Mitsubishi Electric 2107e User manual

:
1
Chapter 1
Unpacking the Package
Check following items. If they are missing or damaged, consult your place of purchase
immediately.
2107e color monitor Users manual
Power cord 15-pin D-SUB Macintosh adapter
signal cable
? Locate the model name and the serial number labeled on the back
of your monitor. Write down the related information of your
monitor and dealer in the space on page iii for future reference.
Unpacking the Package
All manuals and user guides at all-guides.com
all-guides.com

:
2
Features
Super-fine Dot Pitch With 0.25mm super-fine dot pitch and anti-static
coating, 2107e color monitors offer strikingly sharp
and high resolution image up to 1600 x 1200.
Wide Range AutoScan Horizontal frequency ranges from 30KHz to 107
KHz to support 1600 x 1200 @ 90Hz resolution.
Flicker-Free design for vertical frequency of up to
160Hz.
Auto key Pressing the Auto key, the monitor will
automatically adjust displays size and position
to the optimum. No re-configuration or
adjustment is needed when a user changes
display mode.
Low radiation 2107e meets strictest low radiation regulations of
MPRII.
Users and Environment 2107e is produced by the ISO 14001 certified
manufacturer, and in compliance with the global
environmental labelling scheme- MPRII.
Plug’n Play Compatibility Supporting VESA DDC I and DDC 2B
standards, 2107e is compatible with Plugn
Play feature of Window®95 and Window 98®
Chapter 1
All manuals and user guides at all-guides.com

:
3
Power Management
The Power management of this monitor complies with these VESA power
saving modes:
Mode Power Horizontal Vertical LED
Consumption Syne Sync
On Normal On On Green
Stand-by < 15 W Off On Amber
Suspend < 15 W On Off Amber
Off < 5 W Off Off Amber Blinking
Overide Normal Off Off Green
Factory Preset Timings
Resolution Vertical Frequency Horizontal Frequency
(Hz) (KHz)
640 x 400 70 31.47
640 x 480 60 31.47
640 x 480 75 37.50
800 x 600 75 46.88
1024 x 768 75 60.02
1024 x 768 85 68.68
1280 x 1024 75 79.98
1280 x 1024 85 91.15
1600 x 1200 75 93.75
1600 x 1200 85 106
** All above timings are non-Interlace timings.
Unpacking the Package
All manuals and user guides at all-guides.com

:
4
Chapter 2
Chapter 2
Installing the Monitor
This monitor is equipped with an autosensing universal compatible power supply for
voltage ranges 100-120/200-240V AC, 50~60Hz.. Please confirm the line voltage
designation at the rear panel of the monitor before connecting the machine.
1) Make sure that the system power is turned off.
2) Please refer to the instructions below to connect the signal cable through D-SUB or
BNC.
3) Connect the power cord to the monitor and attach it to power source.
4) Turn on the computer and the monitor.
All manuals and user guides at all-guides.com

:
5
Connecting the Signal Cable
Your 2107e provides both D-SUB and BNC signal connectors. The D-SUB or BNC
signals can automatically be detected by its microprocessor.
✏Connecting through D-SUB signal connector
1) Make sure that the system power is turned off.
2) Connect the computer end of the D-SUB cable to the 15-pin output connector on
the video board of your computer.
3)Connect the monitor end of the D-SUB cable to the D-SUB receptacle on the back
of the monitor.
Installingthe Monitor
All manuals and user guides at all-guides.com

:
6
Chapter 2
✏Connecting to An Apple
If you connect the monitor to an Apple Macintosh through a D-Sub cable, you need to
add the Macintosh adapter to connect the video signal port of your computer and the
monitor signal cable. Before connecting the adapter please refer to the user's guide of the
adapter to set the switches of the adapter.
All manuals and user guides at all-guides.com
all-guides.com

:
7
Installingthe Monitor
✏Connecting through BNC Signal Connector
1) Make sure that the system power is turned off.
2) Connect the computer end of the BNC cable to the output connector on the video
board of your computer.
3) Connect the monitor end of the BNC cable to the BNC receptacle on the back of
the monitor.
All manuals and user guides at all-guides.com

