Minolta MN60WP User manual

1. About Your Camera
1
About this Manual
Congratulations on purchasing the Minolta MN60WP Waterproof Camera!
The contents of this manual are subject to change without notice. Note that the
may differ
somewhat from the screens and configuration of the actual camera.
Copyright
This manual contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of Elite
Brands Inc. © 2023.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)
This device may not cause harmful interference and
(2)
This device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Warning
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment must be installed and operated in
accordance with provided instructions and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must
be provided with antenna installation instructions and transmitter operating

1. About Your Camera
2
conditions for satisfying RF exposure compliance.
FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.4 W/kg
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Safety and Handling Precautions
Camera Information
Do not disassemble or attempt to service the camera yourself.
Do not expose the camera to moisture, or extreme temperatures.
Allow the camera to warm up when moving from cold to warm temperatures.
Do not touch and put pressure on the camera lens.
Do not expose the lens to direct sunlight for extended periods.
Do not use abrasive chemicals, cleaning solvents or strong detergents to clean
the product. Wipe the product with a slightly damp soft cloth.
Do not use the flash or LED Light near a person's eyes to prevent possible eye
injury.
To prevent you from falling over or resulting in traffic accident, please do not
use the camera while you are walking, driving or riding a vehicle.
Please handle the camera strap with care, and never place the strap around
the neck of an infant or child. Wrapping the strap around a neck may cause
suffocation.
Do not subject the LCD screen to impact.
To prevent the risk of fire or electric shock, do not expose the inside of this
product to rain or moisture.
Battery Information
Turn off the camera before installing or removing the battery.
Use only the provided batteries or type of battery and charger that came with
your camera. Using other types of battery or charger may damage the device
and invalidate the warranty.
Inserting the battery upside down can cause damage to the product and
possibly cause an explosion.
When the camera is used for an extended period of time, it is normal for the
camera body to feel warm.
Download all pictures and remove the battery from the camera if you are going
to store the camera for a long period of time.
Risk of explosion if battery is replaced by an incorrect type. Dispose of used

1. About Your Camera
3
batteries according to the instructions.
Please keep the batteries out of the reach of children to prevent from
swallowing the batteries, which might cause poisoning.
If the battery's color or shape changes in any way, stop using the battery
immediately.
USB Adaptor Information
Do not expose the adapter to high temperatures or moisture places. Otherwise, it
may cause fire or electric shock.
Do not attempt to repair, disassemble, change or transform the adapter.
Avoid sudden changes in temperature, which may cause condensation on the
Do not touch the plug with wet hands. Otherwise, it may cause electric shock.
Do not use the travel voltage converter or AC/DC power inverter. Otherwise, it
may cause damage, overheating, malfunction or fire to the camera.
Waterproof and Dustproof Information
The waterproof and dustproof performance described do not guarantee that
the camera will remain completely waterproof or free from damage and
trouble under all conditions.
Do not subject the camera to excessive shock, Vibration or pressure by
dropping it, hitting it or placing a heavy object on it. Failure to observe this
precaution could deform the camera, cause water to seep inside, or damage
the airtight seals, resulting in camera malfunction.
The battery door must be closed securely and the lock engaged in order for
the camera to be waterproof. Failure to do this can allow water to enter the
camera and damage it.
The camera can shoot images underwater at a depth of 3m (10ft) for up to
60 minutes.
Do not drop the camera, strike it against a hard object such as a rock, or
throw it against a water surface.
Do not subject the camera to shock when using it underwater.
Do not expose to depths greater than 3m (10ft) underwater.
Do not continuously use the camera underwater for 60 minutes or more.
Do not insert a wet memory card or battery in the camera.
Do not open the battery cover when the camera or your hands are wet. Doing
so may cause water to seep inside the camera or result in camera
malfunction.
Do not open the battery cover underwater.

