miseno MMC3026LED User manual

MEDICINE CABINET – DOUBLE
DOOR WITH LED LIGHTED MIRROR
Model: MMC3026LED, MMC4026LED, MMC4826LED
USER GUIDE

IMPORTANT SAFETY INFORMATION
WARNING
This product must be installed in accordance with the installa on instruc on by
qualiĮĞĚ technician. Failure to follow instruc on could result in death or serious
bodily injury.
Please read through this installa on instruc on so you will know how to install
and operate your model properly. Keep this document in a safe place for future
reference a er use.
CAUTION
This product must be serviced by qualiĮĞĚ personnel. ALWAYS unplug the power
cord or turn oīƚŚe circuit breaker before service.
PACKAGE CONTENTS
(x1)
Cabinet
Moun ng Bracket Screw Drywall Anchor
2Customer Service: [phone] or [email protected]
(Model MMC3026LED x1)
(Model MMC4026LED x1)
(Model MMC4826LED x1)
(Model MMC3026LED x4)
(Model MMC4026LED x7)
(Model MMC4826LED x7)
(Model MMC3026LED x4)
(Model MMC4026LED x7)
(Model MMC4826LED x7)

INSTALLATION
For drywall installaƟŽŶ,
mark the hole locaƟŽŶƐ and
drill Ɍ6mm holes for the
drywall anchors.
Insert provided drywall
anchors.
Install the mounƟng bracket.
Connect to 110V power
supply.
Hang the mirror to the wall and
make sure the bracket in the
back of the mirror lineup with
the mounƟng bracket properly.
Press the mirror down
slightly and make sure the
brackets Įt properly.
3
•Using the wall studs to hang the mirror is highly recommended.
•This mirror is NOT designed to work with dimmable wall switch.
•IR sensor requires a minimum clearance of 5 1/4”.
Customer Service: [phone] or [email protected]

INSTALLATION DIMENSIONS
Model # A B C
30 26 4 3/4
40 26 4 3/4
48 26 4 3/4
4
B
A
C
Customer Service: [phone] or [email protected]
MMC3026LED
MMC4026LED
MMC4826LED

BASIC OPERATION
1. Rocker switch
a. Turn switch to <–> posiƟon; lights can be controlled by the IR sensor.
b. Turn switch to <o> posiƟon to turn oīthe lights.
c. Turn switch to <=> posiƟon to turn on the lights.
2. Dimmable IR sensor
a. Turn the Rocker switch to <–> posiƟon to acƟvate the IR sensor.
b. Move your hand across the IR sensor to turn the lights on or oī.
c. The distance between your hand and the sensor should be approx. 1”.
d. To adjust the brightness of the lights, keep your hand in front of the
sensor unƟl the desirable brightness has reached and move your hand
away from the sensor.
e. If the lights Ňicker, the level of brightness might be too low; try to
adjust the brightness to a higher level.
5
Customer Service: [phone] or [email protected]

CARE AND MAINTENANCE
6
Clean the mirror with a soŌ, damp cloth and dry thoroughly with a soŌtowel. Do NOT allow
the edges of the mirror to get or remain wet over a period of Ɵme. Please do NOT use glass
cleaner that contains ammonia or vinegar. Never spray any cleaner directly onto a mirror.
Instead apply the cleaner to a soŌcloth and then wipe the mirror. Make sure no
commercial cleaner comes in contact with the edge or backing.
DEFECTIVE GOODS CONSUMER WARRANTY
MISENO inspects all of its products prior to shipment. We oīer a 5-year Limited warranty
on our electric mirror products. DefecƟve products should be returned to place of purchase
for replacement. However, if this is not possible, we accept returns on defecƟve product
with our wriƩen authorizaƟon. Returns will be handled by product replacement. Defects
or damage caused to product by the consumer are not accepted.
SHORTAGE OR DAMAGED PRODUCTS
All shipments are carefully inspected and counted before leaving our distribuƟon centers.
Please inspect carefully on receipt of merchandise, noƟng any discrepancy or damage on
the carrier’s freight bill at that Ɵme, and Įle a claim with the carrier within 10 days from
receipt of order. Then contact our oĸce. DeducƟons from invoices for shortages or
damage claims will not be allowed.
RETURN NEW GOODS
All claims for returns or adjustments must have prior approval
and return authorizaƟon (RGA) number. Only original, sealed
product in salable condiƟon are eligible for return. Credit for authorized returns will be
issued at the net price paid for the product and subject to a 15% restocking/handling fee.
Merchandise is to be returned via prepaid freight. All unauthorized returns will be refused
or subject to a 25% restocking/handling fee.
WARRANTY
Customer Service: [phone] or [email protected]

REPLACEMENT PARTS
7
Part DescripƟon
1MirrorDoor
2Hinge
3Aluminum
Cover
4Aluminum
Panel
5ConnĞĐƟŽn
Box
6LEDDriver
7LED Light
Strip
8RockerSwitch
9Dimmable IR
Sensor
10 Mirror
11 Back Board
12 Glass Shelf
Customer Service: [phone] or [email protected]

© MISENO All rights reserved.
ϰϬϭKƩĞƌƐŽŶƌŝǀĞ
ŚŝĐŽϵϱϵϮϴ
wwwŵŝƐĞŶŽĐŽŵ
V6.1