Mitchell & Johnson SAP201V User manual

SAP201V
Integrated Stereo Amplifier with DAC
User Guide

Dear Valued Customer
Thank you for deciding to purchase this Mitchell & Johnson product. This instruction manual will give you a general idea of
how this device operates, as well as providing you with information on safety procedures and cleaning. In order to maintain
this product in good condition, and to ensure it’s safe operation, please take a few minutes to read and carefully follow all
the safety and operating instructions found in this manual.
Please retain this instruction manual for future reference and pass it along with the device if handed over to a third party.
Should you have any additional questions regarding the operation or installation of this device, or should any problems arise
from its use, then please contact a specialized dealer or our service team for further information.
We assume no liability for any damage incurred as a result of improper use resulting from failure to comply with the safety
instructions found in this manual. Under such circumstances all claims under warranty will become null & void. We assume no
liability for any consequential damage!
This product is EMV-certified and complies with all European and National guideline requirements. A declaration of CE
conformity has been established for this product. Certification has been documented and entrusted to the manufacturer

Table of Contents
1. INTENDED USE..................................................................................................................................................... 5
EXPLANATION OF SYMBOLS ..................................................................................................................................................... 5
2. SAFETY INFORMATION ........................................................................................................................................ 6
3. ACCESSORIES ....................................................................................................................................................... 7
4. DESCRIPTION OF PARTS ....................................................................................................................................... 8
FRONT PANEL....................................................................................................................................................................... 8
REAR PANEL......................................................................................................................................................................... 8
MITCHELL &JOHNSON RM200 REMOTE CONTROL HANDSET....................................................................................................... 9
5. SET UP AND CONNECTION TO OTHER DEVICES ...................................................................................................11
CORRECT CONNECTION OF ANALOG RCA AUDIO CABLES............................................................................................................ 11
CORRECT CONNECTION OF DIGITAL CABLES.............................................................................................................................. 11
CORRECT CONNECTION OF SPEAKERS ...................................................................................................................................... 12
CONNECTING ANALOG AUDIO COMPONENTS ........................................................................................................................... 13
CONNECTING A TURNTABLE .................................................................................................................................................. 13
CONNECTING A CD OR SACD PLAYER ..................................................................................................................................... 13
CONNECTING A NETWORK PLAYER/INTERNET RADIO/DAB+ TUNE ............................................................................................... 14
CONNECTING DIGITAL AUDIO COMPONENTS ............................................................................................................................ 14
CONNECTING A DEVICE VIA DIGITAL OPTICAL &DIGITAL COAXIAL CONNECTION.............................................................................. 14
CONNECTING THE POWER CABLE ........................................................................................................................................... 15
6. LISTENING TO AUDIO..........................................................................................................................................16
ADJUSTING THE TONE AND LEFT/RIGHT VOLUME BALANCE......................................................................................................... 18
7. TROUBLESHOOTING AND ERROR MESSAGES......................................................................................................19
8. MAINTENANCE AND HANDLING .........................................................................................................................20
TRANSPORTING OR SENDING THE DEVICE ................................................................................................................................. 20
KEEPING THE EXTERNAL CASE CLEAN ....................................................................................................................................... 20
CLEANING THE DEVICE.......................................................................................................................................................... 20
9. SPECIFICATIONS..................................................................................................................................................22
Before use
Please read this instruction manual thoroughly before operating this device and retain it for further reference. Following and
heeding all the information found in this instruction manual will maintain this product in good condition and ensure its safe
operation. This instruction manual contains information on how to operate and maintain this device. Should a component
require maintenance, servicing or repair, then please consult a qualified dealer or service technician.

Page 5 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
1. Intended Use
This device is an integrated stereo amplifier designed to have various hi-fi components connected to its inputs and a pair
of stereo speakers connected to the speaker terminals.
Please adhere to all of the safety information and instructions found in this instruction manual.
Explanation of symbols
An exclamation mark is intended to inform the
user of important information, operation or
maintenance instructions, or that special
attention is required.
This symbol is intended to alert you to the
presence of unprotected live parts or
components found within the product’s
enclosure, or of dangerous connections that
upon contact may be of sufficient magnitude
to constitute a risk of electric shock. Cables
intended for such connections should only be
connected by qualified personnel or you
should only use ready to connect cables.
There are no user-serviceable parts found
inside the device, therefore the device need
never be opened.