1. About Your Camera
4
If moisture such as water droplets adheres to the outside of the camera or
inside of the battery cover, immediately wipe it
If a foreign substance adheres to the outside of the camera or inside of the
battery cover, immediately remove it with a soft cloth.
Do not leave the camera in cold conditions or hot conditions of 40°C (104°F)
or more for a long period of time.
When using the camera underwater, make sure the water temperature is from
0°C-40°C (32°F to 104°F).
Do not use the camera in hot springs.
Before Using the Camera Underwater
Check the items below before using the camera underwater.
Make sure that there are no foreign substances inside the battery cover.
Make sure that the waterproof packing of the battery cover is not cracked or
deformed.
Make sure that the battery door
lock is in the LOCK position.
Failure to follow these steps can result in damage to the camera.
Notes about Opening and Closing the Battery Door
Make sure the camera and your hands are not wet.
Make sure that there are no debris inside the battery-chamber or memory card
slot.
lock position.

1. About Your Camera
5
To Unlock the Battery Door
Unlock the battery door by sliding the battery door notch away from the opening.
Use a fingernail or other pointy object when sliding the latch to get a better grip.
To Lock the Battery Door
Press down on the end of the battery door where the latch is located until the
battery door is completely flat and a click is heard.
Precautions When Cleaning
Do not puncture the microphone or speaker openings with a sharp implement.
If the inside of the camera is damaged, the waterproof performance will
deteriorate.
Do not use soap, natural detergents, or chemicals such as benzene for
cleaning.
Do Not Apply Strong Impact to the Camera
The product may malfunction if subjected to strong shock or vibration. In
addition, do not touch or apply force to the lens.
Avoid Sudden Changes in Temperature
Sudden changes in temperature, such as when entering or leaving a heated
building on a cold day, can cause condensation to form inside the device. To
prevent condensation, place the device in a carrying case or a plastic bag
before exposing it to sudden changes in temperature.
Keep Away from Strong Magnetic Fields
Do not use or store this device in the vicinity of equipment that generates strong
data or camera malfunction.

1. About Your Camera
6
Do Not Point the Lens at Strong Light Sources for Extended Periods
Avoid pointing the lens at the sun or other strong light source light sources for
extended periods when using or storing the camera. Intense light may cause
the image sensor to deter
before Removing or Disconnecting the Power
Source or Memory Card
Do not remove the battery while the product is on, or while images are being
saved or deleted. Forcibly cutting power in these circumstances could result in
loss of data or cause damage to the memory card or internal circuitry.
Notes about the LCD Screen
The LCD Screens are constructed with extremely high precision; At least
more than 0.01% being missing or
defective. Hence, while these displays may contain pixels that are always lit
Images viewed on
lighting.
Do not apply pressure to the LCD screen, as this could cause damage or
malfunction.
The Battery
Precautions for Use
Note that the battery may become hot after use.
Do not use the battery at ambient temperatures below 0°C (32°F) or above
40°C (104°F) as this could cause damage or malfunction.
If you notice any abnormalities such as excessive heat, smoke, or an unusual
smell coming from the battery, immediately discontinue use and consult your
retailer.
After removing the battery from the camera or optional battery charger, put
the battery in a plastic bag, etc. in order to insulate it.
Charging the Battery
Check the battery level before using the camera and replace or charge the
battery if necessary.
Charge the battery indoors with an ambient temperature of 5°C (41°F) to
35°C (95°F) before use.
A high battery temperature may prevent the battery from charging properly or
completely, and may reduce battery performance. Note that the battery may
become hot after use; wait for the battery to cool before charging. When
charging the battery inserted into this camera using the Charging AC Adapter

