Mitsubishi Electric WD-57733 User manual

DLP®HIGH-DEFINITION TELEVISION
MODELS
C Series
WD-C657
Y Series
WD-Y577, WD-Y657
733 Series
WD-57733, WD-65733, WD-73733
734 Series
WD-57734, WD-65734, WD-73734
OWNER’S GUIDE
• Forquestions:
- Visitourwebsiteatwww.mitsubishi-tv.com.
- E-mailusat[e-mail].
- CallConsumerRelationsat800-332-2119.
• ForinformationonSystem Reset,pleaseseethebackcover.
• Toorderreplacementoradditionalremotecontrols,lampcartridges,orOwner’sGuides,
visitourwebsiteatwww.mitsuparts.comorcall800-553-7278.
• GuidelinesforsettingupandusingyournewwidescreenTVstartonpage11.
x.v.Color

For Your Records
Recordthemodelnumber,serialnumber,and
purchasedateofyourTV.Themodelandserial
numbersareonthebackoftheTV.Refertothis
pagewhenrequestingassistancewiththeTV.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
FCC Declaration of Conformity
Product: ProjectionTelevisionReceiver
Models: WD-C657
WD-57733, WD-65733, WD-73733
WD-Y577, WD-Y657
WD-57734, WD-65734, WD-73734
Responsible
Party:
MitsubishiDigitalElectronicsAmerica,
Inc.
9351JeronimoRoad
Irvine,CA92618-1904
Telephone: [phone]
ThisdevicecomplieswithPart15oftheFCCRules.
Operationissubjecttothefollowingtwoconditions:
(1)
Thisdevicemaynotcauseharmfulinterference,
and
(2) thisdevicemustacceptanyinterference
received,includinginterferencethatmaycause
undesiredoperation.
Note:Thisequipmenthasbeentestedandfound
tocomplywiththelimitsforaClassBdigitaldevice,
pursuanttopart15oftheFCCRules.Theselimits
aredesignedtoprovidereasonableprotection
againstharmfulinterferenceinaresidentialinstal-
lation.Thisequipmentgenerates,usesandcan
radiateradiofrequencyenergyand,ifnotinstalled
andusedinaccordancewiththeinstructions,may
causeharmfulinterferencetoradiocommunica-
tions.However,thereisnoguaranteethatinterfer-
encewillnotoccurinaparticularinstallation.Ifthis
equipmentdoescauseharmfulinterferencetoradio
ortelevisionreception,whichcanbedetermined
byturningtheequipmentoffandon,theuseris
encouragedtotrytocorrecttheinterferencebyone
ormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequip-
mentandthereceiver.
• Connecttheequipmentintoanoutleton
acircuitdifferentfromthattowhichthe
receiverisconnected.
• Consultthedealeroranexperiencedradio/
TVtechnicianforhelp.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TOREDUCETHERISKOFELECTRIC
SHOCK,DONOTREMOVECOVER(ORBACK).
NOUSERSERVICEABLEPARTSINSIDE.
REFERSERVICINGTOQUALIFIEDSERVICE
PERSONNEL.
Thelightningflashwitharrowhead
symbolwithinanequilateraltriangleis
intendedtoalerttheuserofthepres-
enceofuninsulated“dangerousvoltage”
withintheproduct’senclosurethatmay
beofsufficientmagnitudetoconstitute
ariskofelectricshocktopersons.
Theexclamationpointwithinanequilateral
triangleisintendedtoalerttheuserto
thepresenceofimportantoperatingand
maintenance(servicing)instructionsinthe
literatureaccompanyingtheproduct.
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
TV WEIGHT:ThisTVisheavy!Exerciseextremecare
whenliftingormovingit.LiftormovetheTVwitha
minimumoftwoadults.TopreventdamagetotheTV,
avoidjarringormovingitwhileitisturnedon.Always
poweroffyourTV,unplugthepowercord,anddiscon-
nectallcablesbeforemovingit.
WARNING:Thisproductcontainschemicalsknown
totheStateofCaliforniatocausecancerand/orbirth
defectsorotherreproductiveharm.

Contents
Important Information About Your TV
GeneralWarningsandCautions,Noteson
InstallationandOperation................. 4
ImportantSafeguards..................... 5
1 Television Overview
PackageContents....................... 6
SpecialFeaturesofYourTV................. 6
TVFrontPanel.......................... 7
TVBackPanel.......................... 9
2 TV Setup
GuidelinesforSettingUpandUsingYourNew
WidescreenTV........................ 11
InstallingtheRemoteControlBatteries........ 12
WhenYouFirstPowerOntheTV............ 12
InitialTVSetup......................... 12
SettingUpTVInputs..................... 13
ControllingA/VReceiverSoundVolume....... 14
UsingtheTVwithaPersonalComputer....... 15
3 TV Connections
BeforeyouBegin....................... 17
HDTVCableBoxorSatelliteReceiverwith
ComponentVideo..................... 17
StandardCableBox,SatelliteReceiver,orOther
DevicewithS-Video.................... 18
H DMIDevice(CableBox,SatelliteReceiver,
DVDPlayer,orOtherDevice )............... 18
WallOutletCable(nocablebox)............ 19
AntennawithaSingleLead................ 19
AntennaswithSeparateUHFandVHFLeads... 19
DVDPlayerwithComponentVideo.......... 20
DVIVideoDevice(CableBox,SatelliteReceiver,
DVDPlayer,orOtherDevice).............. 20
VCRtoanAntennaorWallOutletCable....... 21
VCRtoaCableBox(Audio&Video).......... 22
A/VReceiver(SoundSystem).............. 23
OlderCableBox........................ 23
Camcorder........................... 24
4 TV Operation and Features
ChoosingaViewingSource................ 25
SleepTimer........................... 25
RemoteControl........................ 26
ChannelView™ChannelListings............ 27
StatusDisplay......................... 28
FAV(FavoriteChannels)................... 29
TVSignalsandDisplayFormats............. 30
ViewingCameraFiles.................... 32
JPEGPhotosandtheUSBPhotoPort..... 32
PhotosandMovingVideoasComposite
Video............................ 33
5 TV Menu Settings
RemoteControlKeysfortheTVMenuSystem. . 34
MainMenu............................ 34
AVMenu............................. 35
VideoMenu........................ 36
AudioMenu........................ 37
CaptionsMenu......................... 38
SetupMenu........................... 39
InputsMenu........................... 43
LockMenu............................ 44
SettingorResettingaPassCode......... 44
ParentMenu....................... 44
OtherMenu(AlternateRatingSystem)..... 44
BypassingTVLocks.................. 44
6 NetCommand
AboutNetCommand..................... 47
IREmitterPlacement(NetCommand®)........ 48
InitialNetCommandSetupforMostDevices.... 49
AddorRemoveDeviceKeysfromNetCommand
Control............................. 49
NetCommandSpecializedDeviceKeys....... 50
OperatingNetCommand-ControlledDevices... 51
SetUpNetCommandControlofanA/VReceiver 53
Appendices
AppendixA:Specifications................ 58
AppendixB:BypassingtheParentalLock..... 59
AppendixC:Lamp-CartridgeReplacementand
Cleaning............................ 61
AppendixD:ProgrammingtheRemoteControl. 63
AppendixE:Troubleshooting.............. 71
Trademark and License Information.......... 77
Mitsubishi TV Software.................... 78
Mitsubishi DLP™ Projection Television Limited
Warranty............................. 79
Index................................. 81

