minkaAire Craftsman F840 User manual

U.S. Patents: D579,097; D579,098; D579,103; D581,512; D583,044

This product is protected by United States Federal and/or State Law, including Patent, Trademark and/or Copyright laws.
Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.

CONTENTS
1
2
3
4
5
6
7
8
9
10
11
12
13
SAFETY RULES
PACKAGE CONTENTS
INSTALLING THE FAN
HANGING THE FAN
ELECTRICAL CONNECTIONS
INSTALLING THE WALL TRANSMTTER
FINISHING THE INSTALLATION
BLADE AND LIGHT CAP INSTALLATION
INSTALLING THE LIGHT BULBS & GLASS SHADES
OPERATING THE REMOTE CONTROL/WALL CONTROL
CARE OF YOUR FAN
TROUBLESHOOTING
SPECIFICATIONS
1151W. Bradford Court, Corona,CA 92882 For Customer Assistance Call: 1-800-307-3267

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors which can not be built into this product. These factors must be
supplied by the person(s) installing caring for and operating the unit.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L LISTED OUTLET BOX OR SUPPORTING
SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX IN CONJUCTION WITH THE
LOCK WASHERS PROVIDED WITH THE FAN. MOST OUTLET BOXS COMMONLY USED FOR FAN SUPPORT OF LIGHTING FIXTURES ARE NOT
ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDER WHILE INSTALLING, BALANCING THE BLADES OR CLEANING THE
FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE UC7067RY SOLID-STATE SPEED CONTROL WITH UC9040T WALL
CONTROL ONLY.
WARNING
NOTE: READ AND SAVE ALL INSTRUCTIONS!
ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a 190 watt limiting device. If lamping exceeds 190 watts, the ceiling
fan’s light kit will shut off automatically.

PACKAGE CONTENTS
Unpack your fan and check the contents.
You should have the following items:
1. Fan blades (5)
2. Mounting bracket
3. Canopy
4a. Standard downrod assembly
4b. Minimum-length downrod (for close
to ceiling mounting only)
5. Coupling cover
6. Glass shades (3)
7. Motor assembly (1)
8. Blade holders (5)
9. Light cap
10. Light kit assembly (1)
11. Receiver with 6 wire nuts
12a.Wall transmitter Incl,2 Mounting
Screws and 3 Wire Nuts.
12b.Wall Plate w/2 Mounting screws
13. Extra wall plate
14. Bulbs (3)
15. Balancing Kit
A. Mounting Hardware:
#8-32X3/4” Machine scews (2 pcs)
#8X1 ” Wood screws (2 pcs)
Flat washers (2 pcs)
Wire nuts (4 pcs)
B. Blade Attachment Hardware:
#8-32X8 Screws (16 pcs)
S.S Washers (16 pcs)
C. Bracket Holder Hardware:
1/4” X 1/2” Screws with lock washers (11 pcs)
D. Downrod rubber cover
E. Finial
1
2
2
15

REMEMBER to turn off the power.Follow the steps below to hang your fan
properly:
Step 1. Secure the hanger bracket to the ceiling outlet box using screws
included with your outlet box, lock washers included with the fan.(Fig 5)
Step 2. Loosen the two set screws and remove the hitch pin and lock pin
from the top coupling of the motor assembly.(Fig 6)
Step 3. Remove hanger ball from downrod assembly by loosening set
screw,removing the cross pin,and sliding ball off rod.(Fig 7)
Step 4. Carefully feed fan wires up through the downrod (Fig 8).
Thread the rod into the coupling, line up holes and replace lock pin and
hitch pin.Tighten set screws.
Step 5. Slip coupling cover, and canopy onto downrod (Fig 8). Carefully
reinstall hanger ball onto rod being sure that cross pin is in the correct
position,set screws are tighten and wires are not twisted.
Step 6. Place downrod rubber cover onto the hanger ball (Fig 9)
Step 7. Now lift motor assembly into position and place hanger ball
into hanger bracket.Rotate until the check groove has dropped into the
registration slot and seats firmly. (Fig 10) Rod should not rotate if this
is done correctly.
HANGING THE FAN
4
WARNING: All of the parts, hardware and components such as the hanger
bracket and hanger ball have been provided for your safety and the proper
installation of your new ceiling fan. The use of other parts, hardware or
components not supplied by Minka Aire® with the fan will void the Minka
Aire® Warranty.