Zero & Unit setting button 31
42
QD PINOUT
PANEL DESCRIPTION / DIMENSIONS
3 ½ digit LED display
Display the measured
pressure value. each
setting mode and error
code.
PR-0064D 2021/10 Printing
300
We reserve the right to change the specification without prior notice.
Setting Button
kPa
kPa
MP23
MINDMAN INDUSTRIAL CO., LTD.
www.mindman.com.tw
MP-A1：Mounting bracket (BT-1)
MP-A2：Mounting bracket (BT-2)
MP-B1：Panel adapter (PA-A)
MP-C1：Panel adapter + Front protective lid (PA-B)
MP-D1：WIth M8, 4Pin female connector (M84R-W0085-2M)
For your safety, please read the following before using.
Do not use corrosive or flammable gas or liquid with this product.
Please use within the operating pressure range. Do not apply pressure beyond recommended maximum pressure, permanent damage to the pressure
sensor may occur.
Do not drop, hit or allow excessive shock. Even if switch body appears undamaged, internal components may be broken and can cause malfunction.
Turn power off before connecting wiring. Wrong wiring or short circuit will damage and / or cause malfunction.
Do not use in environment containing steam or oil vapor.
This product is not explosion-proof rated. Do not use in atmosphere containing flammable or explosive gases.
Wiring for pressure sensor should avoid power source line and high voltage line. If use in the same circuit, noise may cause malfunction.
1
2
3
4
5
6
7
Display pressure range
Withstand pressure
Fluid
Power supply voltage
Current consumption
Display
Indicator accuracy
-0.100 ~ 1.000 MPa
Filtered air, Non-corrosive/Non-Flammable gas
12 to 24V DC ±10%, Ripple (P-P) 10% or less
≦55mA
3½digit LED display (Red) (Sampling rate: 5 times/sec.)
±2% F.S. ±1 digit (ambient temperature: 25 ±3°C)
SPECIFICATIONS
-100.0 ~ 100.0 kPa
(Positive)(Compound)
Ambient temp. range
Ambient humidity range
Withstand voltage
Enclosure
Insulation resistance
Vibration
Shock
Temperature characteristic
Port size
Lead wire
Weight
Operation/Storage: 35 ~ 85% RH (No condensation)
1000V AC in 1-min (between case and lead wire)
IP40
50MΩ(at 500V DC, between case and lead wire)
980m/s2 (100G), 3 times each in direction of X, Y and Z
±2% F.S. of detected pressure (25°C) at temp. Range of 0~50°C
F1:Rc1/8"; F2:NPT1/8"; F3: G1/8"(BSPP)
Ø4 Oil-resistance cable ( PVC ) - 26 AWG ( 0.15 mm2) - 2 cores
Operation: 0 ~ 50°C, Storage: -20 ~ 60°C (No condensation or freezing)
Approx. 102g (with 2 meter lead wire), Approx. 68g (with M8, 4Pin male connector)
Total amplitude 1.5mm, 10Hz-55Hz-10Hz scan for 1 minute, two hours each direction of X, Y and Z
Environment
300 kPa 1.5 MPa
MP23C- - MP23P- -
kPa
MPa
kgf/cm2
bar
psi
mmHg
inHg
mmH2O
Set pressure
resolution
0.1
0.001
0.001
-
0.01
-
0.001
0.01
0.01
0.1
-
-
-
1
0.1
0.1
ORDERING INFORMATION
CIRCUIT WIRING DIAGRAM
DC(-)
(Blue)
DC(+)
(Brown)
DCDC
12-24V
Main circuit
*Pressure display only, no switch output function.
Pressure Range Cable Length/Connector
Pressure Port
C：Compound
(-100.0~100.0 kPa)
P：Positive
(-0.100~1.000 MPa)
Blank：With 2 meter cable
QD：With M8, 4Pin male connector
F1：Rc1/8”
F2：NPT1/8”
F3：G1/8"(BSPP)
Optional Parts
INSTALLATION
This product has two inlet pressure ports, select
the one most convenient for installation.
Please plug the unused inlet port with supplied
port plug. Use seal tape to prevent pressure leak.
1.
2.
Unit:mm
Bolt(screw)
MP23C-F1-
(1) Brown (+)
(2) Not used
(3) Blue (–)
(4) Not used
