Miro TD490 User manual

miro TD490 Manual
miro Displays GmbH · TRIFORUM · Haus A1 · Frankfurter Str. 233 · D-63263 Neu-Isenburg · Tel.[phone] (0.12 Euro/Min) · Fax [phone] · e-mail:[email protected]

TABLE OF CONTENTS
INTRODUCTION
FCC Compliance Statement..............................................................i
Safety Instructions ..........................................................................iii
General Information..........................................................................1
Equipment Checklist ........................................................................2
Monitor Features ..............................................................................3
GETTING STARTED
Installation ........................................................................................4
Installation VESA Wall Mount ..........................................................6
Control Buttons ................................................................................7
On-Screen Display ..........................................................................8
ON-SCREEN CONTROLS
Menu Descriptions............................................................................9
REFERENCE
Power Management........................................................................11
Plug & Play ....................................................................................11
Timing Guide ..................................................................................12
Timing Table ..................................................................................13
Pin Assignment ..............................................................................14
Specifications..................................................................................15
Troubleshooting..............................................................................16

FCC COMPLIANCE STATEMENT
Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interferen-
ce in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordan-
ce with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interfe-
rence to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification to this equipment. It is the responsibilities of the user
to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or
moisture. Dangerously high voltages are present inside the monitor. Do
not open the cabinet. Refer servicing to qualified personnel only.
i

SAFETY INSTRUCTIONS
HANDLING
Due to its fragile glass panel, this monitor must be handled with caution
and not exposed to impact or shock. Never touch the display area or
rub it with a hard stiff object or tool, as the panel is easily scratched.
CLEANING
The display area is highly prone to scratching. Do not use ketone-type
cleaners (i.e. acetone), ethyl alcohol, toluene, ethyl acid or methyl
chloride to clean the panel. Doing so may result in permanent damage.
Water, IPA (Iso Prophyl Alcohol) and Hexane are safe cleaners.
Do not allow oil or water to penetrate the display, as droplets cause
staining and discoloration with time.
Keep food particles and fingerprints away from the display area at all
times.
STORAGE
Store the monitor in a dark place away from sunlight and ultraviolet
(UV) radiation, as air bubbles may develop within the glass panel with
time.
Do not store the display in temperatures higher than 60°C/140°F or
humidity greater than 85%. Avoid condensation.
ii iii

GENERAL INFORMATION
Your new LCD monitor incorporates the latest state-of-art color Liquid
Crystal Display (LCD) technology providing a wider viewing angle with
higher contrast ratio for IBM compatible PC and Apple Macintosh.
Your new LCD monitor has many advantages : safe from electromagnetic
wave, lights, sharps and slims. This makes the monitor extremely suitable
in the environment of administration, transportation system research, etc.
Your new LCD monitor is designed for Analog and Digital (DVI) input
support.
Your new LCD monitor is a type monitor or VESA-compatible wall
mountable type.
Your new LCD monitor does not emit any X-ray radiation and the
magnetic emission greatly reduces the eyestrain. Moreover, our On
Screen Controls on the bottom of the panel provide flexibility with simple
controls. You can use these controls to adjust the display as you desire.
Your new LCD monitor incorporates an active TFT module. It has a
1280 x 1024 pixel resolution, high contrast, wide viewing angle and colors
up to 16.7M.
SAFETY INSTRUCTIONS
CAUTION
1. Do not open any covers on the monitor. No user serviceable
parts are inside.
2. In an emergency, disconnect the AC power plug.
3. To avoid electrical shock, disconnect the power cord from the AC
adapter before connecting the signal cable to the computer.
4. Keep away from liquids and flame. Do not immerse this monitor
in water or any other liquid. Do not use this device in excessively
hot conditions.
5. Handle the power cord with care. Do not bend the power cord
excessively or place heavy objects on it. Do not use a damaged
power cord, as doing so can result in fire or electrical shock
hazards. When disconnecting the power cord, always grasp the
plug, not the cord.
6. The liquid crystals in the display panel contain several irritants. If
the panel is damaged or broken, do not allow the liquid to come in
contact with skin, eyes, or mouth. If you come in contact with the
liquid, flush the affected area with running water for at least
15 minutes, then consult a doctor.
7. Handle this monitor with care when moving it. When lifting the
monitor, support it with one hand holding the stand, and one
hand holding the LCD screen.
8. Always disconnect the power cord when moving this monitor.
9. Do not lay this monitor in a horizontal position when operating.
10. Unplug the unit during a lightening storm or when it will not be used
for long period of time. This will protect the monitor from damage
due to power surges.
iv 1

