Mitsubishi Electric BR-LM1KK User manual

ENGLISH
EN-1
WALLMOUNTBRACKET
MODEL
BR-LM1KK
for LM55S1, LM55P1, LM46P1
QuickStartGuide FORINSTALLER
Be sure to follow the directions below.
This product requires special installation to prevent
falling or toppling.
Please ask installation specialists for installation.
Don’t attempt to install this product by yourself.
It is necessary to install properly in order that this product perform sufficiently and the safety ensure.
Please read User’s Manual, User’s Manual of LCD display and Set-up Manual before installing the product.
For Set-up Manual, please contact the distributor.
Separate “User’s Manual” is for your customer.
Please pass your customer “User’s Manual” with “Quick Start Guide” after installing the
product. Please ask your customer to keep it with “User’s Manual”.
W
arning:

EN-2
Contents
1Safety precaution ..................................................................................................................................................................3
2Preparation ..............................................................................................................................................................................4
3Display attaching...................................................................................................................................................................8
3.1 Display mounting .........................................................................................................................................................8
3.2 Display open / close.................................................................................................................................................. 10
3.3 Panel gap adjustment.............................................................................................................................................. 10
4Check after installing ........................................................................................................................................................ 11

ENGLISH
EN-3
1
1 S Sa af fe et ty y p pr re ec ca au ut ti io on n
This product requires special installation to prevent falling
or toppling. This should be done by installation specialists.
Be sure to read this manual and the user’s manual of the
display for your safety before starting assembly or
installation.
Be sure to use supplied accessories for assembly or
installation.
Attach all the screws and fixtures specified in this manual
securely.
Do not dissolve or revamp the product except the areas
which are specified in this manual.
Inspect the mounting fixings more than once in a year as
needed.
Do not install the display with its intakes, exhaust slots and
ventilation holes blocked. The display may overheat and
cause a fire or breakdown.
To mount on a wall
Before mounting,checkthestrengthofthewall.Mountonawall
whichsafetyfactorismorethan6(orensurethatitcanbearsix
timesthesumoftheweightsofproductsandthemountbrackets).
Whenitisnotsufficient,reinforcethewallsurface.
The weights of the displays and wall mount bracket
LM55S1: 37kg、LM55P1: 37kg、LM46P1: 24kg
BR-LM1KK: 12kg
Carefully install onto the wall not to get loose due to
vibration etc. Wrong installation or installation with
insufficient strength causes the product to fall resulting in
a serious accident or injury.
The weights shall be borne by a sturdy structural material
such as a joist. Secure the bracket using bolts, spring
washers, washers, and nuts.
Don’t install the bracket directly on a wall having
insufficient strength, or don’t install it using wooden
screws or anchor screws. Also don’t install it on wooden
structural materials or blocks.
Install the displays not to touch with adjacent panels. The
outer circumference of the panels is quite weak and hard
pressure or impact may cause damage.
Before installation, calculate cable length for external
connection and prepare them. Inappropriate length may
make the wiring difficult.
Do not put your hands in the back of panel while closing
the display. You may be injured to trap your finger in the
bracket or between the panels.
How to handle the display
Do not touch the top surface or left-hand surface as
viewed from the front surface of the display. Doing so may
cause failure.
When carryingthedisplay,makesuretohavetwopeoplecarryit
while holding onto the handles. In addition, being careful not to
tough the panel surface, cautiously support the bottom
surface of the panel.
Be careful not to twist or bend the display.
Be careful not to bump or apply pressure on the panel.
When laying the display flat, be sure to place the panel on
a flat surface with a something soft like a blanket
underneath, and be careful not to scratch the surface of
the panel or allow the panel to be subjected to excessive
pressure. Also do not leave the panel face-down for a long
while.
Protect the panel from static electricity.
To keep static buildup to a minimum, remove the
protective sheet on the panel surface slowly.
The surface of the panel is rather fragile and can be
damaged easily. Do not push down hard on it or scratch it.
Immediately wipe away any drops of water or oil that
adhere to the panel. Allowing water or oil to remain on the
panel for long periods of time may result in the panel
becoming stained or changing color.
Vertical tiling
In high configurations, the temperature condition gets
worse in the upper panels. The recommended stack
number in landscape orientation is up to 6, in portrait
orientation is up to 2. When over that configuration, it
requires an additional ventilation way to enhance the
efficiency.