Page 6 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
2. Safety Information
The following safety and hazard warnings are not only
for the protection of your device, but also serve as a
protection against potential health hazards. Please
take time to read the following instructions carefully.
We assume no liability for personal or property
damage resulting from the failure to comply
with the safety instructions, or from improper
operation or handling. Under such
circumstances, all claims under warranty will
become void
-For safety and licensing (CE) reasons any
unauthorized modification and/or changes to
the device is prohibited and will void the
warranty and all warranty claims.
-Any persons operating, installing, setting up, or
servicing this device must be trained and
qualified accordingly, and observe these
operating instructions.
-Ensure that the device has been set up correctly
by following all the instructions found in the
instruction manual
-This is a protection class II device. Make sure that
the voltage supply of the power outlet used
meets the required voltage specifications
230V/~50 Hz.
-Power supply cables should be routed so that
they are not likely to be walked on, squashed or
pinched by items placed upon or against them.
Pay particular attention to cords at plugs, power
outlets, and at the point at which they exit from
the device. Avoid exposing the cable to
extreme heat or cold. Ignoring the above
mentioned instructions could result in cable
damage and present the danger of an electric
shock.
- Should any obvious damage be seen on the
device or on the connection cables, do not
contact them in any way. Switch of the
corresponding circuit breaker in the power
distribution panel first, before carefully
unplugging the power plug from the wall outlet.
Do not operate the device further! Please
contact or take it to a qualified service
technician or specialty workshop.
- In order to completely cut off the power supply
to the device, unplug the power plug from the
wall outlet. Merely turning the device off with the
ON/OFF button is not sufficient. Also make sure
that power outlets are easily accessible.
- Always pull on the plug’s grips and never on the
cable to remove it from a wall outlet. Unplug the
device from the power outlet if not in use for a
longer period of time.
- For safety reasons, always unplug the device
from the power outlet during thunder storms.
- Eliminate potential tripping hazards by routing
cables in such a way that no one can trip or
stumble over them.
- Never use the device, if the power cable or
device is damaged.
- Keep packaging and protective foil away from
children at all times to avoid the danger of
suffocation.
- The device should never come into contact with
water or moisture.
- To prevent the risk of fire or electric shock make
sure that liquids, such as dripping or splashing
water, rain or moisture, do not come in contact
with the device and power supply plug
- Operate this device in a moderate climate and
never expose it to extreme temperatures, such
as high humidity.
- Condensation can build up suddenly if the
device is brought from a colder area into a
warmer area (e.g. when transporting). Should
this happen, allow the device to warm up to
room temperature first before using.
- Care should be taken so that liquids do not
come in contact with the interior, this is why
containers containing liquids, e.g. buckets, vases
or plants should never be placed anywhere near
this product, including the power supply plug.
This could not only damage the device, but also
present a fire hazard.
- It is imperative to avoid contact with moisture,
e.g. never operate in the bathroom.
- Make sure the device is properly ventilated
during operation and never operate it in
constricted areas, such as for example in a
bookcase or shelf. Never block ventilation
openings with magazines, tablecloths, curtains
or similar.
- Make sure the device is placed on a firm and
stable surface.
- Never place any sources of fire on top of or near
the device and power supply plug (e.g. lighted
candle).
- Please note that excessive sound pressure
created when listening to loud volume levels
with earphones or headphones can lead to
permanent hearing damage.
- Please adhere to the additional safety
information found in the individual chapters of
this instruction manual.
- When connecting other devices, please refer to
the safety and operating instructions found in
the literature accompanying the device.
- Please contact our technical hotline or a service
technician for further information, should you be
in doubt about device operation, safety or when
making connections, or if any questions arise
that are not explained within this manual.
- Contribute to a better environment by using a
designated recycling site for the disposal of
packaging material.