MONITOR FEATURES
* Supports Analog IBM compatible PC, Apple MacintoshTM (Adapter
optional)
*Supports DPMS for monitor power management
*Supports DDC1/2B
*Digital and Analog Input
*USB 2.0 Hub - 1up 4down
*Built-In Speakers, 2W x 2
*On Screen Control : Auto Image Adjust, Contrast, Brightness,
Input Selected, Focus, Clock, H-Position, V-Position, Language,
Scaling Mode, Color Temperature (6500°K; 7800°K), RGB Color
Temperature, Recall, Exit
*Built-in color active matrix TFT (Thin Film Transistor) Liquid Crystal
Display (LCD) that uses amorphous silicon TFTs as a switching device
*max. Resolution for analog input: 1280 x 1024 @ 85Hz
*max. Resolution for digital input: 1280 x 1024 @ 75Hz (DVI-D)
*Color : up to 16.7 M Color support
*Dot pitch : 0.294mm(H) x 0.294mm(W)
*Analog input scanning frequency 24kHz ~ 93kHz (H), 55Hz ~ 85Hz (V)
*Digital input scanning frequency 24kHz ~ 83kHz (H), 55Hz ~ 85 Hz (V)
*Universal power supply : AC 100 - 240V allowed
*Power consumption Normal : 65 Watt Max.
Stand-by : 3 Watt Max.
Off : 2 Watt Max.
*Outside dimension : 432mm(W) x 440mm(H) x 198mm(D)
*Weight (net) : 5.9kg
EQUIPMENT CHECKLIST
Before operating your display, please check to make sure that all of the
items listed are present in your package:
• Color TFT LCD Monitor
• Accessory Box:
1. AC to DC Adapter & Power Cord
2. 15-pin D-SUB cable
3. DVI Cable
4. USB Cable
5. Audio Cable
6. This manual
Power Requirements
The monitor is equipped with an auto-sensing power supply for
voltage ranging from 100-240VAC, 50/60Hz.
Confirm the line voltage designation then attach the power cable
to the power jack.
Save the carton and packaging materials in case you need to relocate the monitor.
2 3

INSTALLATION
Follow these instructions to install and remove the swivel base.
INSTALL: REMOVE:
Preparing to install the cables.
1. Remove the wall mounting hole cover.
2. Remove the cable cover.
4 5
INSTALLATION
Follow these steps to install the monitor
1. Before you connect the cables, make sure the monitor and system
unit power switches are OFF.
2. Plug one end of the 15-pin signal cable to the rear of your system
and the other end in the “Analog” video signal connector of LCD
monitor. The adapter may be required for certain Apple Macintosh
computers. Tighten the two screws on the cable connector.
3. Connect one end of the 24-pin DVI cable to the back of the monitor
and connect the other end to the computer’s DVI port (requires a
video card with DVI port).
4. Connect the audio cable between the monitor’s audio input and the
PC’s audio output.
5. Attach the female end of the power cord to the adapter, then plug the
adapter connector to the power “DC-IN” jack of the LCD monitor.
Plug the male end of power cord into an AC wall outlet.
6. Connect a headphone to the monitor’s headphone jack (headphone
not included).
7. Turn on your computer and your LCD monitor.
1. External Adapter
2. 15-pin D-Sub Cable
3. DVI Cable
4. Audio Cord
5. Power Cable
6. Headphone
7. USB Cable
8. Press down on the stand and gently adjust
the monitor to a suitable viewing angle.
Please note that this monitor can only be
tilted forward to 5° and backward to 20°. To
prevent damage to the monitor, do not press
the screen over its tolerant angles.

INSTALLATION
VESA WALL MOUNT
This monitor can be attached to a wall mounting arm (not included).
Disconnect power before performing this procedure. Follow these steps:
1. Remove the VESA cover from the monitor.
2. Remove the stand rear cover from the base.
3. Unplug the connector.
4. Pull out the cable from the hook of base.
5. Support the base and remove the four screws.
6. Remove the base.
7. Place the wall mounting arm (not included) onto the back of the
monitor. Line up the holes of the arm with the holes in the back of the
monitor.
8. Insert the 4 screws into the holes and tighten.
9. Reconnect the cables. Refer to the manual of wall mounting arm
for instructions on attaching it to the wall.
6 7
CONTROL BUTTONS
Front Controls
Button Description:
1. Auto Adjust / Exit
Before activating the OSD menu, this button can be used to automa-
tically adjust the display to the horizontal/ vertical position, Clock and
Focus. (Press button for 2 seconds)
When OSD menu is in active status, press this button to exit OSD menu.
2. Brightness
Adjust brightness
To scroll up the menu or increase the value of selected item.
3. Contrast
Adjust contrast
To scroll down the menu or decrease the value of selected item.
4. Menu / Enter
Press this button to turn on the OSD main menu or activate/
deactivate selected item.
Press this button to exit OSD menu when in Brightness/ Contrast
OSD status.
5.: Power Indicator
When light is green, the power is on, orange when the power is active off.
6. Power Button
Press this button to turn ON/ OFF the monitor’s power.
7. Headphone Jack
8. Volume control

