U-Line DELUXE ALL MESH CHAIR H-9764 User manual

PAGE 1 OF 9 0522 IH-9764
H-9764, H-9765
DELUXE ALL MESH CHAIR
1-800-295-5510
uline.com
1. Insert casters into legs of five-star base. Turn base
upright. Insert gas lift into center of base.
(See Figure 1)
Figure 1
Gas Lift
Screw x 2
M6 x 16 mm
(for H-9765 only)
Screw x 8
M8 x 20 mm
Screw x 6
M6 x 30 mm
Hardware Kit
Back Support x 1
Armrest x 2
5-Star Base x 1
Mechanism x 1
Headrest x 1
(for H-9765 only)
Headrest Cap x 1
(for H-9765 only)
Caster x 5
Seat Cushion x 1
Gas Lift x 1
PARTS
ASSEMBLY
TOOL NEEDED
Allen Wrench
(included)
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.

PAGE 2 OF 9 0522 IH-9764
ASSEMBLY CONTINUED
2. Align armrest with holes on bottom of seat cushion.
Use three M6 x 30 mm screws to attach. Repeat on
opposite side. (See Figure 2)
NOTE: Use Allen wrench to tighten all screws.
Figure 2 M6 x 30 mm
Screw
3. Align mechanism with holes on bottom of seat
cushion. Use four M8 x 20 mm screws to attach.
(See Figure 3)
Figure 3 M8 x 20 mm
Screw
4. Position back support in slot between bottom of
seat cushion and mechanism. Align holes and use
four M8 x 20 mm screws to attach back support to
mechanism. (See Figure 4)
Figure 4 M8 x 20 mm
Screw
5. Slowly lower chair assembly onto the gas lift. Press
down on seat cushion to secure in place.
(See Figure 5)
Figure 5

PAGE 3 OF 9 0522 IH-9764
CHAIR ADJUSTMENTS
1. Seat Height Adjustment – To raise seat height, lift
back side of lever up with little to no weight on the
seat. To lower seat height, lift lever up while sitting.
2. Adjustable Tilt Lock – To lock seat/back angle, press
lever down at desired angle. Chair has synchro tilt;
the back tilts at a two-to-one ratio to the seat angle.
3. Seat Depth (Seat Slider) – To adjust seat depth, lift the
front side of lever and slide the seat forward or back
while sitting.
4. Armrest Height Adjustment – To adjust armrest height,
press the button on side of each armrest and move
the armrest up or down.
Self-Weight Tilt Tension – Tilt tension automatically adjusts
based on user's weight.
1
-800-295-551
0
uline.com
ASSEMBLY CONTINUED
1
3
2
4
6. If not attaching headrest, insert headrest cap into
opening on top of back support. (See Figure 6)
Figure 6
TO ATTACH HEADREST (H-9765):
1. With headrest cap removed, align holes of headrest
with holes on top of back support. Attach using two
M6 x 16 mm screws. (See Figure 7)
Figure 7

PAGE 4 OF 9 0522 IH-9764
SILLA TODA DE MALLA
DE ALTA CALIDAD
800-295-5510
uline.mx
H-9764, H-9765
1. Inserte las ruedas en las patas de la base estrella.
Enderece la base. Inserte el pistón de gas en el
centro de la base. (Vea Diagrama 1)
Diagrama 1
Pistón de Gas
2 Tornillos
M6 x 16 mm
(solo para H-9765)
8 Tornillos
M8 x 20 mm
6 Tornillos
M6 x 30 mm
Kit de Tornillería
1 Respaldo
2 Descansabrazos
1 Base Estrella
1 Mecanismo
1 Cabecera
(solo para H-9765)
1 Tapa para Cabecera
(solo para H-9765)
5 Ruedas
1 Asiento
1 Pistón de Gas
PARTES
ENSAMBLE
HERRAMIENTA NECESARIA
Llave Allen
(incluida)

PAGE 5 OF 9 0522 IH-9764
CONTINUACIÓN DEL ENSAMBLE
2. Alinee el descansabrazos con los orificios en
la parte inferior del asiento. Utilice tres tornillos
M6 x 30 para fijarlo. Repita la operación con el
lado opuesto. (Vea Diagrama 2)
NOTA: Utilice la llave Allen para apretar todos
los tornillos.
Diagrama 2
Tornillo M6 x 30 mm
3. Alinee el mecanismo con los orificios en la parte
inferior del asiento. Use cuatro tornillos M8 x 20 mm
para fijarlo. (Vea Diagrama 3)
Diagrama 3
Tornillo M8 x 20 mm
4. Posicione el respaldo en la ranura que está entre la
parte inferior del asiento y el mecanismo. Alinee los
orificios y utilice cuatro tornillos M8 x 20 mm para
fijar el respaldo al mecanismo. (Vea Diagrama 4)
Diagrama 4
Tornillo M8 x 20 mm
5. Baje lentamente el ensamble de la silla sobre el
pistón de gas. Presione el asiento para asegurarlo
en su lugar. (Vea Diagrama 5)
Diagrama 5