Page 7 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
3. Accessories
The following accessories are supplied with the system.
Please check all these parts are present before
proceeding. Please inform your dealer if any part is
missing or damaged.
1 x Remote control handset
1 x mains power cable

Page 8 © Mitchell & Johnson UK 2012 SAP201V IB Ver 1.0 Rev 0.0
4. Description of parts
Front Panel
Rear Panel
1. Power cable inlet: Plug in the supplied power cable here.
2. Right Speaker terminal posts.
3. Left Speaker terminal posts.
4. RCA Pre-amp Output connector.
5. RCA Input connectors,
6. Digital Optical Input. Connect an optical cable (not supplied) to connect to a digital output such as the optical output on
a Mitchell & Johnson network player.
7. Digital Coaxial S/PDIF input. Connect a COAX cable (not supplied) to connect to a digital output such as the coaxial
output on a SACD or CD player.
8. Phono ground terminal for connecting the ground connection from a turntable.
1. 3.5mm stereo line in jack socket. Connect any
audio source using a 3.5mm jack connection
such as an MP3 player
2. ¼” stereo headphone socket.
3. Press to select LINE IN input.
4. Press to select PHONO input.
5. Press to select CD input.
6. Press to select NET-PLAYER input.
7. Press to select AUX input.
8. Press to select TV input.
9. Press to select OPTICAL or COAX inputs.
10. Input selector. Turn to control volume or press to enter
tone control menu.
11. Power switch. Depress to switch unit on and depress
again to switch off.

Page 9 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
Mitchell & Johnson RM200 Remote Control Handset
Buttons 1-6 are for controlling the Mitchell & Johnson SAP201V amplifier
1 Switch amp power to Standby or power on from Standby
2 Reduce Volume
3 Increase Volume
4 Mute Volume
5 Scroll through the Input functions on amp
6 Scroll through the Tone functions on amp
Buttons 7-11 are for controlling the Mitchell & Johnson CDD201V CD Player
7 Switch CD Player power to Standby or power on from Standby
8 Pause control
9 Stop button
10 Press to skip to previous track.
11 Play button
12 Press to skip to next track.
Using the Remote Controller
Point the remote controller toward the front of the unit, within the field shown in the drawing.
- Do not expose the remote control sensor to strong light, such as direct sunlight or inverted fluorescent light.
- Using the unit near equipment that emits infrared beams or with another remote controller may cause malfunctions.
- Make sure that the audio rack does not have colored glass, as this could prevent the remote controller from
functioning properly.
- The remote controller will not function if there are obstacles between it and the remote control sensor.
- Do not place objects such as books on top of the remote controller. Doing so could depress the buttons on the
remote continually and drain the batteries.

Page 10 © Mitchell & Johnson UK 2012 SAP201V IB Ver 1.0 Rev 0.0
Inserting/changing batteries
Remove the battery compartment cover carefully.
Remove the used battery.
Insert a new CR2025 lithium battery, observing the correct
polarity as displayed inside the remote.
Push in the cover until it clicks.
Information on handling batteries and rechargeable
batteries
Please adhere to the following information when handling
batteries and rechargeable batteries.
- Keep batteries out of children’s reach.
- Batteries are hazardous and do not
belong in household waste.
- Ensure correct polarity when inserting
batteries.
- Always remove batteries when the remote
control is not in use for long periods of
time.
- Never leave batteries lying around
unsupervised. If swallowed these could
pose a choking hazard to children and
pets. Seek emergency medical care
immediately, should this happen.
- Never expose batteries to extreme
temperatures, such as sunlight, fire, ovens,
etc. there is a risk of explosion!
- Make sure that batteries are not
dismantled, short-circuited or are thrown
into fire. Never re-charge non-
rechargeable batteries. There is a risk of
explosion!
- Always follow the manufacturer's
instructions when recharging
rechargeable batteries.
- Touching leaking or damaged batteries
could cause skin burns. Use protective
gloves suitable for handling such batteries.
- Always ensure that the device has been
turned off after use.
- Always change/replace all batteries at
the same time.
- If required clean battery and device
contacts before inserting,

Page 11 © Mitchell & Johnson UK 2012 SAP201V IB Ver 1.0 Rev 0.0
5. Set Up and Connection to Other Devices
This amplifier is designed to be connected to speakers for audio playback and other audio source devices such as a CD player
or tuner. There are two ways of connecting: analog and digital. You may use either depending on the capability of the device
you wish to connect.
Correct Connection of Analog RCA Audio Cables
- Pay attention to the plug colours and the left and right channels when connecting RCA audio cables.
- Ensure a good connection by making sure to insert plugs completely. Failure to insert fully can cause noise or
malfunctions.
- To prevent unwanted interference keep audio cables as far apart from power cables as possible.
Correct Connection of Digital Cables
- There are two types of digital audio connection terminals
oOPTICAL
and
oCOAXIAL
- Follow the instructions for the device you wish to connect to ensure the correct cable is used.