:
8
Chapter 3
lMenu key : enters or changes Main menus. There are three main menus.
lEnter key : enters sub-menus or selects items.
lExit key : goes back to main menus (auto save), or leaves OSD.
l
& key :scrolls the light coloured bar up or down and represents
HOT KEY for brightness adjustment.
l&key : scrolls the light coloured bar left or right and represents
HOT KEY for contrast adjustment.
lAuto key : is used for Fuzzy Automatic calibration adjustment.
Chapter 3
A Look at the Control Panel
Auto
Exit Enter
Menu
Auto key
Exit Enter
Menu
All manuals and user guides at all-guides.com

:
9
Making Adjustments
Auto key(Fuzzy Auto Calibration )
Just push the Auto key, then the monitor will automatically adjust display's size and
position to the optimum. No re-configuration or adjustment is needed when a user
changes display mode.
The Auto key function is different from "Reset" function. "Reset" function for display's
geometry, size and position only works under the factory preset timings (please see
page 3). The Auto key function will work under "ANY" display timings which 2107e can
support.
Hot Keys
Press or key to adjust contrast directly.
Press or key to adjust brightness directly.
A Look at the Control Panel
All manuals and user guides at all-guides.com

:
10
Chapter 3
OSD Operation
1) Press Menu key to enter or change Main menus (there are three main menus)
2) Press or keys to scroll light coloured bar to desired items.
3) Press Enter key to enter sub-menus.
4) Press ,(,) key to do the adjustments. If the sub-menu contains
multiple items. Press or keys to scroll light coloured bar to desired items.
Then press or key to adjust as required.
5) Press Exit key to save and return to main menus.
6) Press Exit key to save and leave OSD
? Reset to the factory default settings, please see General Settings
Reset and Color Temperature Reset.
Main Menu 1 Display Control
This main menu includes six items. Scroll the light coloured bar to desired items and
press Enter to sub-menus.
All manuals and user guides at all-guides.com

:
11
Contrast adjusts the difference between the light and dark areas.
Brightness adjusts the brightness of the display.
Size & Position
Display size and position adjustment
Luminance
Contrast and Brightness adjustments
A Look at the Control Panel
All manuals and user guides at all-guides.com
all-guides.com

:
12
Chapter 3
Hor. Position adjusts the horizontal position of the display.
Hor. Size adjusts the width of the display.
Ver. Position adjusts the vertical position of the display.
Ver. Size adjusts the vertical height of the display.
Geometry
Advanced geometry adjustments
Pincushion controls the straightness of the vertical edges of the display.
Unbalance adjusts balance when the sides of display are bowed
towards left or right
Trapezoid makes the vertical edges of the display parallel.
Parallelogram corrects image leaning left or right.
Rotation corrects screen tilt.
Top Corner adjusts the edges on the top corners of the screen image.
Bottom Corner adjusts the edges on the bottom corners of the screen
image.
All manuals and user guides at all-guides.com

:
13
OSD Position
OSD position adjustments
adjusts the OSD menu position up.
adjusts the OSD menu position down.
adjusts the OSD menu position left.
adjusts the OSD menu position right.
Degauss
Manual Degauss.
To eliminate color shading or impurity induced by magnetism,
press Enter to active Degauss function.
Reset to Default
Reset the monitor to the default factory settings including H/V position, H/V size,
Pincushion, Unbalance, Trapezoid, Parallelogram, Rotation, Corner, H/V Convergence,
H/V Moie and Moire. For preset timings, in order to reset to factory default
values, press Enter. To reset color Temperature, plsease see page 15.
A Look at the Control Panel
All manuals and user guides at all-guides.com

:
14
Chapter 3
Main Menu 2 Color Control
This main menu is defined as color weight adjustment. C1 ~ C5 are color storage
areas, which are factory preset but can also be modified by user. The preset informa-
tion as follows :
Factory Default Color Temperature
C1 9300K
C2 6500K
C3 5500K
C4 7100K
C5 11500K
Scroll the light coloured bar to desired color temperature, then press Exit to save the
setting and leave OSD. Press Enter key to sub-menus and adjust RGB color weight.
All manuals and user guides at all-guides.com