MENU DESCRIPTIONS
Main Menu
CONTRAST
Selecting this control allows you to make adjustments to the contrast of
the display screen.
BRIGHTNESS
Selecting this control allows you to make adjustments to the luminosity
level of the display screen.
FOCUS (AVAILABLE IN ANALOG MODE ONLY)
Selecting this control allows you to make adjustments to the picture
focus (pixel clock signal).
CLOCK (AVAILABLE IN ANALOG MODE ONLY)
Selecting this control allows you to make adjustments to the picture
clock (pixel frequency).
HORIZONTAL POSITION (AVAILABLE IN ANALOG MODE ONLY)
Moving the screen image horizontally.
VERTICAL POSITION (AVAILABLE IN ANALOG MODE ONLY)
Moving the screen image vertically.
INPUT SELECT
Switching main input signal (select analog or digital input source).
ON-SCREEN DISPLAY
This LCD monitor features an On-Screen Display (OSD) menu. These
icons are designed to make your monitor display settings easier. When
highlighted, the icons illustrate the control function to assist you in
identifying which control needs adjustment.
Before activating the OSD menu, the “Auto Adjust” button (1) can be used
to automatically adjust the display to the horizontal and vertical position,
Clock and Focus. (Press button for 2 seconds.)
Note: When setting up this monitor for the first time, perform Auto Image
Adjust function.
For screen adjustments, press the “Menu” button (4) to display the OSD
(On-Screen Display) Main Menu. Press the (2) or (3) button to
scroll up or down the menu to your required options then press the “Menu”
button (4) to confirm your selection. Press the (2) button to increase
the value and press the (3) button to decrease the value. After your
adjustment, press the “Menu” button (4) to go back to previous menu.
Please note that the OSD will automatically turn off in 10 seconds without
any manipulation or by simply pressing the “Menu” button (4) to exit the
OSD Menu.
8 9

MENU DESCRIPTIONS
LANGUAGE
To choose language used in the menus and control screens.
SCALING MODE
To adjust the input signal to the screen size by using the following options:
- Fill All: To adjust the signal to the full screen.
- Fill Aspect Ratio: To adjust the horizontal signal to full screen but
maintain the original vertical signal.
This function only works when the resolution setting is lower than the
native resolution of 1280 x 1024.
C1 (6500°K)
Default color Temperature setting: Adjust the color temperature to 6500°K
x = 0.313, y = 0.329
C2 (7800°K)
Default color Temperature setting: Adjust the color temperature to 7800°K
x = 0.296, y = 0.311
RED
Individual adjustments for red. Adjusts the intensity of red.
GREEN
Individual adjustments for green. Adjusts the intensity of green.
BLUE
Individual adjustments for blue. Adjusts the intensity of blue.
RESET
To set all the adjustments to factory default values.
EXIT
To save user adjustments and exit OSD menu.
10 11
C1
C2
POWER MANAGEMENT
The power management feature of this monitor is comprised of two
stages: On or Out Of Range (Green), OFF (Amber).
Power Mode H-Sync V-Sync Video LED Color
Normal Pulse Pulse Active Green
Out Of Range Pulse Pulse Active Green
Off Pulse No pulse Blanked Amber.
Off No pulse Pulse Blanked Amber
Off No pulse No pulse Blanked Amber
This monitor meets the Green Monitor standards as set by the Video
Electronics Standards Association (VESA). This feature is designed to
conserve electrical energy by reducing power consumption when there is
no video input signal present. When there is no video input signal this
monitor, following a time-out period, will automatically switch to an OFF
mode. This reduces the monitor's internal power supply consumption.
After the video input signal is restored, full power is restored and the
display is automatically redrawn. The appearance is similar to a
"Screen Saver" feature except the display is completely off. The display
is restored by pressing a key on the keyboard, or clicking the mouse.
PLUG & PLAY
This monitor is equipped with VESA DDC1/2B capabilities according to
the VESA DDC STANDARD. It allows the monitor to inform the host
system of its identity and, depending on the level of DDC used,
communicate additional information about its display capabilities. The
communication channel is defined in two levels, DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host
that continuously transmits EDID information. The DDC2B is a
bidirectional data channel based on the I²C protocol. The host can request
EDID information over the DDC2B channel.
NOTE:
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPE-
RATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.