EN-4
2
2 P Pr re ep pa ar ra at ti io on n
Tools
Prepare the following tools..
Necessary tools
Hex keys (4mm, 5mm)
Phillips screwdriver (#2)
Wrench (8mm)
Level
Stepladder
Bolt (M6 length over 50m)
The name of each part
Do not block the ventilation holes. The temperature inside
the display rises high causing a fire or breakdown.
Exhaust hot air gets stacked above the display. Create a
space around the displays so as to release it and flow
enough fresh air in from the bottom at least as shown
below. It should apply to the case of portrait orientation as
well. (unit: mm).
Hole locations on the wall
1Create following mount holes on the wall. (unit: mm)
Create the holes fixing the cable ties to clamp the cables
suitably.
Landscape
[LM55S1/P1]
[LM46P1]
4-M6 for Base bracket
2-M6 for Hoo
k
4-M6 for Base bracket
2-M6 for Hoo
k
Base bracket
Display
bracket (R)
Display
bracket (L)
Handle (R)
Handle (L)
B
o
l
t
(6 pcs)
W
as
h
er
(4 pcs)
Hook

ENGLISH
EN-5
Portrait
[LM55S1/P1]
[LM46P1]
2Remove in order ①2 display brackets (L/R), ②2 handles
(L/R), ③4 lock bolts.
3Place the panel on a flat surface with a something soft like
a mattress or blanket underneath.
Do not leave the panel face-down for a long while.
4Attach the display brackets (L/R) on the panel, which
brackets have been removed in the step 2. Use removed 2
Lock Bolts to fix each of them.
Carefully work not to bear down on the LCD panel hardly.
Do not attach the display bracket (L) and (R) by mistake.
Landscape
[LM55S1/P1]
[LM46P1]
2-M6 for Hook
4-M6
For Base bracket
2-M6 for Hook
4-M6
For Base bracket
Base bracket
Display
bracket (R)
Display
bracket (L)
Handle (R)
Handle (L)
Lock bolt
(4pcs)
Bolt, washer
R L
R L

EN-6
Portrait
In portrait orientation, always rotate top side right in
consideration of the panel holding structure.
[LM55S1/P1]
{LM46P1}
Need the metal fitting specialy. Contact your MITSUBISHI
dealer.
5Attach the removed handle (L) (without wire) on the right
lower corner of the panel seeing back side with the screws
that fixed it on the wall mount bracket.
When attaching, contact inside the handle with the panel
side surface closely.
6Attach the hook on the wall with suppied 2 Bolts.
7Starting from the panel at the center of the bottom row in
the display wall, spread to its both sides and go to upper
rows.
8Hang the base bracket at the center of bottom row (1) on
the hook.
9Shift the position of the base bracket in about 6 mm. Take
a level of the bracket. If bolt (M6 length over 50) is inserted
into two holes at the top of the bracket, it can lift the
bracket to tweak the vertical position.
Remove the bolts after adjustment
（2）（3）
（4）（5）（6）
（7）（8）（9）
（1）
Landscape
Portrait
Hook
Bolt (2 pcs)
Hook
Hook
M6 Bolt
Screw
hole
6mm
T
op
面
Top
Front
Front
R L

ENGLISH
EN-7
10 Fix the bracket on the wall with supplied 4 bolts and
washers.
11 Hang the brackets on the both sides, (2) and (3), on the
hooks. Align height with the center bracket (1) and
horizontal distance from one (refer to page 4 “Hole
location on the wall), and fix them on the wall.
12 For LM55S1/P1, remove 2 screws on the right and left
lower sides of the base bracket. Then slide the positioning
plate to the lower side, and fix it with 2 screws
This step is not neccessory for LM46P1, portrait and
bottom low in landscape for LM55S1/P1
13 Attach the bracket at the center of upper row (4). Insert
the protrusion on the top side of the lower bracket to the
angle hole on the bottom side of the upper bracket.
14 In the same manner, attach the brackets on the both
sides of it, (5) and (6).
15 Repeat the procedure to attach all brackets. Make sure
that the vertical and horizontal distance between all
brackets is proper (refer to page 4 ”Hole location on the
wall”).
Protrusion
Screws Positioning
plate