:
15
This sub-menu adjusts RGB (Red, Green, Blue) color weight. Press or keys to scroll
light coloured bar to desired items then press or key to do the adjustments.
? To reset to factory default values, scroll light coloured bar to item
“ Reset to Default”.
Main Menu 3 Advanced Display Control
This main menu includes six items, scroll light coloured bar to desired items. Press Enter
key to enter sub-menus.
A Look at the Control Panel
All manuals and user guides at all-guides.com

:
16
Chapter 3
Convergence
Horizontal & Vertical Convergence adjustment
Hor. Convergence: adjusts Horizontal Convergence
Ver. Convergence:
adjusts Vertical Convergence
Convergence is the monitor's ability to precisely illuminate specific phosphors
and line them up properly in order to produce pure color. Displayed characters and
images may appear fuzzy or have tinges of red , green, or blue if the electron beams do
not converge correctly.
2107e offers a convergence adjustment feature. To properly adjust convergence, it is
best to have an image that makes it easy to see any convergence error. A black
background with white letters or lines is recommended. When adjusting convergence,
look at the adjustment across the whole screen. When adjusting horizontal convergence,
look at the left and right edges of vertical lines or characters. When adjusting vertical
convergence, look at the top and bottom edges of horizontal lines or characters. The
monitor is properly adjusted when the effects of red and blue tinges are minimized.
? The convergence adjustment adjusts the entire screen. It is not
possible to limit adjustment to specific screen areas.
? Factory default setting values : 0
All manuals and user guides at all-guides.com
all-guides.com

:
17
Moire
Horizontal & Vertical Moire adjustment
Horizontal Moire: adjusts horizontal Moire
Vertical Moire: adjusts vertical Moire
Moire refers to an interference pattern of dark wavy lines on the screen. It is an
interference phenomenon caused by the relationship between the phosphor layout
and the imaging signal. In fact, it is often considered an indication of good focus level.
? It is especially noticeable when using a light-gray or every-other-
dot pattern. Moire cannot be eliminated. However, it can be re-
duced with the moire reduction feature.
Moire can be reduced by adjusting the iscreen moire reduction function. Prior to
adjustment, set the screen to a full white pattern so that moire will be visible. After this
adjustment, make changes to a different screen background in order to reduce moire
even further.
? If the picture is unstable when you adjust the moire reduction
setting, over-adjustment has occured. Please lower the moire re-
duction setting level. (Factory default setting value : 0).
A Look at the Control Panel
All manuals and user guides at all-guides.com

:
18
Chapter 3
Language Select
The sub-menu is defined as language selection and there are five languages to
choose from.
D-Sub BNC
Input connector select.
There are two kinds of input connectors for 2107e. One is a BNC connector, the
other is a DB-15. The 2107e is capable of automatically detecting the type of connec-
tor used (either BNC or DB-15). If the two connectors are connected simultaneously,
the user can select the desired connector.
All manuals and user guides at all-guides.com

:
19
Purity
Colour purity adjustment
To adjust Purity, choose a full white picture and adjust to get a pure white
picture at the corner of the screen image.
Display Mode
Current resolution, horizontal and vertical frequency status presentation.
A Look at the Control Panel
All manuals and user guides at all-guides.com

:
20
Chapter 3
By making adjustments to your video card settings, you can set the timing and the
refresh rate according to your preferences. The monitor will automatically save the
settings. Your monitor can accept a vertical frequency ranging from 50 Hz to 160 Hz
and an horizontal frequency from 30 KHz to 107 KHz. However, due to different
video card and resolution settings, we recommend that you do not exceed the maxi-
mum refresh rate, 160 Hz for vertical frequency and 107KHz for horizontal frequency
to avoid possible damage to your monitor.
Resolution Recommended Maximum Vertical
Refresh Rate(Hz)
640 x 480 160
800 x 600 145
1024 x 768 135
1280 x 1024 100
1600 x 1200 90
? To set the timing and the refresh rate, please see the user's guide of
your video card.
Timing Setting
All manuals and user guides at all-guides.com