Operating Notes
Internal Fans
Internalcoolingfansmaintainproperoperatingtempera-
turesinsidetheTV.Itisnormaltohearthefanswhenyou
firstturnontheTV,duringquietsceneswhileviewingthe
TV,andforashorttimeafterturningofftheTV.
TV Software
DonotattempttoupdatethesoftwareofthisTVwith
softwareorUSBdrivesnotprovidedbyorauthorized
byMitsubishiDigitalElectronicsAmerica,Inc.Non-
authorizedsoftwaremaydamagetheTVandwillnotbe
coveredbythewarranty.
Cleaning Recommendations
Normally,lightdustingwithadry,non-scratchingduster
willkeepyourTVclean.Ifcleaningbeyondthisis
needed,pleaseusethefollowingguidelines:
First,turnofftheTVandunplugthepowercordfrom
thepoweroutlet.
Top and Sides of the TV
• Occasionallycleandustbuild-upfromtheair-intake
grillesonthebackandsidesoftheTV.Cleanusing
avacuumcleanerwithabrushattachment.
• GentlywipedownyourTVwithasoft,non-abrasive
clothsuchascottonflanneloracleanclothdiaper,
lightlymoistenedwithwater.Drywithaseconddry,
soft,non-abrasivecloth.
• Foroilydirt,addafewdropsofmildliquiddeter-
gent,suchasdishwashingdetergent,tothewater
usedtomoistenthecloth.Rinsewithasecond
clothmoistenedonlywithwater.Drywithathird
dry,soft,non-abrasivecloth.
Screen
• Followtheinstructionsforthetopandsides,wiping
gentlyinanupanddownmotion.
• Cleantheentirescreenevenly,notjustsectionsof
thescreen.
• Donotallowliquidtodripdownthescreen,as
someliquidmayentertheTVthroughthegap
betweenthescreenandscreenframe.
• YoumaypurchaseMitsubishiScreenCleaner,part
numberCLEANER-VSS,bycalling(800)553-7278.
General Cleaning Precautions
• DONOTallowliquidtoentertheTVthroughthe
ventilationslotsoranycrevice.
• DONOTuseanystrongorabrasivecleaners,as
thesecanscratchthesurfaces.
• DONOTuseanycleanerscontainingammonia,
bleach,alcohol,benzene,orthinners,asthesecan
dullthesurfaces.
• DONOTsprayliquidsorcleanersdirectlyonthe
TV’ssurfaces.
• DONOTscruborrubtheTVharshly.Wipeitgently.
IMPORTANT
DO NOT use any kind of abrasive cleaner on the
surface of the TV screen.
Lamp Replacement
Forlamp-replacementinstructions,seeAppendixC.
To Order a Replacement Lamp Under Warranty
Call(800)553-7278.Pleasehavemodelnumber,serial
number,andTVpurchasedateavailable.
Important:Alllampsreplacedunderwarrantymustbe
returnedtoMitsubishiwheretheywillbeinspectedfor
defectverification.
To Purchase a Replacement Lamp After Warranty
Visitourwebsiteatwww.mitsuparts.comorcall
(800)553-7278.Ordernewlamppartnumber
915P061010.
Important Information About Your TV
Installation Notes
Stand Requirement
CAUTION:UsetheseMitsubishiTVmodelsonlywith
theMitsubishistandmodelsshownhere.Otherstands
canresultininstabilityandpossiblycauseinjury.
TV Model Stand Model
WD-57733
WD -Y577
WD-57734
MB-57PB
WD-65733
WD -Y657
WD-65734
MB-65PB
WD-C657 MB-65G
WD-73733
WD-73734 MB-73PB
Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS
REMINDERISPROVIDEDTOCALLTHECATVSYSTEM
INSTALLER’SATTENTIONTOARTICLE820-40OFTHE
NECTHATPROVIDESGUIDELINESFORTHEPROPER
GROUNDINGAND,INPARTICULAR,SPECIFIESTHAT
THECABLEGROUNDSHALLBECONNECTEDTO
THEGROUNDINGSYSTEMOFTHEBUILDING,AS
CLOSETOTHEPOINTOFCABLEENTRYASPRACTI-
CAL.

Important Safeguards
PleasereadthefollowingsafeguardsforyourTVandretainforfuturereference.Alwaysfollowallwarningsandinstructions
markedonthetelevision.
1. Read, Retain and Follow All Instructions.ReadallsafetyandoperatinginstructionsbeforeoperatingtheTV.Retainthesafetyandoperating
instructionsforfuturereference.Followalloperatinganduseinstructions.
2. Heed Warnings. Adheretoallwarningsontheapplianceandintheoperatinginstructions.
3. Cleaning. UnplugtheTVfromthewalloutletbeforecleaning.Donotuseliquid,abrasiveoraerosolcleaners.Cleanerscanpermanently
damagethecabinetandscreen.Usealightlydampenedclothforcleaning.
4. Attachments and Equipment. Neveraddanyattachmentsand/orequipmentwithoutapprovalofthemanufacturerassuchadditionsmay
resultintheriskoffire,electricshockorotherpersonalinjury.
5. Water and Moisture. DonotusetheTVwherecontactwithorimmersioninwaterispossible.Donotusenearbathtubs,washbowls,kitchen
sinks,laundrytubs,inawetbasement,swimmingpools,etc.
6. Accessories. DonotplacetheTVonanunstablecart,stand,tripod,ortable.TheTVmayfall,causingseriousinjurytoa
child,adultorpetandseriousdamagetotheTV.Useonlywithacart,stand,tripod,bracketortablerecommendedbythe
manufacturer,orsoldwiththeTV.AnymountingoftheTVshouldfollowthemanufacturer’sinstructions,andshoulduse
mountingaccessoriesrecommendedbythemanufacturer.
Anapplianceandcartcombinationshouldbemovedwithcare.Quickstops,excessiveforce,andunevensurfacesmaycause
theapplianceandcartcombinationtooverturn.
7. Ventilation. SlotsandopeningsinthecabinetareprovidedforventilationandtoensurereliableoperationoftheTVandtoprotectitfrom
overheating.DonotblocktheseopeningsorallowthemtobeobstructedbyplacingtheTVonabed,sofa,rug,orothersimilarsurface.Nor
shoulditbeplacedoveraradiatororheatregister.IftheTVistobeplacedinarackorbookcase,ensurethatthereisadequateventilationand
thatthemanufacturer’sinstructionshavebeenadheredto.
8. Power Source. ThisTVshouldbeoperatedonlyfromthetypeofpowersourceindicatedonthemarkinglabel.Ifyouarenotsureofthetypeof
powersuppliedtoyourhome,consultyourappliancedealerorlocalpowercompany.
9. Grounding or Polarization. ThisTVisequippedwithapolarizedalternatingcurrentlineplughavingonebladewiderthantheother.Thisplug
willfitintothepoweroutletonlyoneway.Thisisasafetyfeature.Ifyouareunabletoinserttheplugfullyintotheoutlet,tryreversingtheplug.If
theplugshouldstillfailtofit,contactyourelectriciantoreplaceyourobsoleteoutlet.Donotdefeatthesafetypurposeofthepolarizedplug.
10. Power-Cord Protection. Power-supplycordsshouldberoutedsothattheyarenotlikelytobewalkedonorpinchedbyitemsplaceduponor
againstthem,payingparticularattentiontocordsatplugs,conveniencereceptacles,andthepointwheretheyexitfromtheTV.
11. Lightning. ForaddedprotectionforthisTVduringalightningstorm,orwhenitisleftunattendedandunusedforlongperiodoftime,unplugit
fromthewalloutletanddisconnecttheantennaorcablesystem.ThiswillpreventdamagetotheTVduetolightningandpower-linesurges.
12. Power Lines.Anoutsideantennasystemshouldnotbelocatedinthevicinityofoverheadpowerlinesorotherelectriclightorpowercircuits,
orwhereitcanfallintosuchpowerlinesorcircuits.Wheninstallinganoutsideantennasystem,extremecareshouldbetakentokeepfrom
touchingsuchpowerlinesorcircuitsascontactwiththemmightbefatal.
13. Overloading. Donotoverloadwalloutletsandextensioncordsasthiscanresultinariskoffireor
electricshock.
14. Object and Liquid Entry. NeverpushobjectsofanykindintothisTVthroughopeningsasthey
maytouchdangerousvoltagepointsorshort-outpartsthatcouldresultinfireorelectricshock.
NeverspillliquidofanykindonorintotheTV.
15. Outdoor Antenna Grounding. IfanoutsideantennaorcablesystemisconnectedtotheTV,be
suretheantennaorcablesystemisgroundedsoastoprovidesomeprotectionagainstvoltage
surgesandbuilt-upstaticcharges.
Article810oftheNationalElectricCode,ANSI/NFPANo.70-2002,providesinformationwith
respecttopropergroundingofthemastandsupportingstructure,groundingoftheleadinwireto
anantennadischargeunit,sizeofgroundingconductors,locationofantennadischargeunit,con-
nectiontogroundingelectrodes,andrequirementsforthegroundingelectrode.
16. Servicing. DonotattempttoservicethisTVyourselfasopeningorremovingcoversmayexposeyoutodangerousvoltageorotherhazards.
Referallservicingtoqualifiedservicepersonnel.
17. Damage Requiring Service. UnplugtheTVfromthewalloutletandreferservicingtoqualifiedservicepersonnelunderthefollowing
conditions:
(a) Whenthepower-supplycordorplugisdamaged.
(b) Ifliquidhasbeenspilled,orobjectshavefallenintotheTV.
(c) IftheTVhasbeenexposedtorainorwater.
(d) IftheTVdoesnotoperatenormallybyfollowingtheoperatinginstructions,adjustonlythosecontrolsthatarecoveredbytheoperating
instructionsasanimproperadjustmentofothercontrolsmayresultindamageandwilloftenrequireextensiveworkbyaqualifiedtechni-
ciantorestoretheTVtoitsnormaloperation.
(e) IftheTVhasbeendroppedorthecabinethasbeendamaged.
(f) WhentheTVexhibitsadistinctchangeinperformance-thisindicatesaneedforservice.
18. Replacement Parts. Whenreplacementpartsarerequired,besuretheservicetechnicianhasusedreplacementpartsspecifiedbythe
manufacturerorhavethesamecharacteristicsastheoriginalpart.Unauthorizedsubstitutionsmayresultinfire,electricshockorotherhazards.
19. Safety Check. UponcompletionofanyserviceorrepairtotheTV,asktheservicetechniciantoperformsafetycheckstodeterminethattheTV
isinsafeoperatingcondition.
20. Heat. Theproductshouldbesituatedawayfromheatsourcessuchasradiators,heatregisters,stovesorotherproducts(includingamplifiers)
thatproduceheat.
AN T E N NA
LE AD IN WIR E
AN T E N NA
DI S C H AR G E UNI T
(N E C A R T I C L E 81 0-2 0)
G R O U NDIN G
C O NDUC T O R S
(N E C A R T I C L E 81 0-2 1)
G R O U ND C L AM P S
P OW E R S E R V IC E G R O UNDING
E LE C TR ODE S Y S TE M
(N E C A R T 250, P AR T H)
G R O U ND C L AM P
E LE C TR IC
S E R V IC E
E QUIP ME NT
NE C — NAT IO NA L E L E C T R IC AL C O DE
E XAMP LE OF ANT E NNA G R O UNDING

