of the base until the bar is flush against the
router base.
Move the two thumb screws from storage into the
threads of the router base to secure the rods to the
router base.
1
Attaching to a Guide Rail
1. Remove battery pack.
2.
3. Loosen the rail adjustment knobs.
4.
5.
6. Engage the anti-tip feature by
pressing the button in and rotating
the anti-tip knobs.
Cat. no.: RBA-2
1/2" ROUTER TRACK ADAPTER
Assemble the track adapter, as shown.
Place the track adapter onto the guide rail, aligning
the channel on the track adapter with the guide rail
channel.
Check for play between the track adapter and guide
rail.
Adjust both rail adjustment knobs to remove play
between track adapter and guide rail
while still allowing the track adapter
to slide smoothly along the guide rail.
For best results, the guideclearance
of the router must be very small.

2
1. battery pack.
2. rod thumb screws.
Remove
Loosen the
3.
4.
Using
1. Remove battery
the Gauge Block
pack.
2. on the workpiece.cut lineMark the
3. Select a bit and note the bit diameter.
4. rail onSet the the workpiece.guide
5. block against the guide rail.gaugePlace the
6.
7. Secure the guide rail to the workpiece.
8. Insert the bit into the router.
9. Attach the router to the guide rail.
10.
pack.1. Remove battery
2.
3.
4.
5. Reassemble the rod assembly.
7. Place the track adapter onto the guide rail.
6. Insert the rod assembly into the track adapter.
8.
9.
Offset
Using the offset scale, slide the track adapter away
from the router base to the desired offset (up to
50.8mm (2")).
Adjust the guide rail and gauge block until the bit
diameter edge marking of the gauge block (that
matches your bit diameter) is parallel to the cut line.
Set the guide rail offset to 0 so the router is flush up
against the track.
Remove the rod assembly from the track adapter.
Disassemble the rod assembly (Connection rod
screws are T20; Offset scale rod is T10).
Replace the standard adapter plate with the laminate
trimmer adapter plate.
Tighten both rod thumb screws to lock the offset.
Converting Track Adapter for use with
M18 FTR Laminate Trimmer
Position laminate trimmer against laminate trimmer
adapter plate (aligning slot in plate with matching
boss on trim router).
Tighten the bolt with washer using the 5 mm hex
wrench to secure trim router to guide rail adapter.

961014800-01(A)
WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy DutyTM.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE®dealer.
For a list of MILWAUKEE®dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928)
or visit milwaukeetool.com.au/milwaukeetool.co.nz.
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold by authorised dealers in Australia and New Zealand.
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN CHINA
PRINTED IN CHINA
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
26 - 40 Nina Link, Dandenong South,
Victoria, 3175, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand