Mitsubishi Electric PLK-G2008H User manual

INDUSTRIAL SEWING MACHINE
MODEL
PLK-G2008H
TECHNICAL MANUAL SEWING MACHINE HEAD
A180E674P04

FOR SAFE USE
Before the installation, operation, and inspection for this product, read the “FOR SAFE USE” and the
technical manuals carefully. Also read the other technical manuals, “Control Unit” and “Operation Panel”
describing some instructions, which are not in this manual, and use the sewing machine properly.
SAFETY INDICATIONS
DANGER
Indicates that incorrect handling may cause hazardous conditions, resulting
in death or severe injury.
CAUTION
Indicates that incorrect handling may cause hazardous conditions, resulting
in medium or slight personal injury or physical damage. Note that CAUTION
level may lead to a serious consequence according to the circumstances.
Always follow the instructions of both levels because they are important to
personal safety.
CAUTION INDICATIONS
No. Caution indication Description
1
Precaution for sewing machine operation:
Indicates that removing the safety and operating
the sewing
machine for some other purposes with power-on are prohibited.
Please do not operate the sewing machine without
protective equipment such as an eye guard, a belt cover or
the others.
Please turn off the power switch when threading, changing
a needle and a bobbin, cleaning, and lubricating.
2
Caution for fingers injury:
Indicates a possibility of fingers (hands) injury in a certain
condition.
3
Caution for squeezing fingers:
Indicates a possibility of squeezing fingers in a certain condition.
4
Indication of pulley rotation direction:
Indicates a normal pulley rotation direction of sewing machine.

SAFETY PRECAUTIONS
DANGER
To prevent from receiving an electric shock, always turn off a power switch and unplug power supply
when opening a control box, and then open after ten minutes passes.
CAUTION
USAGE ENVIRONMENT
Please do not operate the sewing machine under the following conditions.
(1) In the ambient temperature of 35 degrees (95°F) or more than 35 degrees, or the ambient
temperature of 5 degrees or less than 5 degrees (41°F).
(2) In the ambient temperature of 55 degrees (131°F) or more than 55 degrees, or the ambient
temperature of -10 degrees or less than -10 degrees (18°F) during transportation.
(3) In the relative humidity exceeding 85% or less than 45%.
(4) In the open-air place or the location that receives direct sunlight.
(5) In the place near heat sources such as heating devices.
(6) In the atmosphere filled with dust, explosive gas, or corrosive gas.
(7) In the place where the fluctuation in the power voltage of 10% or more than 10%, or the power
voltage of -10% or less than -10% of the fixed power voltage.
(8) In the place where the power source cannot supply enough voltage to keep the motor running.
(9) In the place filled with strong electric noises such as high-frequency welders.
INSTALLATION
(1)
Please have some specialists, who have enough experience for the sewing machine installations,
install the sewing machine.
(2) Please have a qualified electrician perform necessary electric wiring.
(3) Please do not operate until the sewing machine is repaired when any damage or fault is found on
the sewing machine at the installation.
(4) Please do not refurbish the sewing machine.
(5)
The sewing machine is heavy. For the safety, please make sure to install the sewing machine head
by more than one person.
(6) When tilti
ng the sewing machine, please stand at the hinge side and hold the sewing machine with
both hands.Also, please lock the caster on the steel stand
(7) When tilting the sewing machine, the work clamp slides toward the hinges. Remember to move the
work clamps Fu
lly to the right side of the casting before placing the sewing head in the sewing
position.
(8)
Please lock the caster on the steel stand to prevent the machine from moving before tilting the
sewing machine.