Page 12 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
Correct Connection of Speakers
- There are two ways to connect speaker cables to the connection terminals on the amplifier. Either by
connecting bare wire or by using cables with terminal connectors fitted.
Bare Wire Method
- Strip away approx. 5/8 inch (15 mm) of insulation from the ends of the speaker cables, and twist the bare wires
tightly.
- Loosen the screws on the speaker terminals, insert the wires, and screw the terminals tight.
Caution
- Make sure that the wires do not touch metal parts on the back panel or elsewhere.
Terminal Connectors Method
- For a much improved speaker cable connection it is
advisable to use speaker cables with terminal connectors
fitted such as banana plugs as shown on the right.
- Connect the speakers as shown in the drawing below. Connect the positive speaker wire to the RED +positive
terminal on the unit, and the negative speaker wire to the BLACK –negative on the unit.

Page 13 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
Connecting Analog Audio Components
- When connecting any component to the amplifier please ensure the power is switched off before connection.
Connecting a Turntable
CAUTION
- If the turntable has a ground wire, connect it to the unit's Phono GND screw. Note, however, that for some
turntables, connecting the ground wire will increase the noise. If this happens, disconnect the ground wire.
Connecting a CD or SACD player

Page 14 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
Connecting a Network Player/Internet radio/DAB+ Tuner
Connecting Digital Audio Components
- When connecting any component to the amplifier please ensure the power is switched off before connection.
- There are two types of digital connection. Optical and Coaxial. See below
Connecting a device via Digital Optical and/or Digital Coaxial Connection

Page 15 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
Connecting the Power Cable
- Before connecting the power cord, connect all the other components.
- Make sure the power switch is turned off on the unit before plugging or unplugging the power cable.
- Connect the supplied power cord to the unit's AC INLET.
Caution
- Never plug the power cord into the outlet before connecting it to the unit.
- If the power cord is plugged in, connecting or disconnecting it to/from the unit could cause electric shock.
- Plug the power cord into a household power outlet.

Page 16 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
6. Listening to Audio
- Turn on the component connected to the unit.
- Press the POWER button on the front of the unit to turn it on.
- The POWER indicator illuminates BLUE.
Notes:
Audio output will not begin until the electrical circuit stabilizes.
The display shows Mitchell & Johnson during this time.
Audio quality will stabilize about 10 to 30 minutes after the unit is turned on.
- Press the input button to select the audio playback component.
- Start playback on the component selected.

Page 17 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
- Turn the CONTROL knob to adjust the volume.
- You can also control the volume using the volume buttons on the remote controller.
- Press the MUTE button on the remote controller to set the volume to the minimum level.
- When the volume is muted, the display indicator reads
MUTE.
- Press the MUTE button again to restore the original volume.
- Mute mode will also be cancelled by adjusting the volume or pressing the POWER button.
Notes:
- When rotating the CONTROL knob the display ranges from -80dB to 0dB. Depending on the output signal level
from the attached audio component, comfortable listening levels will vary.
- When using the remote control to switch the unit to standby mode the POWER indicator light will change from
BLUE to RED. To switch the unit on from standby simply press the power button on the remote control handset.

Page 18 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
- To listen with headphones, turn down the volume, and then insert the headphone plug into the HEADPHONE
jack. When headphones are plugged in no sound will be heard from the speakers.
Adjusting the Tone and Left/Right Volume Balance
- Press the CONTROL knob to initiate the tone adjustment controls.
- Each press of the CONTROL knob will cycle through BASS, TREBLE and BALANCE.
- Turn the CONTROL knob to adjust each tone setting.
- The last option in the cycle is LOAD DEFAULT? Pressing the CONTROL knob again will reset the tone adjustment to flat.