6
Package Contents
Pleasetakeamomenttoreviewthefollowinglistof
itemstoensurethatyouhavereceivedeverything.
Special Features of Your TV
Yournewhigh-definitionwidescreentelevisionhas
manyspecialfeaturesthatmakeittheperfectcenterof
yourhomeentertainmentsystem,including:
1080p High-Definition DLP™ Display
System
YourMitsubishiHDTVusesTexasInstrumentsDigital
LightProcessing™technologyforrear-projectionTVs
tocreatethepictureyouseeonscreen.Allimages
aredisplayedat1080p.TheTVusesPlush1080pto
convertlower-resolutionsignalsto1080pfordisplay.
TheTVcanalsoaccept1080poriginalsignalsand
maintainthemat1080pthroughallprocessinguntil
displayed.
16:9 Widescreen Picture Format
Enjoyafulltheatricalexperienceinthecomfortofyour
home.Viewpicturesasfilmdirectorsintendedthem.
DigitalTVbroadcasts,DVDsandnewervideogame
consolessupportthiswidescreenformat.
Integrated HDTV Tuner
YourwidescreenMitsubishiHDTVhasaninternalHDTV
tunerabletoreceivebothover-the-airHDTVbroad-
casts(receivedviaanantenna)andnon-scrambled
digitalcablebroadcasts,includingnon-scrambled
HDTVcableprogramming.
High-Definition Video Inputs
Component Video Inputs.AlsocalledY/Pb/Pr
inputs,theseinputsreceivestandardanalogvideo
formatsof480i,480p,720p,and1080ihigh-defini-
tionsignals.Thisprovidesahighlevelofflexibility
whenconnectingDVDplayers/recorders,cable
boxes,andsatellitereceivers.
HDMI 1.3 Inputs.Theseinputsacceptdigital480i,
480p,720p,1080i,and1080pvideosignalsplus
PCMdigitalstereosignals.TheHDMIinputscan
alsoacceptavarietyofPCsignalsandresolutions.
ManycomputersignalsarecompatiblewithDeep
Colorandx.v.Color.
Usedwithanadapter,theseinputsalsoaccept
compatibledigitalDVIvideosignals.HDMI
inputsprovideadditionalhigh-performance,
high-definitionconnectionsformaximumflexibility
inyourchoiceofhometheaterproducts.TheHDMI
inputsareHDCPcopy-protectioncompatible.
Easy Connect Auto Input Sensing
EasyConnect®automaticallyrecognizeswhenyou
pluginaninputandpromptsyoutoassignanametoit.
TheTVignoresanyunusedinputs,sotheresultisan
unclutteredInput Selectionmenuwhereyoucaneasily
findandselectconnecteddevicesbyname.
Home Theater Control
NetCommand with IR Learning (Y series and 734
series models only)
SelectedMitsubishiHDTVsofferanewlevelofnet-
workingthatseamlesslyintegratesselectedolder
A/Vproductswithnewandfuturedigitalproducts.
NetCommand®supportsIR(infrared)controlofprod-
uctssuchasVCRs,DVDplayers,cableboxes,and
satellitereceivers.NetCommandcan“learn”remote
controlsignalsdirectlyfrommanydevices,allowingyou
tocreateacustomizedNetCommand-controlledhome-
theatersystem.
NetCommand for HDMI Devices (all models)
SomenewerHDMIdevicesmaybecompatiblewith
theTV’sNetCommandforHDMIfeature.Compatible
devicescanreceivecontrolsignalsthroughtheHDMI
connection.TheTV’sremotecontrolmaybeableto
operatesomefunctionsofthesedeviceswithoutany
furthersetup.
Television Overview
1
1. Remote Control
2. Two AA Batteries
3. Owner’s Guide
4. Quick Reference Guide
5. Quick Connect Guide
6. Product Registration Card
7. Two-Ended IR Emitter
(included with Y series and
734 models only)
1
AA AA
2
7