(9) Please make sure to fit the safety protective
equipment (the motor cover or the others) and the
accessory protective equipment (the eye guard) that removed temporarily for installation.
(10) If the table and the steel stand are not MITSUBISHI original, the table and the steel stand have to
be strong enough to withstand the weight and vibration of the sewing machine.
(11) When fitting the caster to the steel stand that are not MITSUBISHI original, the caster with locking
function has to be strong enough to withstand the weight and vibration of the sewing machine.
SEWING
(1) Please make sure to turn the power switch off before installing or replacing needles.
(2) Please pay attention for the fingers not to be injured by the needle point.
(3) Please make sure to turn power switch off before lubricating.
(4) Please pay attention that oil does not get on your skin or in your eyes as it
may cause an
inflammation.
(5) Please make sure to keep oil out of the reach of children who may drink oil by mistake.
(6) Please make sure to turn the power switch off before threading a needle.
(7) Before starting the sewing, please make sure the position and the function of the halt switch.
(8) Please do not touch the operating parts during sewing operation.
(9)
It is very dangerous to operate the sewing machine without safety guards (eye guards, belt covers,
link covers, finger guards or the others).
Please make sure to operate the sewing machine with safety guards.
(10) Please make sure to turn the power switch off when stopping the sewing machine temporarily.
(11) Please do not operate the foot switch during sewing.
ADJUSTMENT
(1) Please make sure to turn the power switch off before adjusting the sewing machine.
(2) If the adjustment is required while the power switch on, do not step on the foot switch by mistake.
(3) Please be careful not to be injured by a sharp part such as the needle and the shuttle hook point.
(4) Please make sure to put the safety guards (eye guards, belt guards, link covers, or the others) back
on the initial position after the sewing machine adjustment.
(5) Please make sure to lock the caster on the table when tilting the sewing machine.

CONTENTS
1. STRUCTURE OF THE SEWING MACHINE···································· 1
2. SPECIFICATION······································································· 2
3. INSTALLATION········································································ 3
3-1. Preparation of the table
··········································································
3-2. Preparation of the steel stand··································································
3-3. Installation of the motor··········································································
3-4. Installation of the control box···································································
3-5. Connection of the operation panel····························································
3-6. Installation of the power switch································································
3-7. Connection of the foot switch···································································
3-8. Installation of the oil pan·········································································
3-9. Installation of the sewing machine head·····················································
3-10. Installation of the V-belt········································································
3-11. Connection of the electric cables····························································
3-12. Installation of the belt cover···································································
3-13. Installation of the thread stand·······························································
3-14. Connection of the air tube ····································································
3
3
3
3
3
4
4
5
5
6
6
8
8
9
4. LUBRICATION········································································· 10
5. PROPER OPERATION······························································ 11
5-1. Initial setting of the control box
·································································
5-2. Initial setting of the setting table·······························································
5-2-1. Reading of the setting table ·······························································
5-2-2. How to create a USB memory for initial configuration ······························
5-3. Installation of the needle·········································································
5-4. Threading the upper thread·····································································
5-5. Winding the bobbin thread······································································
5-6. Setting the bobbin·················································································
5-6-1. Taking out the bobbin········································································
5-6-2. Setting the bobbin·············································································
11
11
11
13
15
16
17
18
18
18

6. SEWING················································································· 19
6-1. The sewing operation
············································································
6-2. Operation of the halt switch·····································································
6-3. The teaching operation··········································································
6-4. Pre-heating control················································································
6-5. Setting of the Left / right alternating clamp specification·································
6-5-1. Setting of the clamp priority order·························································
6-5-2. Setting of the method of the clamp up for the step clamp movement············
6-5-3. Setting of the input signal for the input / output setting mode······················
6-6. The thermal trimming operation·······························································
6-6-1. Manual / Test mode conversion switch <1>············································
6-6-2. Thermal thread trimming device switch <2>············································
6-7. Adjustment of the thread tension······························································
6-7-1. Bobbin thread tension········································································
6-7-2. Upper thread tension·········································································
19
19
20
21
21
21
22
22
23
23
23
24
24
24
7. STANDARD ADJUSTMENT························································ 25
7-1. Adjustment of the shuttle········································································
7-2. Adjustment of the position between the needle and the shuttle hook················
7-3. Adjustment of the needle bar height ·························································
7-4. Adjustment of the needle to shuttle clearance·············································
7-5. Adjustment of the needle to driver clearance···············································
7-6. Test mode operation··············································································
7-6-1. Entrance for the test mode operation····················································
7-6-2. Key function in the test mode······························································
7-6-3. Checking method of the input signal in the sewing state···························
7-6-4. Countermeasure for troubles······························································
7-7. Adjustment of the presser foot·································································
7-7-1. Adjustment of the driving shaft arm(front) and the presser foot····················
7-7-2. Adjustment of the sensor of the presser foot cylinder································
7-8. Adjustment of the tension release·····························································
7-9. Upper thread thermal trimming device·······················································
7-9-1. Setting thread puller··········································································
7-9-2. Setting of the thickness detector··························································
7-9-3. Setting of the thread wiper··································································
7-9-4. Adjustment of the upper thread heater···················································
7-10. Adjustment of lower thread trimmer heater················································
7-11. Adjustment of the bobbin winder·····························································
7-12. Adjustment of the work holder pressure ···················································
7-13. Adjustment of the Thread take up spring tension········································
25
25
26
27
27
28
28
29
31
32
33
33
34
34
35
35
36
36
37
38
39
39
40

7-14. Adjustment of the position detecting disc··················································
7-15. The relation of the hook position and upper stop position·····························
7-16. Adjustment of the mechanical home position·············································
7-16-1. Adjustment of the X direction····························································
7-16-2.Adjustment of the Y direction····························································
7-17. Adjustment of the X-Y drive timing belt tension··········································
7-17-1.Adjustment of the X timing belt tension···············································
7-17-2. Adjustment of the Y timing belt tension···············································
40
41
41
42
43
44
44
45
8. MAINTENANCE······································································· 46
8-1. Cleaning
·····························································································
8-2. Disposing of oil waste············································································ 46
46
9. TROUBLESHOOTING······························································· 47

1. STRUCTURE OF THE SEWING MACHINE
PLK-G2008H electronic pattern sewing machine consists of the following main parts.
<1>: Sewing machine head <2>: Main motor <3>: Halt switch <4>: Control box
<5>: Operation panel <6>: Work holder foot switch <7>: Start foot switch <8>: Steel stand
<9>: Thread stand <10>: Power switch <11>:Air regulator
<1>
<2>
<3>
<4>
<5>
<6>
<7>
<8>
<9>
<10>
<11>
- 1 -

2. SPECIFICATIONS
Model : PLK-G2008H
Sewing area : X-direction (left/right) 200 mm, Y-direction (front / back) 80 mm
Maximum sewing speed : 700 rpm
Setting speed : 10 speed levels in 200 rpm to 700 rpm
Stitch length : 0.1 to 20.0 mm
Stitch type : Single needle lock stitch
Maximum number of needles : 20,000 per pattern
Storable sewing data item : 900 patterns (internal memory)
Data memory : Internal memory, USB memory
Needle bar stroke : 56.3 mm
Thread take up lever stroke : 94 mm
Class of needle : Schmitz 794 #230
Presser foot lift *1 : 25 mm
Work holder lift : 20 mm (25 mm max)
Hook :
Barrel shuttle hook
Bobbin : Large size bobbin
Thread trimmer system : Thermal trimming system
Voltage IN :AC 210/230 V OUT : AC 1V
Pre heating : Available by using Function Code 4
Thread : #8 to #00 (Synthetic)
Lubrication system : Manual oiling
Lubrication oil : Pulley SF oil
X-Y drive system : Stepping motor feedback control
Timing belt drive system Intermittent or continuous feeding
*2
Machine dimensions : 1,200 mm (W) ×780 mm (L) ×1,320 mm (H)
Total mass : 172 Kg
Type of motor : XL-G554-20(Y)
Type of controller : PLK-G-CU-20M
Type of operation panel : PLK-G-PAL
Power : In 200V to 240V single-phrase or three-phrase
The power in 110V to 120V or in 380V to 415V is compatible with
power unit (option).
*1：Presser foot lift is the height of the presser foot after the sewing has stopped.
*2：Recommend intermittent feeding.
- 2 -

3. INSTALLATION
CAUTION
(1)
Please have some specialists, who have enough experience for the sewing machine installations,
install the sewing machine.
(2) Please have a Qualified Electrician perform necessary electric wiring.
(3)
Please do not operate until the sewing machine is repaired when any damage or fault is found on the
sewing machine at the installation.
(4) Please do not refurbish the sewing machine.
(5)
If the table and the steel stand are not MITSUBISHI original, the table and the steel stand have to be
strong enough to withstand the weight and Vibration of the sewing machine.
(6) When fitting the caster to the steel stand that are not MITSUBISHI original, the caster with locking
function has to be strong enough to withstand the weight and Vibration of the sewing machine.
3-1. Preparation of the table
If the table is not MITSUBISHI original, the thickness of the table is required to have 40mm more.
And please refer to the cut out table drawing for your own preparation.
The cut out drawing is shown on the last page of this technical manual asAPPENDIX 6 drawing.
3-2. Preparation of the steel stand
If the steel stand is not MITSUBISHI original, please refer to the assembling drawing for your own
preparation.
The assembling drawing is shown on the last page of this technical manual asAPPENDIX 6 drawing.
If the steel stand is MITSUBISHI original, please assemble the steel stand with the assembling
instructions enclosed in the packing.
3-3. Installation of the motor
If the motor is purchased without assembling to the table, the motor has to be installed underneath
the table.
Please install the motor with the instructions explained in the paragraph [installation of the motor] on
the another [CONTROL UNIT] technical manual.
3-4. Installation of the control box
If the control box is purchased without assembling to the table, the control box has to be installed
underneath the table.
Please install the control box with the instruction in the paragraph [installation of the control box] on
the another [CONTROL UNIT] technical manual.
3-5. Connection of the operation panel
Please install the operation panel referring following figure of control box backside view.
- 3 -

3-6. Installation of the power switch
(1) Mount the power switch (No.1) with the wood screw (No.2) underneath the table as shown on the
figure.
(2) Fix the electric cords with the staples (No.3) underneath the table.
(3) Hook up the connector of the power switch (No1) to the connector of the cable (No.4).
(4) Hook up the connector of the cable (No.4) to the CON B connector of the control box (No.6).
(5) Connect the terminal (No.10) of the cable in black (No.4) to the terminal adapter on the transformer
(No.8). Two terminal has been prepared on this transformer (for 210V and for 230V). Detail of wiring
are informed in APPENDIX 1 on this manual.
(6) Connect the other terminal (No.11) of the cable in white to the terminal adapter PORT No.5 of the
relay socket (No.9). Detail of wiring are informed in APPENDIX 1 on this manual.
These terminal adapter are located inside of the motor cover of machine head.
(7) Attach the power plug (No.12) to the another end of the power switch cord (No.5).
For detail description, please refer to APPENDIX 1 and 2 Wiring diagram.
[Notice] Power plug (No.12) is not included in accessory box.
3-7. Connection of the foot switch
Connect the foot switch (No.7) to CON H connector of the control box (No.6).
Details are informed in [3-11. Connection of the electric cables] on this manual.
<2>
<1>
<3>
<5>
<6>
<7>
<8>
<9>
<4>
<12>
<10> <11>
- 4 -

3-8. Installation of the oil pan
(1) Assemble the oil pan (No.1) and oil bottle (No.2) which are enclosed in the accessory box.
(2) Insert the oil bottle (No.2) into the table top cut-out hole.
(3) Install the oil pan (No.1) fit with the table front edge.
(4) Fix the oil pan (No.1) at its four corners on the table top with four staples (No.3) en-closed in the
accessory box.
3-9. Installation of the sewing machine head
CAUTION
(1) The sewing machine
is heavy. For the safety, please make sure to install the sewing machine head
by more than one person.
(2)
When tilting the sewing machine, please stand at the hinge side and hold the sewing machine with
both hands.Also, please lock the caster on the steel stand.
(1) Make sure to hold the machine table with the caster stopper.
(2) Fit the rubber cushion pads (No.4) into the each hole on the table top. The rubber cushion pads
(No.4) are enclosed in the accessory box.
(3) Put the sewing machine head on the table top and set the each leg to the each rubber cushion
pad (No.4).
<1>
<2>
<3>
<4>
<5>
<7>
<9>
<6>
<8>
- 5 -

(4) Attach two hinges (No.5) temporarily, with the hexagonal socket head set screws (No.6)
fastening with the thread holes light, on the left side surface of the machine bed. At this time, take
notice of the E-shaped snap ring must be come to the behind.
(5) These parts are all enclosed in the accessory box.
(6) Fit the screw holes of the hinges (No.5) to the bolt setting holes on the table top then, pass the
bolt (No.7) through these holes and fasten the bolt (No.7) to fix the hinges (No.5) with the flat
washers, the spring washers and the nuts (No.8).
(7) Fasten firmly hexagonal socket head set screws (No.6) which set the hinges (No.5) temporarily
at above procedure (4) then, fix the hinges (No.5) perfectly.
(8) Insert the head support stand (No.9) into the hole on the table top.
3-10. Installation of the V-belt
(1) Put the V-belt (No.1) across the sewing machine
pulley (No.2) and the motor pulley (No.3) with
passing it through the slit on the table top.
(2) The V-belt (No.1) is enclosed in the accessory
box.
(3) Push the center portion of V-belt by the finger with
the pressure of about 0.1 N (1 kgf). If the V-belt
tension is proper, it should be yielded about
10mm. If the V-belt tension is not proper, please
adjust it with changing the motor setting position
with loosening the nuts (No.4).
[Notice]About the motor pulley (No.3) it is necessary to
use only PLK-G2008H accessory. Other motor
pulley for the PLK-E1008H/2008H and
PLK-B1008H are different in size. Please do not
use that kind of motor pulleys.
Suitable motor pulley
PLK-G2008H : T85 / PLK-E1008H/2008H :T100
/ PLK-B1008H : T100
NOTE The V-belt becomes loose after a long period
machine running. If the looseness is recognized
definitely, firstly turn the power OFF then adjust
the V-belt tension again as the above procedure.
3-11. Connection of the electric cables (Refer to the figure on the following page)
CAUTION
(1) Please make sure to ground the place where there is a mark. Failure to do so may cause electric
shock and or malfunction.
(1) Remove the stepping motor cover from sewing machine head.
(2) Connect the machine head, motor and the control box with cables as shown on the figure.
- 6 -

(3) Fix the X-Y spindle motor cable (No.6) with the nylon clip (No.8) on the sewing machine head
which enclosed in the X-Y spindle motor cable set.
(4) Hold the dangling cables under the table with accessory tie holders (No.9) and cord ties (No.10).
At this time, please check whether the cables are not pulled when tilting the sewing machine.
(5) Fix the cables with staples (No.11) as needed.
CON A: Operation panel
CON B: Power supply
CON C: Various solenoid DC power
CON D: Spindle motor
CON E: Various solenoid
CON F1: Detector
CON F2: Spindle encoder
CON G: X-Y spindle encoder
CON H: Foot switch
CON J: X-Y spindle stepping motor
<1>: Solenoid cable <2>: Solenoid power cable <3>: Detector junction cable
<4>: Spindle motor encoder junction cable
<5>: X-Y spindle encoder cable (X and Y different has exist)
<6>: X-Y spindle motor cable <7>: Spindle motor junction cable <8>: Nylon clip
<9>: Tie holder <10>: Cord tie <11>: Staple
<1>
<2>
<3>
<7>
<5>
<6>
<4> Y
X
<5>
<6>
<8>
<9>
<10>
CON B
CON C
CON D
CON G
CON J
CON A
CON E
CON F1
CON F2
CON H
<11>
Spindle motor cover
- 7 -

3-12. Installation of the belt cover
(1) Attach the belt cover mounting plate (No.1, 2) to the sewing machine head with the set screws
(No.3).
(2) Put the belt cover (NO.4) on to the mounting plate with set screws (No.5).
3-13. Installation of the thread stand
(1) Assemble the parts (No.1 to No.11) of the thread stand as shown on the figure.
(2) Fit the thread stand into the hole at the far right on the table stand with the nut (No.13) and the
washers (No.12).
<1>
<12>
<3>
<4>
<6>
<7>
<8>
<9>
<2>
<10>
<11>
<5>
<13>
<1>: Upper column pipe
<2>: Lower column pipe
<3>: Spool stand base (two stand bases)
<4>: Spool mat (two mats)
<5>: Spool holder (two holders)
<6>: Spool shaft (two shafts)
<7>: Spring washer (two washers)
<8>: Nut (four nuts)
<9>: Thread hunger
<10>: Spool holder
<11>: Column joint
<12>: Washer
<13>: Nut
- 8 -

3-14. Connection of the air tube
(1) Remove the spindle motor cover.
(2) Attach the air pressure regulator assembly (No.1) underneath the table with the wood screws
(No.2). These are enclosed in the accessory box. There are pilot holes for the wood screw on the
undersurface of the table..
(3) Cut the part of size ø8 air tube (No.3) enclosed in the accessory box into about 1.5 meter length
then, insert one end of this air tube into the air fitting (No.5) of the manifold (No.4). The manifold
is jointed with the magnet valves and located at the left side surface of the sewing machine head.
Beside, pass the other end of the air tube (No.3) through the cut out hole of the table top then,
insert it into the air outlet fitting (No.6) of the air pressure regulator (No.1).
(4) Join the other end of the resting tube with the suitable air coupling to be adopted with the air
supply source provided in your factory. One of the air couplings is enclosed in the accessory box.
<1>
<2>
<3>
<4>
<6> <5>
<7>
- 9 -

4. LUBRICATION
CAUTION
(1) Please make sure to turn power switch off before lubricating.
(2) Please pay attention that oil does not get on your skin or in your eyes as it
may cause an
inflammation.
(3) Please make sure to keep oil out of the reach of children who may drink oil by mistake.
[Notice] Please make sure to lubricate when operating for the first time after the installation. Also, please
make sure to check the amount of oil when the machine has not been used for a long time.
NOTE Please use high quality white machining oil.
Put some oil to red marked oil holes and other part as described below arrow sign.
<5><4> <6> <7>
<2>
<1> <3> <9>
<8> <10>
<11>
<12>
<13>
<14>
<15>
<16>
<17>
<1>: Presser foot mechanism <2>: Rock shaft bushing <3>: Crank rod
<4>: Thread take up cam <5>: Thread take up shaft <6>: Arm shaft bushing left
<7>: Foot lifting eccentric <8>: Arm shaft bushing middle <9>: Connecting rod
<10>: Arm shaft bushing right <11>: Hook shaft bushing left <12>: Hook shaft bushing right
<13> to <16>: Presser foot mechanism <17>: Hook, driver
- 10 -

5. PROPER OPERATION
5-1. Initial setting of the control box
When using the sewing machine for the first time, the model and the language of the sewing machine in
use have to be set.
Refer to the instructions in the paragraph “[6] Initial Setting of System (Model/language Setting)” in the
CONTROL UNIT technical manual.
5-2. Initial setting of the setting table
For the thermal trimming system function it is necessary to initial setting of setting table. Please perform
the procedures below.
[Notice] If this setting not performed the thermal trimming system does not function.
5-2-1. Reading of the Setting table／Step file
(1) Turning on the power supply
While holding down the [F] key on the front panel of the control box, turn the machine power ON.
(Keep pushing [F] key until red LED on the front panel is turned on.)
(2) Setting of the Setting table／Step file
Press .
(3) Setting table／Step file reading mode
Press
To the connector on the front panel of the control
box, connect the USB memory [*1] for initial
configuration that comes, please press .
[*1] If the USB memory for initial configuration that
comes with is not available on the loss, etc., refer
to the section of this technical manual "5-2-2. How
to create a USB memory for initial configuration",
please create a USB memory.
2 0 0 8 H
+
- 11 -

(4) The screen to select the step file is displayed. Please
choose the [2008HT * * ] by using up and down
arrow button. (The * * mark displays file version.)
[Notice] Please make sure that the file name
[2008HT * * ] is selected correctly. If you
are set in different file names, it may cause
a malfunction.
Press .
(5) The screen to select the setting file is displayed.
Please choose the [2008HT * * ] in the same way.
[Notice] Please make sure that the file name
[2008HT * * ] is selected correctly. If you
are set in different file names, it may cause
a malfunction.
Press .
(6) Re-turning on the power supply
Please turn the power off the message "M-290：READING COMPLETE" appears.
(7) After check the LED lamp has completely off on the front panel of the control box,
turn the power on.
2 0 0 8 H T * *
2 0 0 8 H T * *
Check the LED lamp is OFF
- 12 -

(8) Initial condition
Message "M-006：PATTERN DATADOES NOT EXIST" appears, press , please switch
to the standard screen.
(It does not appear when the sewing data is
stored.)
5-2-2. How to create a USB memory for initial configuration
If the USB memory that came with is no longer available in the loss, etc., please create a USB memory for
initial configuration in the following manner.
Coping setting table of the CD-ROM (PLK-G Document CD) to the USB memory by using copy tool.
PLK-G Document CD is enclosed in packing box of the operation panel (PLK-G-PAL).
[Note] If “ ”is already exist in the USB memory, they are over-written.
(Please move other important data to other folder or memory before using copy tool.)
(1) Inset the CD-ROM (PLK-G Document CD) to your PC.
Insert USB memory to the USB connector on your PC.
Check the CD-ROM drive and USB memory drive.
(ex. CD-ROM drive= “D:” , USB memory drive = “E:”)
(2) Open the CD-ROM root directory by using exploler etc.
Double click “PLKG System Setup.exe”
(3) After open the PLKG System Setup window, select CD-ROM drive and USB memory drive
respectively.
――――――――
―――
- 13 -