TIMING GUIDE
Timing Table
Resolution Frequency
Preset Horizontal Vertical Horizontal Vertical signal input
M1 640 480 31.5kHz 60Hz analog / digital
VGA M2 640 480 35.0kHz 67Hz analog / digital
M3 640 480 37.5kHz 75Hz analog / digital
M4 640 480 37.9kHz 73Hz analog / digital
M5 800 600 37.9kHz 60Hz analog / digital
M6 800 600 46.9kHz 75Hz analog / digital
SVGA M7 800 600 35.2kHz 56Hz analog / digital
M8 800 600 48.0kHz 72Hz analog / digital
M9 832 624 49.7kHz 75Hz analog / digital
M10 1024 768 48.4kHz 60Hz analog / digital
XGA M11 1024 768 56.5kHz 70Hz analog / digital
M12 1024 768 60.0kHz 75Hz analog / digital
M13 1280 1024 64.0kHz 60Hz analog / digital
SXGA M14 1280 1024 80.0kHz 75Hz analog / digital
M15 1280 1024 91.2kHz 85Hz analog
M16 1152 864 80.0kHz 75Hz analog / digital
M17 1280 960 60.0kHz 60Hz analog / digital
M18 1280 960 85.9kHz 85Hz analog
M19 640 400 31.5kHz 70Hz analog / digital
DOS M20 640 350 31.5kHz 70Hz analog / digital
M21 720 400 31.5kHz 70Hz analog / digital
TIMING GUIDE
The LCD is a multi-frequency display. On analog input it operates at
horizontal frequencies between 24KHz - 93KHz and vertical frequencies
between 55Hz - 85Hz; on digital input it operates at horizontal frequencies
between 24KHz - 83KHz and vertical frequencies between 55Hz - 85Hz
Because of its microprocessor-based design, it offers auto-
synchronization and auto-sizing capabilities. This monitor offers 21 pre-
programmed settings that are listed in the timing table on page 13.
These preset modes cover most of the common video modes supported
by popular graphics adapters. However, each adapter’s implementation of
these video modes may vary slightly. If you find it necessary to make
minor display adjustments (for example, horizontal and vertical position).
Please refer to the On Screen Display section of this manual for
instructions.
If you would like to use one of the preset timing modes, please refer to
your video card manufacturer’s installation guide for instructions on how
to make these changes. The video card controls the refresh rate. Most
video cards provide a software utility or hardware DIP switches that allows
you to change the frequency used for each resolution.
12 13

14
PIN ASSIGNMENT
Connector (15-pin) Connector (24-pin)
Pin 1Red Pin 1TMDS Data 2-
Pin 2Green Pin 2TMDS Data 2+
Pin 3Blue Pin 3TMDS Data 2/4 Shield
Pin 4Ground Pin 4TMDS Data 4-
Pin 5Ground Pin 5TMDS Data 4+
Pin 6Red Ground Pin 6DDC Clock
Pin 7Green Ground Pin 7DDC Data
Pin 8Blue Ground Pin 8No Connection
Pin 9+5V Pin 9TMDS Data 1-
Pin 10 Detect Cable Pin 10 TMDS Data 1+
Pin 11 No Connection Pin 11 TMDS Data 1/3 Shield
Pin 12 DDC SDA Pin 12 TMDS Data 3-
Pin 13 Horizontal Sync. Pin 13 TMDS Data 3+
Pin 14 Vertical Sync. Pin 14 +5V
Pin 15 DDC SCL Pin 15 Ground
Pin 16 Hot Plug Detect
Pin 17 TMDS Data 0-
Pin 18 TMDS Data 0+
Pin 19 TMDS Data 0/5 Shield
Pin 20 TMDS Data 5-
Pin 21 TMDS Data 5+
Pin 22 TMDS Clock Shield
Pin 23 TMDS Clock +
Pin 24 TMDS Clock -
Note: When resolutions are shown that are lower than the pixel count of the LCD
panel, text may appear choppy or bold. This is normal all current flat panel
technologies when displaying non-native resolutions on a full screen (below than
1280 x 1024 resolution). In flat panel technologies, each dot on the screen is
actually one pixel, so to expand resolutions to full screen, an interpolation of the
resolution must be down. When the interpolated resolution is not an exact
multiple of the native resolution, the mathematical interpolation necessary may
cause some lines to appear thicker than others.
SPECIFICATIONS
LCD Type 19” (48.2cm)
Active Matrix Panel, 0.294mm pixel pitch
Color Filter R, G, B Analog Interface
Digital Interface
Colors up to 16.7M
Glass surface Anti-glare coating
Viewing
Angles Left / Right 170°
(CR>5) Up / Down 170°
Contrast Ratio Typ. 700 : 1
Luminance of White Typ. 250cd/m²
Response Time Typ. 25 ms
Compatibility PC IBM XT, AT, 386, 486, Pentium or PS/2
and compatibles (from VGA up to
1280 x 1024 @ 85 Hz)
Refresh Rate Max. Analog 1280 x 1024 @ 85Hz (60Hz rec.)
Max. Digital 1280 x 1024 @ 75Hz (60Hz rec.)
Audio Rated Power 2W rms (Per channel)
Connectors Input Signal 15-pin D-SUB
Input Signal 24-pin DVI
USB Hub 1up, 4down
Power Jack type DC + 12V In
Power Input AC 100-240V 50-60Hz
Output DC 12V
Consumption 65 watts (Maximum)
Display Area Max. 376.32mm (H) x 301.056mm (V)
Operating Temperature 0°C to 40°C
Humidity 20% RH to 85% RH (no condensation)
Storage Temperature -10°C to 50°C
Conditions Humidity 20%RH to 85%RH (no condensation)
Dimension 432mm (W) x 440mm (H) x 198mm (D)
Weight Net 5.9kg

TROUBLESHOOTING
Double (split) screen image.
üMake sure your graphics card is set to Non-Interlaced mode.
Entire screen image rolls (scrolls) vertically.
üMake sure the input signals are within the LCD monitor’s specified
frequency range.
(Maximum Analog Input: VESA, MAC 1280 x 1024 @85Hz)
üConnect the video cable securely.
üTry the miro Monitor with another power source.
Control buttons do not work.
üPress only one button at a time.
TROUBLESHOOTING
No power.
üFlip the power switch ON. The Power LED turns on.
üMake sure AC power cord is securely connected to the power jack
and to a power outlet.
Power on but no screent image.
üMake sure the video cable attached with this monitor is tightly
secured to the video output port on the back of the computer.
üAdjust the brightness and contrast.
Image is unstable, unfocused.
üUse “AUTO ADJUST” to adjust automatically.
üCheck whether the resolution or refresh rate in windows display
setting is beyond supported range(please refer to the specification
of supported mode).
Flickering.
üNot enough power is being supplied to the miro TD490 Monitor.
Connect the miro TD490 Monitor to a different outlet. If a surge
protector is being used, there may be too many devices plugged in.
üSee Timing Guide in this manual with a list of refresh rates and
frequency settings showing the recommended setting for the
miro TD490 Monitor.
Wrong or abnormal colors.
üIf any colors (Red, Green, or Blue) are missing, check the video
cable to make sure it is securely connected. Loose pins in the
cable connector could cause a bad connection.
üConnect the miro TD490 Monitor to another computer.
üCheck the graphics card for proper sync scheme (or sync
polarities) to match the miro TD490 Monitor’s specifications.
16 17

For European Countries
In Europe you must use a cord set which is appropriate for the recepta-
cles in your country. The cord set is HAR-Certified, and a special mark
that will appear on the outer sheath, or on the insulation of one of the inner
conductors.
AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM
FOR YOUR SAFETY PLEASE READ THE FOLLOWINT TEXT CAREFULLY.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET
THEN THE PLUG SHOULD BE CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF
PLUG IS INSERTED INTO AN APPROPRIATE SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance
with the following code:
Green-and-Yellow : Earth
Blue : Neutral
Brown : Live
If the coloured wires of the mains lead of this appliance do not correspond
with the coloured markings identifying the terminals in your plug, proceed
as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to
the terminal in the plug which is marked by the letter E or by the Earth
symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the
plug which is marked with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal in the plug which
is marked with the letter L or coloured RED.
If you have any questions concerning which proper power cord to use,
please consult with the dealer from whom you have purchased the product.
APPENDIX
Safety Guidelines
Warning: This device must be operated with the original power supply
CAUTION: The socket-outlet should be isntalles near the equipment
and should be easily accessible.
CAUTION: Use a power cable that is properly ground. Always use the
appopriate AC cord that is certified for the individual
country. Some examples are listed below.
USA...................UL Switzerland ......SEV
Canada..............CSA Britain...............BASE/BS
Germany ...........VDE Japan ...............Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and been selected
according to the country of destination and must be used to pervent
electric shock. Use the following guidelines if it is necessary to replace
the original caord set, or if the cord set is not enclosed.
The female receptacle of the cord set must meet IEC-60320 require-
ments and may look like (Figure A1 below):
FOR THE UNITED STATES AND CANADA
In the United States and Canada the male plug is a NEMA5-15 style (Figure
A2), UL Listed, and CSA Labeled. For units which are mounted on a desk
or table, type SVT or SJT cord sets may be used. For units which sit on the
floor, only SJT type cord sets may be used. The cord set must be selected
according to the current rating for your unit. Please consult the table below
for the selection criteria for power cords used in the United States and
Canada.
Code Type Size of Conductors in Cord Maximum Current Rating of Unit
SJT 18 AWG 10 Amps
16 AWG 12 Amps
14 AWG 12 Amps
SVT 18 AWG 10 Amps
17 AWG 12 Amps