1. About Your Camera
7
or a computer, the battery is not charged at battery temperature below 5°C
(41°F) or above 55°C (131°F).
When the battery is between 45°C (113°F) - 55°C (131°F), the chargeable
capacity may decrease.
Do not continue charging once the battery is fully charged as this will result in
reduce battery performance.
The battery temperature may increase during charging. However, this is not a
malfunction.
Using the Battery When Cold
On cold days, the capacity of batteries tends to decrease. If an exhausted
battery is used at a low temperature, the camera may not turn on. Keep spare
batteries in a warm place and exchange as necessary. Once warmed, a cold
battery may recover some of its charge.
Recycling Used Batteries
Replace the battery when it no longer holds a charge. Used batteries are a
valuable resource. Please recycle used batteries in accordance with local
regulations.
Cleaning After Using the Camera Underwater
Follow the procedure below to rinse the camera with fresh water within 30
minutes after using it under saltwater or at the beach.
1.
ter.
2.
remove any foreign substances from the camera.
3.
When the cameras is immersed in the water, a few air bubbles may come
out from the water drain holes of the camera such as openings in the
microphone or speakers. This is not a malfunction.
4.
-
ventilated and shady place.
5.
Place the camera on a dry cloth to dry it.
6.
Do not dry the camera with hot air from a hair dryer or clothes dryer.
7.
After making sure that there are no water droplets on the camera, open the
remaining on the waterproof packing or inside the camera.
If the cover is closed when the inside is wet, this could cause
condensation or a malfunction.
Cleaning After Using the Camera in Conditions Other than Underwater
Use a blower to remove any dust or lint that adheres to the lens, monitor or

1. About Your Camera
8
with a blower, gently wipe the parts with a soft dry cloth. If you wipe with too
much pressure or with a rough cloth, it may damage the camera or cause a
malfunction.
Storage
If you do not intend to use the camera for an extended period, remove the
battery and avoid storing the camera in any of the following types of locations:
Places that are poorly ventilated or subject to humidity of over 60%
Place exposed to temperatures above 50°C (122°F) or below -10°C (14°F).
television or radios.
To prevent mold or mildew, take the camera out of storage at least once a
month, and turn it on and release the shutter a few times before putting it away
again.

9
1.1 Camera Interface
1. Shutter 10. LED Indicator
2. Switch Screen 11. Zoom In
3. Power 12. Up | LED Light On/Off
4. LED Light 13. Down | Delete |
Record Audio On/Off
5.
Microphone
14.
Menu
6.
Speaker
15.
Mode
7.
Lens
16.
O
K
| Zoom Out
8.
Front LCD Screen
17. Tripod Mount
9. Rear LCD Screen 18. Battery Cover/Lock
8 7
1
2 3 4 5
6
14
12
13
9 10 11
16
15
18 17

10
1.2 Button Function Description
Function Description
Power Press for 3 seconds to power on or off.
OK | Zoom Out
In Settings: Tap to enter menus and confirm selected
setting.
In Video or Photo: Press and hold to zoom out.
In Playback:
Tap to play and pause recorded videos.
Zoom In In Video or Photo: Press and hold to zoom in.
Mode Tap to cycle between Photo, Video and Playback modes.
Menu Tap to access the setting menus.
Up | LED Light
In Video or Photo: Press to turn the LED light On and
Off.
In Playback: Press to go to the previous image.
In Settings:
Press to select desired setting.
Down | Delete |
Record Audio
In Video or Photo: Press to turn audio recording on and
off.
In Playback: Press to go to the next image. Press and
hold to access the delete menu for the current file.
In Settings:
Press to select desired setting.
Shutter In Photo: Tap to capture a photo.
In Video:
Tap to start and stop recording.
Switch Screen Switches the LCD screen that is powered on.
Tripod Mount Mount port for attaching to a tripod nut.
Battery Door Door to cover the battery compartment and memory card
slot.
Speaker Built-in speaker output for playback of video files when
audio recording is enabled.
Lens Front capture device for all video and photo.

11
1. To Open the Battery Door
Unlock the battery door by sliding the battery door notch away from the
opening. Use a fingernail or other pointy object when sliding the latch to get a
better grip. The battery door will flip up automatically when the latch is fully
opened.
1. Installing the Battery
Insert the lithium-ion battery into the battery compartment with the metal
contacts facing the inside of the camera. The battery can only inserted one
way.
1. Installing the Memory Card
Insert the included MicroSD memory card to record and store your videos and
photos. When the battery is low, media stored on the memory card will not be
erased. Please insert the MicroSD memory card by following the steps below:
1. Open the battery door by following the diagram above.
2. Insert the memory card. Ensure that the metal contacts are inserted first.