1. Television Overview 7
TV Front Panel
A/V Reset
IfyouwishtoresettheA/V(Audio/Video)settingsback
tothefactorydefaults:
• Toresetallsettingsatonce,press GUIDE and FORMAT
onthefrontpanelatthesametime.
• Toresetthedefaultsforindividualinputs,usethe
ResetselectionontheAVmenu.
Front Panel Indicators and Power Button
1. POWERbutton.TurnsTVonandoff;worksthe
sameasthe POWER keyontheremotecontrol.
2. POWER/TIMERindicator.LitwhenTVis
poweredon;flasheswhenTVispoweredoffand
theauto-onTVTimerisset.
3. STATUS indicator(offduringnormalTVoperation);
blinksrapidlywhenTVisfirstpluggedintoanAC
outlet.
4. LAMPindicatorshowslampcondition(usuallyoff
duringnormalTVoperation).
Seethenextpageformoreonfront-panelindicators.
Control Panel
Buttonsonthefront
controlpanelduplicate
commonlyusedkeyson
theremotecontrol.The
upperlabelsshowcontrol
functionswhennoTV
menusaredisplayed;the
lowerlabelsindicatefunc-
tionswhenTVmenusaredisplayedorwhenaspecial
functionhasbeenactivated.Seechapter4,“TVOpera-
tionandFeatures,”forthefunctionsofthesebuttons.
Front Inputs
• INPUT3 providesaneasilyaccessiblesetofinput
jacksforacamcorder,game,orotheraudio/video
device.
• AUSBphotoportisincludedforviewingJPEG
images.
• AfourthHDMIinputisalsoprovidedonYand734
seriesmodels.
I
N
P
U
T
L-AUDIO-R VIDEO 3USB
Front inputs on C series model WD-C657
I
N
P
U
T
L-AUDIO-R VIDEO/Y Pb Pr 3USB
HDMI 4
DVI AUDIO
HDMI4inputavailableonYand
734seriesmodelsonly.
Component video inputs are offered on the front panel of
Y series, 733 series, and 734 series models. When using
a standard video device, connect the single (yellow) video
cable to the VIDEO/Y jack.
Flip down cover to
use buttons and
inputs on the front
panel.
System Reset Button
IftheTVdoesnotrespondtothe
remotecontrol,frontpanelcontrols,
orwillnotpoweron/off,pressthe
SYSTEM RESET buttononthefrontpanel.
Thegreen STATUS LEDwillflashquicklyforaboutone
minute.Whenthegreen STATUS LEDstopsflashing,you
mayturnontheTV.Recentsettingchangesyoumade
beforeusing SYSTEM RESET maybelost.
Front Control Panel. Buttons on the
front panel duplicate some keys on
the remote control.
VOL
ADJ ADJ
CH FORMAT MENU GUIDE INPUT SYSTEM
RESET
ENTER MENU CANCEL
VOL
ADJ ADJ
CH FORMAT MENU GUIDE INPUT SYSTEM
RESET
ENTER MENU CANCEL
4:45&.
3&4&5
Indicator lights and POWER button
13
4 2

81. Television Overview
Front-Panel Indicators
LAMP Indicator
LED Color TV Condition Additional Information
None NormalTVonorstandbycondition. Normaloperation.
Green TVjustpoweredoffandlampis
cooling.
Startstoblink30secondsafterturningoffTV.TVcanbeturned
onbeforeblinkingstartsorafterblinkingstops,butnotwhilethe
indicatorisblinking.Normaloperation.
Yellow 1. Lampaccessdoorisopenor
notsecure.
TVwillnotoperateuntillampaccessdoorissecure.See
AppendixCforinstallationinformation.
2. Nolampinstalled. TVwillnotoperatewithoutalamp.SeeAppendixCforinstalla-
tioninformation.
Red Lampnolongerilluminatesandhas
reachedtheendofthelamplife.
Replacethelamp.TheTVwillnotoperatewhenthelampno
longerilluminates.SeeAppendixCforinstallationinformation.
Off SteadyOn SlowBlinking FastBlinking
STATUS Indicator
LED Color TV Condition Additional Information
None NormalTVonorstandbycondition. Normaloperation.
Yellow TVistoohot.
TheTVwilldisplayawarningmessageandshutoffifitoverheats.
• Ambientroomtemperaturemaybetoohigh.TurnofftheTV
andwaituntiltheroomtemperaturedrops.
• Clearblockedairvents.Ensureatleastafour-inchclear-
anceonallsidesoftheTV.
• Cleanthelamp-cartridgeairfilter.SeeAppendixC.
Red
TVmayrequireservice. TurnofftheTVandunplugthesetfromtheACpowersource.
Waitoneminuteandthenplugthesetbackin.SeeAppendixE.
IftheLEDisstillon,contactyourdealeroraMitsubishi
AuthorizedServiceCenter.Gotowww.mitsubishi-tv.comorcall
1-800-332-2119toreceiveAuthorizedServiceCenterinformation.
TIMER Indicator
LED Color TV Condition Additional Information
None TVispoweredoff. Normaloperation.
Green TVispoweredon. Normaloperation.
Green TVpoweredoff,auto-ontimerisset. Normaloperation.TVcanbeturnedonatanytime.
Green 1. TVjustpluggedintoACoutlet. Waitapproximatelyoneminuteforblinkingtostopbeforeturning
on.Normaloperation.
2.
ACjustrestoredafterpowerfailure.
3. TVrebootingafterSystemReset
used.
4. TVrebootingafterpowerfluc-
tuationorreceivingabnormal
digitalsignalsfromadigital
channelordigitaldevice.
5. Youhavebeguntheprocedure
toupdatesoftwarefroman
authorizedflashmemorydevice.

1. Television Overview 9
TV Back Panel
1. ANT 1/MAIN, ANT 2/AUX (Antenna)
Ifyouareconnectinganantennaordirectcablewithout
acablebox,connectthemainantennaorcablesource
to ANT 1/MAIN .
ANT 1/MAIN and ANT 2/AUX caneachreceivedigital
andanalogover-the-airchannelsfromaVHF/UHF
antennaornon-scrambleddigital/analogcablesource.
2. COMPONENT Inputs (Audio and Video)
Y Pb Pr (480i/480p/720p/1080i)
Usethesejackstoconnectdeviceswithcomponent
videooutputs,suchasDVDplayers,externalHDTV
receivers,orcompatiblevideogamesystems.See
AppendixAspecificationsforsignalcompatibility.
3. PC/DVI AUDIO INPUT
Usethe PC/DVI AUDIO INPUT whenconnectingaDVI
devicetooneoftheTV’sHDMIinputsusingaDVI-to-
HDMIcable.Thesejacksallowyoutosendleftand
rightanalogaudiofromyourcomputerorotherDVI
devicetotheTV.
4. AVR AUDIO OUTPUT
Use AVR AUDIO OUTPUT tosendanalogaudioofthe
programcurrentlyshownonthescreentoanA/Vsur-
roundsoundreceiverorstereosystem.Digitalaudio
fromdigitalchannelsandHDMIdevicesisconvertedto
analogaudiobytheTV.IfusingananalogA/Vreceiver
orstereosystem,thisistheonlyaudioconnection
neededbetweenitandtheTV.
ANT 2 / AUX
ANT 1 / MAIN
ANT 2/ AUX
ANT 1 / MAIN
ANT 2 / AUX
ANT 1 / MAIN
INPUT 1
INPUT 2
L(MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AV R
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand R
PC/DVI
AUDIO
INPUT
COMPONENT 1
COMPONENT 2
ANT 2 / AUX
ANT 1 / MAIN
1
2
3
4
5
6
7 8
IREmitterJackincluded
onYseriesand734series
modelsonly.
ThirdHDMIinputavailableon
Y,733,and734seriesmodels.