Compliance Information for U.S.A.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interferen-
ce in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordan-
ce with the instructions, may cause harmful interference to radio commu-
nications.
However, there is no guarantee that interference will not occur in a parti-
cular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interfe-
rence by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or
moisture. Dangerously high voltages are present inside the monitor. Do
not open the cabinet. Refer servicing to qualified personnel only.
CE Conformity for Europe
The device complies with the requirements of the
ECC directive 89/336/EEC as amended by 92/31/EEC
and 93/68/EEC Art.5 with regard to “Electromagnetic
compatibility”, and 73/23/EEC as amended
by 93/68/EEC Art.13 with regard to “Safety”.

INHALTSVERZEICHNIS
EINFÜHRUNG
Sicherheitsrichtlinien..........................................................................i
Vorsichtsmaßregeln für den Gebrauch des Monitors........................i
Pflege des Monitors ........................................................................iii
Aufstellplatz des Monitors................................................................iv
Allgemeine Informationen ................................................................1
Prüfliste Zubehör..............................................................................2
Gerätemerkmale ..............................................................................3
INSTALLATION
Installation des Monitors ..................................................................5
Installation VESA Wandbefestigung ................................................7
Bedienung ........................................................................................8
OSD-Bildschirm-Menü......................................................................9
OSD-BILDSCHIRM
Menü Erläuterungen ......................................................................10
SONSTIGES
Stromsparsystem............................................................................12
Plug & Play ....................................................................................12
Einstellungsrichtlinien (Timing Guide)............................................13
Timing Table ..................................................................................14
Pinbelegung....................................................................................15
Spezifikationen ..............................................................................16
Im Störungsfalle..............................................................................17

SICHERHEITSRICHTLINIEN
VORSICHTSMAßREGELN FÜR DEN GEBRAUCH DES MONITORS
Bei Ihrem Monitor handelt es sich um ein hochwertiges elektronisches
Gerät. Zu Ihrer eigenen Sicherheit und um die Funktionalität des Monitors
zu gewährleisten, empfehlen wir folgende Warnhinweise sorgfältig zu
beachten.
Behandeln Sie den Montior vorsichtig.
•Reiben Sie nicht mit einem harten Gegenstand am Monitor und
setzen Sie ihn keinen Schlägen aus, da er sonst beschädigt und die
Anzeige zerkratzt werden kann.
•Üben Sie keinen Druck auf den Flüssigkristall-Bildschirm durch
Berühren oder verkratzen mit harten Gegenständen aus.
•Stellen Sie keine Gegenstände auf dem Monitor ab und achten Sie
darauf, dass nichts in die Belüftungsschlitze des Monitors fallen
kann. Gegenstände, die durch diese Schlitze in das Innere des
Monitors gelangen, können zu Beschädigungen führen. Zudem setzen
Sie sich dabei der Gefahr eines elektrischen Stromschlages aus.
•Falls der Monitor beschädigt ist, vermeiden Sie unbedingt den
Kontakt der Flüssigkristalle mit Haut, Augen oder Mund. Die
Flüssigkristalle des Monitors enthalten Reizstoffe, die schädlich sind.
Falls doch Kontakt entsteht, waschen Sie die entsprechende Stelle
unter fließendem Wasser gut ab und konsultieren Sie einen Arzt.
•Beim Tragen des Monitors mit einer Hand den Standfuß des
Monitors unterstützen mit der anderen dessen Display halten.
Behandeln Sie das Gehäuse vorsichtig.
•Unterlassen Sie das Öffnen des Gehäuses. Überlassen Sie
Wartungs- bzw. Reparaturarbeiten ausschließlich qualifiziertem
Fachpersonal.
•Beim Transport des Monitors darauf achten, dass er keinen großen
Erschütterungen ausgesetzt wird.
•Wenn flüchtiges Lösungsmittel oder Klebstoff mit dem Gehäuse in
Berührung kommt, kann die Oberfläche beschädigt oder die Farbe
abgelöst werden.
i