12
Push the memory card down until you hear an audible click.
The memory card can only be inserted in one way. Do not force the
card in if it will not go in smoothly.
3. Close the memory card door by pushing it down and a click is heard from
the latch.
4. To remove the memory card, simply push in and the card will eject back out.
NOTE: After closing the battery door, make sure that the door
is closed securely and the lock engaged. Failure to do this can
allow water to enter the camera and cause damage.
NOTE:
Please format the memory card before using the camera
(Caution, this will erase all data on the card).
Do not remove or insert the memory card when recording. It
may damage the card or cause data loss.
Memory card rating must be Class 10 or above.

13
1. To Lock the Battery Door
Press down on the end of the battery door where the latch is located until the
battery door is completely flat and a click is heard. The battery door is fully
locked once the latch clicks into place.
1. Charging the Battery
Connect your camera to the included AC adaptor with the USB cable
provided for charging. Insert the small end of the USB plug into the camera s
port under the battery door, and the larger end in to the included AC adaptor.
While charging the LED indicator light will light up solid red, when finished
charging the light will turn off.
1. Powering the Camera On/Off
Hold the POWER button for 3 seconds to power the camera on. To power
the camera off, press and hold the POWER button for a further 3 seconds.
If the camera
screen and it will automatically shut down within a few seconds to prevent
memory corruption or loss.
1. Switching Modes
Press the MODE button to see the eight Photo and Video modes. Use the
UP or DOWN buttons to select your desired mode, then press the OK
button to enter that mode. The corresponding mode will be displayed in
the top left corner of the screen. To enter Playback mode, press the
MODE button to enter the mode selection screen, then press the MODE
button again.
1. Connecting to a Computer
Your camera can connect to a computer to transfer photo and video files for
viewing and editing, or use the camcorder as a web cam. To connect the

14
camcorder to your computer, open the battery door on the bottom of the
camera to access the USB port. Insert the small end of the USB plug into the
be
will function as a web cam. Use the UP or DOWN buttons to select your
desired mode and press the OK button to enter into that mode.
1. Using the Zoom Function
This camera has a digital zoom function. To operate the zoom function,
press and hold the ZOOM IN button to zoom in closer to the subject, and
press and hold the ZOOM OUT button zoom away from the subject.
1.1 LED Light
Your camera is equipped with an LED light that can be activated to help light
dark scenes. To activate the LED light, simply press the UP button while in
any photo or video modes. Press the UP button again to turn off the light.

15
1.1 Screen Icons
The meaning of the icons shown on the LCD screen in each mode can be
found below.
Icon Description
Photo Mode
Interval Photo Mode
Burst Photo Mode
Self-Timer Photo Mode
Video Mode
Slow Motion Mode
Loop Recording Mode
Time Lapse Mode

. Using Your Camera 16
2. Using the Camera
2.1 Photo Shooting
To enter Photo mode, power the camera on and press the MODE button to
access the mode selection screen and use the UP or DOWN buttons to select
Photo and press the OK button to enter that mode.
1.
Line up your shot by looking at the LCD screen to see what is in the shot.
2.
Hold the camera steady and press the SHUTTER button to capture a
photo.
3.
The number of photos that can be captured at a particular resolution will
be displayed in the top of the screen.
4.
The number of pictures remaining will be 0 if there is no memory card
Memory Full
be shown at the screen when the memory card is full.
5.
The number of remaining photos is determined by the selected photo
resolution. The higher the photo resolution, the lower the number of photos
you are able to be save to the memory card. Before capturing any photos,
you can select a preferred photo resolution.
The front LCD screen can be used to take selfies. Simply press the SWITCH
SCREEN button and the front LCD screen will turn on. Then use the camera
as normal. Press the SWITCH SCREEN button to turn the rear LCD screen
back on.
Note: Only one LCD screen is active at a time, when one of the screens is off,
this is not a malfunction.
2.1.1 Photo Size
This function sets the photo resolution. The higher the resolution, the greater
the photo quality and the larger the file size of the photo.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select Photo Size using the UP or DOWN buttons.
4. Press the OK button to enter the Photo Size submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected resolution (48MP, 30MP, 24MP, 20MP,