Page 19 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
7. Troubleshooting and error messages
The SAP201V is equipped with state-of-the-art technology and is safe to operate. Nevertheless, problems or malfunctions
may occur. Before contacting Mitchell & Johnson customer support, refer to the following for possible solutions.
PROBLEM
POSSIBLE SOLUTION
No power when switched on
-Wall socket not switched on or faulty
-Plug not fully inserted into wall socket
-Fuse in plug may have blown.
-Internal mains fuse has blown inside the unit,
this will need to be replaced by a qualified service
technician
No sound
-Power not turned on
-Volume setting too low
-Loudspeaker cables not connected
-No input audio equipment is connected or is faulty
-Correct audio input source not selected on front panel
No sound in one channel
-Audio source input cables connected incorrectly or
damaged
-Audio input source faulty
Loudspeaker cables connected incorrectly or
damaged
-Loudspeakers are faulty
-Balance control switched to one side
Loud buzz or hum
-Audio input cables damaged or not correctly
connected
-CD player sited too close to TV
Weak bass, diffused stereo image
-Speaker connections out of phase check + and –terminals
are connected to corresponding terminals on both
amplifier and loudspeakers
Distorted sound
-Frayed wires may be touching on speaker terminals
causing distortion
-Bass and treble controls may be too high for
loudspeaker specification.
-Volume control may be set too high
Audio input source switches not
working
-Internal fault would need servicing by a qualified service
technician.
Remote control not working
-Check if the batteries have been inserted correctly.
-If batteries are empty, replace them with new ones.
-Remove any objects found between the remote control
and the remote sensor.
-Make sure the distance between the remote control and
the device does not exceed 8 m
Buttons do not function (on the unit and/or
remote control)
-Turn the unit off and then on again.
-As an alternative, turn the unit off, unplug it from the power
outlet and plug in again.
Any repairs other than those mentioned above are to be carried out solely by an authorised technician.

Page 20 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
8. Maintenance and Handling
Carry out a technical safety inspection on a regular basis, e.g. check if the power cable or housing has not been
damaged.
If there is reason to believe that the device can no longer be operated safely, then disconnect it immediately from the
power supply and secure it against any unintentional operation. Carefully remove the power cable plug from the wall
outlet and where applicable switch off the corresponding circuit breaker first.
It can be assumed that safe operation is no longer possible, if:
-there is visible damage to the device or power cable,
-the device has become wet or water has been able to get inside.
-it has been stored for a long period of time under unfavorable conditions
-it has been dropped, exposed to rigorous transport conditions or otherwise damaged.
Always adhere to the following safety instructions before cleaning and maintenance:
Live parts may be exposed, if the covering is opened or parts are removed.
-The device must be disconnected from the power supply source prior to service, maintenance
or repairs.
-Repairs are only to be carried out by qualified personnel, who are familiar with the hazards involved
and the relevant regulations.
Transporting or sending the device
Please retain the original box and the packaging material in case you need to transport or send the device out for
maintenance at a later date. Please note that the device should be repacked in the original packaging. The box and
packaging have been especially developed for this device in order to protect it during transport and against damage.
Retain this instruction manual for future reference and where required pass it along with the device if handed over to a
third party. It contains important information on initial operation and handling.
Keeping the external case clean
Never use volatile fluids near the device, as for example insect spray. Avoid letting the device come in contact with
rubber or plastic products for longer periods of time. These could otherwise leave marks behind.
Cleaning the device
Unplug the power cable before cleaning. Always use a soft and dry cloth to clean the unit’s exterior. If the device is
extremely dirty you can use a soft cloth, dampened with water or a mild cleaning solution to clean. Never use any
abrasive or harsh cleaning agents (e.g. alcohol, benzene or thinners) as these could damage the controls, casing or any
markings and labels found on the device.

Page 21 © Mitchell & Johnson UK 2013 SAP201V IB Ver 1.0 Rev 0.0
Important Notice
Please note that electrical and electronic devices must never be disposed of in regular household waste!
Consumers are legally obligated and responsible for the proper disposal of electronic devices by returning them
to collection sites designated for the recycling of electrical and electronic equipment waste after the useful life
of the device has come to an end. For more information concerning collection sites and correct disposal please
contact your local authority or waste management company. The presence of the above symbol on a device,
or its packaging or within the instruction manual indicates that the item must not be disposed of in normal
unsorted municipal waste.
In doing so you are fulfilling all recycling and disposal obligations and are optimising and contributing to a better
environment. These disposal regulations apply to batteries and rechargeable battery disposals as well. Most
batteries contain hazardous chemicals which can contaminate the environment and human health if they are
discarded in ordinary household waste. According to legislation batteries are to be returned to the place of
purchase or disposed of at a designated recycling site