10 1. Television Overview
5. INPUT 1, 2 (Audio and Video)
INPUT 1 and 2 canbeusedtoconnectaVCR,Super
VHS (S-VHS) VCR,DVDplayer,standardsatellite
receiver,orotherA/VdevicetotheTV.EachTV INPUT
groupconsistsofjacksforcompositevideo,S-Video,
andanalogstereoaudio.Notethatwhenyouconnect
totheS-videojack,thecompositevideojackisauto-
maticallydisabled. INPUT 3 isathirdsetofcomposite
videoandstereoaudiojackslocatedonthefrontofthe
TVforconvenience.
6. HDMI™ Inputs
TheHDMI1.3(HighDefinitionMultimediaInterface)sup-
portsuncompressedstandardandhigh-definitiondigital
videoformatsandPCMdigitalstereoaudioformat.
UsetheHDMIinputstoconnecttoEIA/CEA-861HDMI
compliantdevicessuchasahigh-definitionreceiver
orDVDplayer.Theseinputssupport480i,480p,720p,
1080i,and1080pvideoformats.
Mitsubishirecommendsyouusecategory2HDMIcables
toconnectHDMI1.3sourcedevices.High-speedcat-
egory2cablesbringyouthefullbenefitsofDeepColor
andx.v.Color.
TheseinputscanalsoacceptdigitalDVIvideoinputs.
ToconnectaDVIinput,useanHDMI-to-DVIadapteror
cableplusanalogaudiocables.Connecttheanalog
audiocablestothe PC/DVI AUDIO INPUT ontheTVto
receiveleftandrightstereoaudiofromyourDVIdevice.
TheTV’sHDMIinputsarecompatiblewithmanyDVI-D
andHDMIcomputervideosignals.Seechapter2,“TV
Setup”andAppendixAforadditionalinformationonPC
compatibility.
TheseinputsareHDCP(High-BandwidthDigitalCopy
Protection)compliant.
Theseinputsare certifiedforproperinterop-
erabilitywithotherproductscertifiedbySimplay™.
TV Back Panel, continued
HDMI Cable Categories
HDMIcablesareavailableasCategory1and
Category2versions.
• Category 2 Cables.Newer,HDMI1.3-com-
pliantDVDplayers,videogames,andset-top
boxesrequireCategory2cables.Usecategory
2cablesforthesehigh-speedHDsignalscar-
ryingextendedcolorencodings(i.e.,30ormore
bits,alsocalledDeepColor).Category2cables
arealsosuitableforstandardHDTVsignals.
• Category 1 Cables.Unmarkedcablesare
category1cablesandaresuitableforstandard
HDTVsignals.
7. DIGITAL AUDIO OUT
ThisoutputsendsDolbyDigitalorPCMdigitalaudioto
yourdigitalA/Vsurroundsoundreceiver.Analogaudio
fromanalogchannelsanddevicesisconvertedbytheTV
toPCMdigitalaudio.IfyouhaveadigitalA/Vreceiver,
inmostcasesthisistheonlyaudioconnectionneeded
betweentheTVandyourA/Vreceiver.
8. IR Emitter NetCommand®
Y series and 734 series models only
IREmittersconnectedtothisjackareusedbytheTV’s
NetCommandsystemtocontrolexternalIRremote
controlledanalogdevicessuchascableboxes,VCRs,
DVDs,satellitereceiversandaudioreceivers.

11
TV Set-Up
Getting Started
1. Reviewtheimportantsafety,installation,andoper-
atinginformationatthebeginningofthisbook.
2. ChoosealocationforyourTV.
• Allowatleastfourinchesofspaceonallsides
oftheTVtohelppreventoverheating.Over-
heatingmaycauseprematurefailureoftheTV
aswellasshortenedlamplife.
• Avoidlocationswherelightmayreflectoffthe
screen.
• Seethestandrequirementsunder“Important
Information About Your TV.”
3. Installthebatteriesintheremotecontrol.Seethe
followingpage.Seechapter4,“TVOperationand
Features”formoreonuseoftheremotecontrol.
4. PlugyourTVintoapoweroutlet.The TIMER indica-
toronthefrontoftheTVwillstartblinkingrapidly.
Afterthe TIMER indicatorstopsblinking,pressthe
POWER keytopowerontheTV.
5. WhentheWelcomescreenappearsthefirsttime
youpowerontheTV,selectalanguageforTV
menus.Youcanlaterchangethelanguagethrough
theSetupmenu.
6. Connectyouraudio/video(A/V)devicestotheTV
andperforminitialsetup.
• Seechapter3,“TVConnections”forconnec-
tiondiagrams.
• SeethefollowingpagesforinitialTVsetupand
useoftheAutoInputSensingfeature.
• Seechapter6,“NetCommand,”toperform
NetCommandIR“learning”forcontrolofyour
hometheater(availableonYseriesand734
seriesmodels).
7. Mitsubishirecommendsyouperformachannel
scan.See“InitialTVSetup”onthefollowingpages.
8. YoucannowstartwatchingTVoryoucanperform
additionalsetupandcustomizationthroughtheTV
menus.
Guidelines for Setting Up and Using Your New Widescreen TV
TV Operation
1. Reviewchapter4,“TVOperationandFeatures,”for
TVfeaturesincluding:
• Input Selection (viewing source).Selecta
connectedprogramsourcetowatch,suchasa
VCR,DVDplayer,orantenna.Press INPUT onthe
remotecontroltoselectfromiconsfortheTV
inputs.See“ChoosingaViewingSource.”
• ChannelView.Press GUIDE toseechannellist-
ingsforprogramson ANT 1 and ANT 2 .
• Picture Formats.Press FORMAT tocyclethrough
picturesizesandshapestofindtheonebest
suitedtothecurrentprogram.See“TVSignals
andDisplayFormats.”
2. TounderstanduseoftheInput Selectionmenu
withNetCommand-controlleddevices,see“Using
NetCommand”(Yand734seriesmodels).
3. ToviewJPEGphotofilesontheTV,see“Viewing
JPEGPictureFiles.”
Additional TV Setup
1. Reviewchapter5,“TVMenuSettings,”tocustom-
izeTVoperation.Pressthe MENU keytoenterthe
menusystem.Someexamplesofsettingsyoumay
wishtochangeinclude:
• FAV.Useanon-screenmenutocreatecustom
listsofyourfavoritechannels.SeeSetup >
Edit.
• Order.RearrangethedeviceiconsintheInput
Selectionmenutoputfrequentlyusedicons
nearthefront.SeetheInputsmenuOrder
options.
• Name.Changethedevicenamesthatappear
intheInput Selectionmenu.SeetheInputs
menuNameoptions.
• Parental Locks.RestrictTVviewingby
programrating,bychannel,orbytimeofday.
Youcanalsodisablethefront-panelbuttons
ifyouhavesmallchildren.SeetheLock >
2

12 2. TV Setup
Parentmenu,theLock > Front Panelmenu,
andSetup > Edit > Lock.
• Video Settings.Changevideoadjustmentsto
getthebestpictureforyourviewingconditions.
See“AVMenu.”
Note: YoumaywishtochangethePictureModefrom
thedefaultBrillianttoeitherBrightorNatural,
whicharesuitableformosthomeviewingenvi-
ronments.
2. ToprogramtheremotecontroltooperateA/V
devicesnotunderNetCommandcontrol,see
AppendixD,“ProgrammingtheRemoteControl.”
TV Care
• Lamp Cartridge.Whenthelampcartridge
needsreplacement,replace the lamp yourself
and save the cost of a service call.See
Appendix Cforinstructions.
• General Cleaning.Seethecleaningrecom-
mendationsunder“Important Information
About Your TV.”
Assistance
• Fortroubleshooting,service,andproduct
support,seeAppendix E.
• Forwarrantyinformation,seetheTVwarranty
inthebackofthisbook.
Installing the Remote Control Batteries
1. Removetheremotecontrol’sbackcoverbygently
pressinginthetabandliftingoffthecover.
2. Loadthebatteries,makingsurethepolarities(+)
and(-)arecorrect.Forbestresults,insertthe
negative(-)endfirst.
3. Snapthecoverbackinplace.
2
1
The remote control requires two AA alkaline batteries.
Turning the TV On or Off
ToturntheTVonoroff,pointtheremotecontrol
atthefrontoftheTVandpressthe POWER button.
Alternatively,pressthe POWER buttononthefront
paneloftheTV.
If You Turn Off the TV by Mistake
1. Press POWER againwithinabout30seconds,
whilethelampisstillhot,tohavetheTVcome
backonimmediately.
2. Ifthe LAMP indicatorstartsblinking(about30
secondsafteryoushutoffpower),wait about
one minute for the LAMP indicator to stop
blinking and press POWER to turn the TV on
again.
When You First Power On the TV
Choosing a Language for Menus
1. PowerontheTVforthefirsttime.
2. Press toselecteitherEnglishorSpanish
forallmenus.Youcanlaterchangethelanguage
selectionthroughtheSetupmenuLanguage
option.
When you first power on the TV, the Welcome screen lets
you change the menu language.
Initial TV Setup
UsetheSetupmenuforbasicTVsetupoptions.
1. Press MENU toopentheMainmenu.
2. Press tohighlighttheSetupiconanddisplaythe
Setupmenu.
Setup menu highlighted in TV Main menu