17
16MP, 13MP, 12MP, 8MP).
6. Press the MENU button twice to exit the settings menu.
2.1.2 White Balance
White Balance changes the color of light in your pictures, making it seem
warmer or cooler depending on how the light you're shooting in affects the
frame.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select White Balance using the UP or DOWN buttons.
4. Press the OK button to enter the White Balance submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (Auto, Sunny, Cloudy,
Incandescent, Florescent).
6. Press the MENU button twice to exit the settings menu.
2.1.3 Color Effect
This function sets the color filter effect of a photograph.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select Color Effect using the UP or DOWN buttons.
4. Press the OK button to enter the Color Effect submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (Normal, Black and White, Negative,
Retro, Red, Green, Blue).
6. Press the MENU button twice to exit the settings menu.
2.1.4 Exposure
This function adjusts the frame brightness in your photograph.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select Exposure using the UP or DOWN buttons.
4. Press the OK button to enter the Exposure submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (-3, -2, -1, 0, +1, +2, +3).

18
6. Press the MENU button twice to exit the settings menu.
2.1.5 Metering
Metering mode refers to the way in which a camera determines the appropriate
exposure (quantity of light reaching the camera lens). Spot metering will only
base the exposure setting on a very small area of the scene. Center metering
will use the light from the center of the LCD and the Multi setting measures the
light at several points on the screen.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select Metering using the UP or DOWN buttons.
4. Press the OK button to enter the Metering submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (Multi, Center, Spot, Matrix).
6. Press the MENU button twice to exit the settings menu.
2.1.6 Image Sharpness
This function adjusts the visible detail of a photograph.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select Sharpness using the UP or DOWN buttons.
4. Press the OK button to enter the Sharpness submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (Sharp, Normal, Soft).
6. Press the MENU button twice to exit the settings menu.
2.1.7 Long Exposure
This function allows you to set the amount of time that the camera's shutter is
left open. The resulting image captures the trail of moving objects in front of
the camera, while showing still elements razor sharp.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select using the UP or DOWN buttons.
4. Press the OK button to enter the Long Exposure submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK

19
button to confirm your selected option (Auto, 2 Seconds, 5 Seconds, 10
Seconds, 15 Seconds, 20 Seconds, 30 Seconds).
6. Press the MENU button twice to exit the settings menu.
2.1.8 ISO
This function adjusts the light sensitivity in your photograph.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select using the UP or DOWN buttons.
4. Press the OK button to enter the ISO submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (Auto, 100, 200, 400, 800, 1600,
3200, 6400).
6. Press the MENU button twice to exit the settings menu.
2.1.9 Time Stamp
This setting allows you to imprint a date & time onto your captured image files.
Once an image file is captured with the imprint, the imprint cannot be
removed.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select using the UP or DOWN buttons.
4. Press the OK button to turn Time Stamp on and off, a check mark
indicates that the feature is active.
5. Press the MENU button twice to exit the settings menu.
2.1.10 Field of View
This function lets you set the field of view that the camera captures.
1. In Photo Mode press the MENU button.
2. Press the OK button to enter the Photo mode settings.
3. Select using the UP or DOWN buttons.
4. Press the OK button to enter the Field of View submenu.
5. Press the UP or DOWN buttons to navigate the menu, and press the OK
button to confirm your selected option (Wide, Standard, Narrow).
6. Press the MENU button twice to exit the settings menu.