Missouri Wind and Solar POLE 300W User manual

Blow Hard + Shine Bright 332 Cobble Stone Drive, Seymour, MO 65746
www.mwands.com • (417) 708–5359
Triple Solar Panel Top of Pole Mounng Rack Assembly
See more about this product on YouTube at: hps://youtu.be/tZ7blvUkGTY and hps://youtu.be/KgKnyGXBqUI
Model: POLE_300W
Date: 07/2018
Page: 1 of 2
Pipe Grip Tie to
Mount Plate Assembly
For this step, you will need the
mount plate assemblies and
the pipe grip es. Connect one
2-⅜" pipe grip e to each mount
plate assembly using two sets
of ⅜" bolts and lock nuts each.
The bolt head should be on the
exterior of the mount plate.
Hand ghten only.
Solar Mount End Bracket
to Mount Plate Assembly
Connect two of the solar mount
end brackets to each of the
mount plates using the ⅜" bolts
and lock nuts, as illustrated
above.
Support Arm to Brace Band Assembly
Connect one 24" and one 30" support
arm to each of the 2-⅜" brace bands
using one set of ⅜" bolts and lock nuts
each. Both arms will be assembled
inside the brace band as shown above.
Slide the assembled brace band and
support arms onto the pole. Mount the
assembled mount plate on the top of the
pole and ghten using a screwdriver.
Parts List:
(4) solar mount end bracket
(2) 16" mount plate
(2) ½" x 24" EMT support arm
(2) ½" x 30" EMT support arm
(2) 2-⅜" brace band
(2) bolt for brace
(2) 2-⅜" pipe grip e
(4) UniRac SolarMount “B” end clamp
(4) UniRac SolarMount “EF” mid clamp
(2) UniRac SolarMount Splice bar
(4) 43" secons SolarMount rail
(24) ⅜" bolt and ⅜" nyloc nut*
*YouTube video shows locking washers. These
are no longer included in the kit as they have
been replaced with nyloc nuts.
Bolt at
exterior
Mount
plate
UniRac
SolarMount
Splice Bar
Mount
plate
Support arms
Solar mount
end bracket
UniRac
SolarMount
Rail
Solar mount
end bracket
Pipe
grip
e
30"
Support
Arm
24"
Support
Arm
Bolt head
at exterior
Mount
plate
UniRac
SolarMount
“B” end clamp
Pipe
grip
e
Brace
band
UniRac
SolarMount
“EF” mid clamp

Blow Hard + Shine Bright 332 Cobble Stone Drive, Seymour, MO 65746
www.mwands.com • (417) 708–5359
Triple Solar Panel Top of Pole Mounng Rack Assembly
See more about this product on YouTube at: hps://youtu.be/tZ7blvUkGTY and hps://youtu.be/KgKnyGXBqUI
Model: POLE_300W
Date: 07/2018
Page: 2 of 2
Pole and Rail Installaon
Posion two 2" poles so that your panels will face directly south and install the poles in the ground approximately
5 . apart. Bury them unl about 2 . deep making sure they are level. Install a splice bar to join two rails
together (Fig. 1). The screws are self-drilling and will create their own hole as you screw them in. Repeat for
the other two rails. Insert six ⅜" bolts into the lower solar rail channel. Slide two of them close to the splice bar
temporarily to be used for the support arms. Posion the four outer ones to t the solar mount end bracket
holes. Posion the rail against the solar mount end brackets sliding rail and bolts into holes. Place the ⅜" nuts on
to the bolts and ghten down (Fig. 2). Repeat for both solar rail sets. Using the ⅜" bolts and nuts, aach the four
support arms (Fig. 2 and 3). Adjusng the lower support arms brace band hight on the poles will lt the whole
rail assembly at for ease of installing the solar panels. Make sure to ghten down all bolts aer you install solar
panels and make your lt angle adjustment.
Final Adjustments
Your solar panels will get the best producon when facing south, adjust your solar panels accordingly. You can
adjust the lt for beer performance in summer/winter (angle shown in Fig. 2 is typically good year round).Make
sure to ghten down all bolts.
Solar mount
end bracket
channel for
3/8" bolt
Solar panel
end clamp
channel
End Clamp and Mid Clamp Assembly
Assemble each bolt through the UniRac
SolarMount end clamps and mid clamps.
Slide, in this order, an end clamp, mid
clamp, second mid clamp, and second
end clamp into the channel of each
rail. Install the solar panels onto the rail
by ghtening the end clamps and mid
clamps over the edge of each solar
panel. Saw ends of bolt o
ush with lock nut to reduce
sideways shading on solar panel.
30" Support
Arm towards
center of rack,
mounted to
railing
Splice bar connecng rails(Fig. 1)
(Fig. 2)
(Fig. 3)
24"
Support
Arm
towards
outside
of rack,
mounted
to solar
mount end
bracket
of mount
assembly