2. TV Setup 13
Change the Menu Language
Choosetodisplayon-screenmenusineitherEnglishor
Spanish(Español).
Select a menu language in the Setup menu.
1. WiththeSetupmenudisplayed,press tohigh-
lighttheLanguageicon.
2. Press tohighlighteitherEnglishorSpanish.
3. Press MENU toreturnthehighlighttothetoprowof
icons.
Memorize Channels
For ANT 1/MAIN and ANT 2/AUX
To start channel memorization
1. WiththeSetupmenudisplayed,press tohigh-
lighttheScanicon.
2. Press tohighlightaninputselectionbasedon
yourconnections:
Input Condition
Ant 1 Air
Ant 2 Air
Whenconnectedtoanindooror
outdoorantenna
Ant 1 Cable
Ant 2 Cable
Whenconnectedtodirectcable(no
cablebox)
3. Press tohighlighttheon-screenSTARTbutton.
4. Press ENTER tostartautomaticchannelmemoriza-
tion.
To stop channel memorization before
completion, press CANCEL .
Start channel memorization from the Setup menu.
Additional TV Setup Using the Setup Menu
Seechapter5,“TVMenuSettings,”to:
• Editchanneloptions
• SettheTVclock
• SettheTVTimer
• SelectanEnergyModetomanagepowerusewhile
theTVisoff.
Initial TV Setup, continued
5. Whenmemorizationiscompleteyoucan:
• Press MENU oncetoreturntothetoprowoficons.
• Press MENU againtoreturntotheMainmenu.
• Press EXIT towatchTV.
Afterchannelshavebeenmemorized:
• Totunetomemorizedchannels,press CH /
whilewatchingTVonthe ANT 1 or ANT 2 inputs.
• UsetheSetup > Editmenuforadditionalchannel
options,suchasaddingordeletingchannelsfrom
memory,namingchannels,andsavingfavorite
channelsincustommemorybanks.
Setting Up TV Inputs
When You First Connect a Device
ThisTV’sEasyConnect®AutoInputSensingfeature
detectsmostconnectionsautomatically.Whenyoufirst
connectadevice,theTVwill:
a. detecttheconnecteddevice
b. promptyoutoidentifythedevicetype
c. promptyoutoperformNetCommandset-upfor
thedevice,ifavailable(Yseriesand734series
only)
d. repeatthesestepsforanyadditionalnewly
detecteddevices
ThetablesbelowclarifywhichconnectionstriggerAuto
InputSensing.
Auto Detection Active No Auto Detection
INPUT 1 , 2 , 3 videojacks ANT 1 and ANT 2
COMPONENT
videojacks
HDMI
*
DIGITAL AUDIO OUT
AVR AUDIO OUTPUT
(analog)
USB (USBphotoportonfront)
*
Ifthedeviceispoweredoffwhenconnected,detec-
tionoccurswhenthedeviceisnextpoweredon.

14 2. TV Setup
Note: Forconnectionandsetupofapersonalcom-
puter,seetheinformationlaterinthischapter.
1. Seechapter3,“TVConnections,”forrecommen-
dationsonconnectingyourdevices.
2. ConnectyourdevicestotheTV,makingnoteof
whichTVinputisusedforeachdevice.
TheTVandthedevicescanbeeitheronoroff
whenconnecting.
First select a
device type.
Next perform
IR “learning.”
Auto Input Sensing screen for most device types. The
Learn icon appears only on models with NetCommand.
3. PowerontheTVifnotalreadyon.WhentheTV
detectsaconnection,theAuto Input Sensing
screenopens.
• MostDeviceTypes:Specifythedevice
typeandthen,ifdesired,proceeddirectlyto
NetCommandsetupifavailable.
a. IntheAuto Input Sensingscreen,press
tomovethroughthedevicelisttoselect
thedevicetypeconnectedtotheinput.
Thedevicetypeyouselectherewillappear
intheInput Selectionmenu.
b. IfNetCommandIR“learning”isavailableon
yourTVmodel,youcanperform“learning”
noworatalatertime.Toperformnow,
highlighttheLearniconandpress ENTER .
Seechapter6,“NetCommand”formore.
• A/V Receiver:TheTVcandetectaudiocon-
nectionsonthe DIGITAL AUDIO OUT jackand
theright(red)analog AVR AUDIO OUTPUT jack.
Note for Analog A/V Receivers:Whenyou
disconnectananalogA/Vreceiver,manually
changetheSpeakerssettingtoTVtohear
soundfromtheTVspeakers.
IfNetCommandIR“learning”isavailableforyour
TVmodel,perform“learning”noworatalater
time.Toperformnow,highlightth eLearnicon
intheAuto Output Sensingscreenandpress
ENTER .Seechapter6,“NetCommand”formore.
• HDMI Devices Compatible with the TV’s
NetCommand for HDMI Feature:Compatible
Setting Up TV Inputs, continued HDMIdevicesareoftenrecognizedautomati-
callybytheTV.TheTV’sremotecontrolmay
operatesomedevicefunctionswithoutfurther
setup.Youcanaddmorecontrolfunctionsif
desired.ProgramtheTV’sremotecontrolor,
inthecaseofaYor734seriesTV,perform
NetCommandIR“learning”toaddfunctions.
4 Press EXIT toclosetheAuto Input Sensingscreen.
TheTVwillthendisplaytheAuto Input Sensing
screenforthenextconnectionitfinds.
More About Auto Input Sensing
• Chooseadifferentnameforeachinput.
• Antennainputs( ANT 1/ANT 2 )areneverdetected,
althoughyoucanturnoffunusedantennainputsin
theInputs > Namemenu.
• Youcanchangethedevicetypeatalatertime
usingtheInputs > Namemenu.Any“learned”
NetCommandIRcodeswillbeerased,however.
• IfyouwishtochangedevicesonanHDMIinput:
1. DisconnecttheHDMIdevice.
2. TurnofftheHDMIinputintheInputs > Name
menu.
3. ConnectthenewdeviceandtheAuto Input
Sensingscreenwilldisplay.Ifyouwantthe
deviceunderNetCommandIRcontrol,perform
NetCommand“learning”forthenewdevice.
Controlling A/V Receiver Sound Volume
AlthoughtheTVdetectswhenyouconnectanA/V
receiver,youmustuseoneofthemethodsbelowto
controlsoundvolumefromtheA/Vreceiver.
With a Standard TV Setup
• RecommendedMethod:ProgramtheTV’sremote
controlforyourA/VreceiverandenabletheAudio
Lockfeature.SeeAppendixD,“Programmingthe
RemoteControl.”
• ProgramtheTV’sremotecontrolforyourA/V
receiverandsettheTVremote’sslideswitchto
the AUDIO positiontocontrolvolume.Settheswitch
backtothe TV positiontocontroltheTV.
• UsetheremotecontrolthatcamewiththeA/V
receiver.
With NetCommand Control of an A/V Receiver (Y
and 734 series only)
• SetupNetCommandcontroloftheA/Vreceiver’s
volumefunctionsintheInputs > AVRmenu.The
TV’sremotewillthenautomaticallycontrolA/V
receivervolume.Seechapter6,“NetCommand.”
• Useanyofthemethodsdescribedforthestandard
TVsetup.