SICHERHEITSRICHTLINIEN
PFLEGE DES MONITORS
•Reinigen Sie das Gehäuse des Monitors gelegentlich mit einem
weichen, leicht mit Wasser angefeuchteten Tuch.
•Verwenden Sie zur Reinigung der Bildfläche des Monitors auf keinen
Fall Seife, Fensterputzmittel oder ähnliche Reinigungsmittel.
Wischen Sie die Bildfläche ab und zu mit einem weichem, leicht mit
Wasser angefeuchteten Tuch ab.
•Verwendung eines chemisch behandelten Lappens oder eines
glanzerzeugenden Reinigungsmittels kann die Oberfläche
beschädigen oder ein Ablösen der Farbe verursachen.
•Achten Sie darauf, dass kein Wasser oder Öl in die Sichtanzeige
eindringen kann, da Tröpfchen im Laufe der Zeit Verfärbungen und
Entfärbungen verursachen können.
•Halten Sie Nahrungsmittelpartikel vom Anzeigefeld fern und
hinterlassen Sie keine Fingerabdrücke darauf.
SICHERHEITSRICHTLINIEN
Gehen Sie sorgsam mit dem Netzkabel um.
•Speziell beim unachtsamen Gebrauch des Netzkabels besteht die
Gefahr eines elektrischen Stromschlages.
•Stellen Sie keine schweren Gegenstände auf das Netzkabel,
schließen Sie keine Zweigleitungen an, verknoten Sie es nicht, und
ziehen Sie nicht am Kabel, um den Stecker aus der Steckdose zu
ziehen. Wenn das Netzkabel beschädigt ist, besteht Brand- und
Stromschlaggefahr.
•Fassen Sie den Netzstecker niemals mit nassen Händen an, da
anderenfalls Stromschlaggefahr besteht.
•Wenn Sie den Monitor bewegen, trennen Sie diesen immer von der
Stromzufuhr.
•In einer Notsituation sofort das Netzkabel von der Steckdose trennen.
•Bevor Sie das Signalkabel des Monitors mit dem Computer
verbinden, den Netzstecker immer vom Strom trennen.
•Trennen Sie das Gerät während eines Gewitters vom Netz, aber
auch dann, wenn Sie es für längere Zeit nicht verwenden. Dies
schützt den Monitor vor Beschädigungen durch Spannungsspitzen.
ii iii

ALLGEMEINE INFORMATIONEN
Wir gratulieren zum Kauf dieses hochauflösenden LCD-Monitors.
Ihr LCD-Monitor ist mit der neuesten Farb-Flüssigkeitskristallanzeige
(LCD-) Technologie ausgestattet. Sie bietet Ihnen bei einer Auflösung von
1280 x 1024 Bildpunkte einen hohen Kontrast und das bei einem
Betrachtungswinkel von bis zu 170°. Der Monitor lässt sich auf die
meisten Video-Betriebsarten sowohl bei IBM-kompatiblen PCs als auch
bei Apple Macintosh-Computern synchronisieren und an diese anpassen.
Der ergonomisch angepasste Flachbildschirm bietet ein erweitertes
Bildschirm-Menü (OSD) mit animierten Befehls-Icons, die eine einfache
und problemlose Einstellung des Monitors ermöglichen.
Das vorliegende Handbuch beschreibt die Funktionen und
Leistungsmerkmale des Monitors ausführlich, damit Sie ihn so effizient
wie möglich einsetzen können.
SICHERHEITSRICHTLINIEN
AUFSTELLPLATZ DES MONITORS
•Vermeiden Sie direktes Sonnenlicht und ultraviolette (UV-) Strahlung,
die eine nachteilige Auswirkung auf Gehäuse und Teile haben.
Vermeiden Sie extreme Hitze oder Kälte.
•Setzen Sie den Monitor niemals einer Temperatur höher als 60°C
und einer Luftfeuchtigkeit über 85% aus.
•Vermeiden Sie in jedem Fall Kondensation, wird das Gerät aus einer
kalten Umgebung in ein wärmeres eventuell feuchtes Umfeld
gebracht, kondensiert Feuchtigkeit im Inneren Ihres Monitors. Wird
anschließend der Monitor eingeschaltet, können zu diesem
Zeitpunkt interne Komponenten des Monitors beschädigt werden.
Aus diesem Grund warten Sie bitte mit dem Einschalten des
Monitors, bis sich die Innentemperatur des Gerätes an die
Umgebungstemperatur angepasst hat und eventuell entstandene
Feuchtigkeit in dieser Zeit trocknen kann.
•Ist der Monitor in Betrieb, legen Sie ihn nicht horizontal hin.
•Stellen Sie Ihren Monitor auf eine stabile und sichere Unterlage.
Sollte der Monitor fallen, können ernsthafte Schäden an dem Gerät
entstehen. Außerdem besteht in diesem Fall Verletzungsgefahr.
Verwenden Sie nur einen vom Hersteller empfohlenen oder mit dem
Monitor gelieferten Standfuß.
•Die Schlitze und Öffnungen im Monitorgehäuse dienen der
Belüftung. Um einen störungsfreien Betrieb des Monitors zu
gewährleisten und ihn vor Überhitzung zu schützen, dürfen Sie diese
Öffnungen keinesfalls abdecken. Stellen Sie den Monitor so auf,
dass eine ausreichende Luftzirkulation gewährleistet ist.
Schäden, die auf Missachtung obiger Warnhinweise zurückzuführen sind
sowie mechanische Defekte wie z.B. Bruch des Gehäuses, Kratzer auf dem
LCD-Bildschirm etc., werden nicht durch Garantieleistungen abgegolten.
iv 1