2. TV Setup 15
Connecting a Computer to the TV
Useoneoftheconnectionmethodslistedbelowbased
onyourcomputer’svideooutput.
Computer
Video Output
Video Connection Audio
Connection
Digital DVI DVI-to-HDMIcable
oranHDMIcable
withanHDMI-to-
DVIadapter
Stereoaudio
cables
Note: Ifthecomputer’saudiooutput
isasingleminijack,aminiaudio-to-
RCA-male“Y”adaptercableisalso
required.
HDMI HDMI-to-HDMI
cable
Noadditional
audioconnec-
tionisrequired.
IMPORTANT
This TV accepts digital computer signals only.
1. SeetheTVspecificationsinAppendixAtoconfirm
thatyourcomputersignaliscompatiblewiththeTV.
2. Connectthecomputer’sdigitalsignaloutputtoone
oftheTV’s HDMI jacks.Seetheconnectiondia-
gramsforthemethodsuitedtoyourequipment.
3. Connectthecomputer’saudiooutputusingoneof
theseoptions:
• FordigitalDVIsignals,connectanalogleft/right
audiototheTV’s PC/DVI AUDIO INPUT jack.
• ForHDMIsignals,noadditionalaudioconnec-
tionisrequired.
4. PowerontheTVandcomputer.TheTVwilldetect
theconnectionanddisplaytheAuto Input Sensing
screen.
5. IntheAuto Input Sensingscreen,press to
highlightPCinthelistofdevicetypes.Youcan
changethetypeatalatertimeusingtheInputs >
Namemenu.
6. Press EXIT toclosetheAuto Input Sensingscreen.
)%.*UP%7*$BCMF




INPUT 1
INPUT 2
L
( MONO) R
AUDIO
ANT 2/ AUX
ANT 1 / MAIN
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA/ SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
COMPONENT 1
COMPONENT 2
PC/DVI
AUDIO
INPUT
4UFSFP"VEJP$BCMF
A DVI connection from a personal computer requires a
separate audio connection.
1FSTPOBM
$PNQVUFSXJUI
)%.*0VUQVU
INPUT 1
INPUT 2
L(MONO) R
AUDIO
ANT 2/ AUX
ANT 1 / MAIN
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA/ 720p /1080p
IR EMITTER
NetCommand R
PC/DVI
AUDIO
INPUT
COMPONENT 1
COMPONENT 2
)%.*UP)%.*$BCMF 
 57#BDL1BOFM
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
Note: Ifyourcomputerprovidesdigitalaudio
output(coaxialordigital),youcanconnectit
directlytoadigitalA/Vreceiverandbypass
theTV.
Using the TV with a Personal Computer

16 2. TV Setup
Tip:
Setthecomputer’sscreensavertodisplayapattern
afterseveralminutesofinactivity.Thisactsasa
reminderthattheTVispoweredonandthelamp
isinuse.ThelampisinusewhenevertheTVis
poweredon,evenifthescreenappearsdark.
Computer Video Adjustments
1. Poweronthecomputerifitisnotalreadyon.
2. SelectPCfromtheInput Selectionmenu.Todo
this,press INPUT toopentheInput Selectionmenu,
movethehighlighttothePCicon,andpress ENTER.
3. Workingfromthecomputer,changetheresolution
ofthecomputerimage.Viewthecomputerimage
ontheTVandmaximizethecomputerresolution
whilemaintainingasuitableaspectratioforthe
image.
4. PerformTVvideoadjustments.Press
VIDEO repeatedlytoaccessvideo-
adjustmentoptions.Thefollowing
additionaladjustmentsareavailable
forcomputervideo:
Horiz Position(HorizontalPosition).
Manuallyadjustthehorizontal
position.
Vert Position(VerticalPosition).
Manuallyadjusttheverticalposition.
5. Press FORMAT repeatedlytofindthe
pictureformatbestsuitedtothe
image.Seethechartonthispage
showinghowdifferentcomputerreso-
lutionsaredisplayedontheTV.
Image Resolution
YourMitsubishiTVcandisplayresolutions
fromstandardVGA(640x480)through
1920x1080signalsatarefreshrateof60
Hz.Theresolutionof1920x1080issup-
portedatrefreshratesof24,30,and60
Hz.SeeAppendixAinthisbookformore
oncompatiblescreenresolutions.
Inmostcases,thecomputerwillselectthe
bestresolutionmatchtodisplayontheTV.
Youcanoverridethissettingifyouwish.
Refertoyourcomputeroperatingsystem’s
instructionsforinformationonchanging
thescreenresolution.
Youmayneedtorestartthecomputerfor
changestotakeeffect.
Using the TV with a Personal Computer
Computer Display Formats
Pressthe FORMAT keyrepeatedlytocyclethroughtheTVdisplays
availableforyourcomputer’svideosignal.
Computer Signal As Displayed on TV Screen
Format 4 X 3
Standard
16 X 9
Standard Zoom
VGA
640 X 480
WVGA
848 X 480
SVGA
800 X 600
WSVGA
1064 X 600
Format Standard Zoom
XGA
1024 X 768
PC 720p
1280 X 720
WXGA
1360 X 768
SXGA
1280 X 1024
Format Standard Reduce
PC 1080p
1920 X 1080
Distortion in Computer Images
Computerimagesmayshowdistortion
whenviewedontheTV,e.g.,linesthat
shouldbestraightmayappearslightly
curved.

17
3TV Connections
INPUT 1
INPUT 2
L
( MONO) R
AUDIO
ANT 2/ AUX
ANT 1 / MAIN
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
AUDIO
YPb Pr L
( MONO) R
Y Pb Pr (480i/480p/720p/1080i)
-
"6%*0
3
: 1C 1S





$"#-&*/PS
4"5&--*5&*/
*ODPNJOHGSPN
$BCMF4FSWJDFPS
4BUFMMJUF%JTI
57
$BCMF#PY
PS4BUFMMJUF
3FDFJWFS
Figure 1. Connecting an external HDTV receiver with
component video connections
Auto Input Sensing
TheTV’sAutoInputSensingfeatureautomaticallyrec-
ognizesmostconnectionsandpromptsyoutoidentify
thetypeofdeviceconnected.Seechapter2,“TV
Setup,”formoreonAutoInputSensing.
Connection Types
Reviewtheconnectiontypesavailableonyourinput
devicesanduseinputsthatwillgivethebestvideo
quality.Forexample,chooseHDMIovercomponent
video,andchoosecomponentvideooverS-videoor
compositevideo.
Picture Quality
Forbestpicturequality,routesignalsdirectlyfrom
theinputdevicetotheTV;avoidroutingvideosignals
throughanA/Vreceiver,forexample.
IfyourcableboxorsatellitereceiverhasanHDMI
output,usetheconnectionsforHDMIdevices
describedlaterinthischapter.
Required:RCAcomponentvideocables,left/right
analogstereoaudiocables.
1. Connectthecablefromtheoutsidecableorsatel-
liteserviceto CABLE IN or SATELLITE IN onthe
cableboxorsatellitereceiver.Seeyourdevice’s
owner’sguideforinstructionsandcablecompatibil-
ity.
2. ConnectRCA-typecablesfromthe Y PB PR outputs
ontheHDTVcableboxorsatellitereceiverto
COMPONENT ontheTVbackpanel,matchingthe
coloredgreen,blue,andredconnections.
3. Connectleft(white)andright(red)audiocables
fromtheHDTVcableboxorsatellitereceiverto
COMPONENT AUDIO L (MONO) and R ontheTV
backpanel.
Note: Toheardigitalsurroundsound,connectthedigital
audiooutputfromyourcableboxorsatellitere-
ceiverdirectlytoyourdigitalA/Vreceiver.
Sound Quality
Forbestaudioquality,routeaudiosignalsfromthe
inputdevicedirectlytoyourA/Vreceiverorsound
systemwheneverpossible.
IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV.
These items are available at many electronics
stores.
Before you Begin
HDTV Cable Box or Satellite Receiver with Component Video

18 3. TV Connections
H DMI Device (Cable Box, Satellite
Receiver, DVD Player, or Other Device
)
Required:HDMI-to-HDMIcable.
ConnectanHDMIcablefromtheTVbackpaneltothe
HDMIdeviceoutput.HDMIdevicesprovidevideoand
audiothroughthesinglecable.
Mitsubishirecommendsyouusecategory2HDMI
cablestoconnectHDMI1.3sourcedevices.High-
speedcategory2cablesbringyouthefullbenefitsof
DeepColorandx.v.Color.Seechapter1,“TVOver-
view,”formoreonHDMIcabletypes.
INPUT 1
INPUT 2
L
( MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
)%.*%FWJDF
57#BDL1BOFM
Figure 3. Connecting an HDMI device.
Note:
HDMIinputsare certiedforproper
interoperabilitywithotherproductscertiedby
Simplay™.
IMPORTANT
HDMI and Audio Signals
• DigitalSurroundSound:TheTV’sHDMI
inputs can receive digital stereo audio
signals only. To hear digital surround
sound from an HDMI device, connect the
device’s digital audio output directly to your
A/V receiver. See the Owner’s Guides for
those devices for instructions.
• A/VReceiverwithHDMI.IfyourA/V
receiver has an HDMI input, use the audio
connections described in “A/V Receiver
(Sound System)” instead.
Standard Cable Box, Satellite Receiver,
or Other Device with S-Video
Required:S-Videocableandleft/rightanalogstereo
audiocables.
1. Connectthecablefromtheoutsidecableorsatel-
liteserviceto CABLE IN or SATELLITE IN onthe
cableboxorsatellitereceiver.
2. ConnectanS-Videocablefrom S-VIDEO OUT on
thecableboxorsatellitereceiverbackpanelto
INPUT S-VIDEO ontheTVbackpanel.
3. Connectleft(white)andright(red)audiocables
from AUDIO OUT onthecableboxorsatellite
receiverto INPUT AUDIO L (MONO) and R ontheTV
backpanel.
Note: Refertothecableboxorsatellitereceiver
Owner’sGuideforcableordishantennacon-
nectionstothereceiver.
"6%*0065
7*%&0065
INPUT 1
INPUT 2
L
( MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA/ SVGA / W-SVGA /
XGA / W-XGA / SXGA/ 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
INPUT 2
$"#-&*/PS
4"5&--*5&*/


"OZ47JEFP%FWJDF
57#BDL1BOFM
*ODPNJOH
$BCMFGSPN
8BMM



Figure 2. Connecting a device with S-Video

3. TV Connections 19
Wall Outlet Cable (no cable box)
Itisveryimportanttoconnecttheincomingcablefor
yourprimaryviewingsourceto ANT 1/MAIN .
1. Connecttheprimaryincomingcoaxialleadcableto
ANT 1/MAIN ontheTVbackpanel.
2. Foranoptionalsecondaryantennasource,connect
anantenna(orcable)to ANT 2/AUX .
INPUT 1
INPUT 2
L
( MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
ANT 2 / AUX
ANT 1 / MAIN
Figure 4. Wall Outlet Cable
Antenna with a Single Lead
A. For an antenna with flat twin leads
Required:300-ohm-to-75-ohmtransformer.
A1. Foranantennawithflattwinleads,connectthe
300-ohmtwinleadstothe300-ohm-to-75-ohm
transformer.
A2.Pushthe75-ohmsideofthetransformeronto ANT 1
ontheTVbackpanel.
B. For cable or antenna with coaxial lead
Connectthecoaxialleaddirectlyto ANT 1 onthe
TVbackpanel.
Antennas with Separate UHF and
VHF Leads
Required:UHF/VHFcombiner
1. ConnecttheUHFandVHFantennaleadstothe
UHF/VHFcombiner.
2. Pushthecombineronto ANT 1/MAIN ontheTV
backpanel.
INPUT 1
INPUT 2
L(MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA/ 720p /1080p
IR EMITTER
NetCommand R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
ANT 1 / MAIN
#BDL
7JFX 4JEF
7JFX
6)'"OUFOOB
$IBOOFMT
7)'"OUFOOB
$IBOOFMT
0INUP
0IN
$PNCJOFS
'MBU5XJO-FBE
6)'
7)'


5P"/5."*/
57
CBDL
QBOFM
&YUFSOBM
"OUFOOB
PS$BCMF
Figure 5. Connecting separate UHF and VHF Antennas
INPUT 1
INPUT 2
L(MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AV R
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 48 0i /480p /720 p /1080i /1080p
AUDIO: PC M STEREO
PC: V GA / W-VGA / S VGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
ANT 1 / MAIN
0IN
'MBU5XJO
-FBE
0QUJPOBM0IN
UP0IN
.BUDIJOH5SBOTGPSNFS
0IN
$PBYJBM
$BCMF
#
"
"
57
#BDL
1BOFM
Figure 6. Connecting a Single Antenna Lead
Mitsubishi strongly recommends you avoid using
antennas with flat twin leads. Flat twin lead
antenna wires are subject to interference which
may adversely affect the performance of the TV.
We recommend using coaxial antenna cable.

20 3. TV Connections
DVI Video Device (Cable Box, Satellite
Receiver, DVD Player, or Other Device)
ConnectDVIdevices(digitalonly)totheTV’sHDMI
inputjacks.
AnalogstereoaudiocablesandaDVI-to-HDMIcableor
DVI/HDMIadapterandHDMIcablearerequired.
1. ConnecttheDVI-to-HDMIcable(recommended)or
HDMIcablewithDVI/HDMIadapterfromtheDVI
device’sbackpaneltotheTV’sHDMIjack.
Note: IfyouareusingaDVI/HDMIadapter,itisimpor-
tanttoconnecttheadaptertotheDVIdevicefor
bestperformance.
2. Connectasetofaudiocablesfrom AUDIO OUT
ontheDVIdevicebackpaneltothe PC/DVI AUDIO
INPUT ontheTVbackpanel.Connectthered
cabletothe R jackandthewhitecabletothe L
(MONO)
jack.
Note: TheHDMIconnectionsupportscopyprotection
(HDCP).
Somedevicesrequireconnectingtoananalog
inputrst,inordertoviewon-screenmenus
andtoselectDVIastheouput.Pleasereview
yourequipmentinstructionsforDVIconnectivity
andcompatibility.
3
-
"6%*0065
%7*065
INPUT 1
INPUT 2
L(MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA/ SVGA / W-SVGA /
XGA / W-XGA / SXGA/ 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
%7*UP)%.*
$BCMF
%7*%FWJDF


57#BDL1BOFM
Figure 8. Connecting a digital DVI device
DVD Player with Component Video
Componentvideocablesandanalogaudiocablesare
required.
1. Connectthecomponentvideocablesfrom Y Pb Pr
VIDEO OUT onthebackoftheDVDplayertothe
COMPONENT jacksontheTVbackpanel,match-
ingthegreen,blue,andredcoloredconnections.
2. Connectleft(white)andright(red)stereoaudio
cablesfrom AUDIO OUT onthebackoftheDVD
playerto COMPONENT AUDIO L (MONO) and
AUDIO R ontheTVbackpanel.
$0.10/&/57*%&0 "6%*0065
- 3
INPUT 1
INPUT 2
L
(MONO) R
AUDIO
DIGITAL
AUDIO
OUT HDMI 12
YPb Pr
:1C 1S
AVR
AUDIO
OUTPUT
S-VIDEO VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
L (MONO) R
YPb Pr
%7%1MBZFS
Figure 7. Connecting a DVD player with component
video
IMPORTANT
See Appendix A for component video signal
compatibility information.
For digital audio connections to your A/V
receiver, see your DVD player and A/V receiver
Owner’s Guides.