GERÄTEMERKMALE
QUALITATIV HOCHWERTIGE FLÜSSIGKRISTALL-ANZEIGEEINHEIT
•Die 19-Zoll-Anzeigeeinheit (0.294mm Pixelabstand) und die Blend-
schutz-Hartbeschichtung gewährleisten geringe Reflexionen,
Antistatik, hohe Auflösung und starken Kontrast mit Echtfarb-Anzeige
(bis zu 16.7 Mio. Farben).
PLUG & PLAY
•Dieses Gerät entspricht der VESA®-Norm (Video Electronics Standards
Association) DDCTM 1/2B (Display Data Channel) gemäß den
Windows®Spezifikationen.
DIGITAL-MULTI-SCAN
•Bei einem analogen Signaleingang arbeitet dieses Gerät mit einer
Horizontalfrequenz von 24 ~ 93 kHz, einer Vertikalfrequenz von 55 ~ 85Hz
und einer maximalen Auflösung von 1280 (H) x 1024 (B) bei 85Hz.
•Bei einem digitalen Signaleingang arbeitet dieses Gerät mit einer
Horizontalfrequenz von 24 ~ 83 kHz, einer Vertikalfrequenz von 55 ~ 85 Hz
und einer maximalen Auflösung von 1280 (H) x 1024 (B) bei 75Hz.
•Der Monitor ist sowohl mit IBM®PC-kompatiblen Geräten als auch
Macintosh®-Geräten kompatibel.
FORMATEINSTELLFUNKTION
•Das Gerät verfügt über eine On-Screen-Display-Kontrolle. Diese
ermöglicht über diverse Einstellungspunkte eine problemlose und
einfache Installation des Monitors. Folgende Einstellmöglichkeiten sind
gegeben: Automatische Anpassung, Helligkeit, Kontrast,
Wahl der Eingangsquelle, Fokus, Clock, H-Position, V-Position,
Sprache, Scaling, Farbtemperaturauswahl (6500°K, 7800°K),
RGB Farbtemperaturauswahl, Zurücksetzen, Exit
STROMZUFUHR
•Der Netzadapter besteht aus zwei Teilen: einem kompakten
Adapterblock mit einem Monitor-Anschlusskabel sowie dem
länderspezifischen Netzkabel.
•Der Netzadapter wandelt die jeweilige Netzspannung (100-240V) in die
für den Monitor nötige Gleichspannung.
•Stromverbrauch des Gerätes: - On mode: max. 65 Watt
- Stand-by mode: max. 3 Watt
- Off mode: max. 2 Watt
PRÜFLISTE ZUBEHÖR
Bevor Sie Ihren Monitor in Betrieb nehmen, überprüfen Sie bitte den Inhalt
der Verpackung auf Vollständigkeit. Folgende Komponenten sollten im
Lieferumfang enthalten sein:
• TFT Farbflachbildschirm
• mitgeliefertes Zubehör:
1. Netzadapter und Netzkabel
2. 15-pin D-SUB Signalkabel
3. DVI-D-Digitalsignalkabel
4. USB Kabel
5. Audio Kabel
6. Benutzerhandbuch
2 3