EN-8
3
3 D Di is sp pl la ay y a at tt ta ac ch hi in ng g
3.1 Display mounting
Starting from the panel at the center of the middle row in
the display wall, spread to its both sides and top / bottom.
Lastly fill the rest of areas.
1Press the release lever on right side of the base bracket.
Be careful not to bump into the front bar, since it opens
ahead.
2Draw the front bar to the front. Then lift and draw the lock
bar at the right lower side of the front bar to lock the front
bar.
3Hang the display brackets in the back of the panel on the
front bar so as to fit the hole and the protrusion toghether.
Carefully treat the panel not to touch with adjacent panels.
4Temporarily fix the panel with the bolts and washers
which were on the display brackets.
Screen gaps could not be adjusted if you fix the bolts
firmly
5Attach the handle(R) on the right upper side of the display
with 2 bolts that fixed it.
When attaching, contact inside the handle with the bezel
side surface closely.
（4）（6）（7）
（
（2）（3）
（5）（8）（9）
（1）
Opening
direction
Release lever
Front bar
Front Rear
Base bracket
Lift and draw the Lock bar
Handle (R)
2 bolts
Bezel side
surface
Bolts
Washers
Protrusion
Front bar
Base
bracket
Lock bar

ENGLISH
EN-9
6Tie the wire with the clampers attached to the display not
to .run it off the edge of the display.
Fix the wire on the back of the display not to pinch it.
Landscape
[LM55S1/P1]
[LM46P1]
Portrait
[LM55S1/P1]
[LM46P1]
7Adjust the position of the handle(R) to turn the
adjustment screw. Loosen the nut on adjustment screws
with wrench (8mm) before adjustment.
Contact the claw of the handle with the bezel front surface.
After the adjustment tighten the nut.
8In the same manner, adjust the position of the handle(L)
9Connect the cables to the display.
10 Tie the cables with bands supplied to the display not to
run the cables off the bottom edge when the panel is
closed.
The cables clamped on the wall are slacken off sufficienty
not to pull cables when the display is opened.
Holes for fixing Band
[LM55S1/P1]
[LM46P1]
Display dismounting
Be sure to dismount the display before take off Handle(R), it’s
wire and cables.
Clamper
Adjustment
screw
Claw
Nut
Band
Wire
Wire
Band
Clamper
Clamper
Band
Wire
Band
Band
Wire
Holes for
fixing Band
Holes for
fixing Band

EN-10
3.2 Display open / close
Display closing
Release the lock bar at the right lower side of the front bar to
lift and push it.
Push the panel lightly to slide till locked at the end.
Close it carefully not to touch adjacent panels.
Make sure that the closed panel doesn’t pinch the internal
cables.
Release the lock bar while holding the display to the front if
it is hard to release it.
Do not put your hands in the back of panel
while closing the display. You may be
injured to trap your finger in the bracket or
between the panels.
Display opening
Pull up the handes on both sides to draw the panel til
Release the display to pull up the handle(R) on the right sideof
the display. Open the display to draw the hadles on both sides.
Do not release the display to pull up the handle(L).
Lock the front bar with lock bar not to pinch the fingers and
so on when the display is opened (refer to page 6 “3.1 step
2”).
3.3 Panel gap adjustment
Flat surface shift
Loosen the nuts on V position adjustment screws with
wrench (8mm) before adjustment. Turn the adjustment
screws with a 4mm hex key. One turn of the screws shifts the
display approximately 0.8mm.
Close the panel to check the gap and repeat the steps until
the gaps being about 1mm.
Front / back direction
Loosen the nuts on adjustment screws with wrench (8mm)
before adjustment. Turn the screws with a 4mm hex key to
adjust. There are 4 screws in total on both sides. One turn of
the screws shifts the panel approximately 1.5mm. Tighten
the nuts after the adjustment.
The shifting direction is opposite on upper and lower
screws. By clockwise turning, the upper screws shift the
panel top to the back direction, while lower screws shifts
the panel bottom to the front.。
After the all adjustment, firmly tighten the bolts on the
display brackets on both sides which have been fixed
temporarily and all nuts of adjustment screws.
Handle (R)
V position : R
(other side : L
H position adjustmnet scrw
H position
Nut V position : R
V position : L
Adjustmnet screws
(4 points)
Nuts
1mm
1mm
Rear
Base bracket
Closing
direction
Lift and push the lock bar
Front bar
Front
The
Lock bar

ENGLISH
EN-11
4
4 C Ch he ec ck k a af ft te er r i in ns st ta al ll li in ng g
Check in according with the following checklist after installing.
Be sure to take measures if there is any fault. (Performance is not only be exhibited, but safety can not be ensured.)
Item Measures in case of a fault Check
- Is the strength of the wall enough? Reinforce the wall. □
- Are the intakes, exhaust slots and ventilation holes blocked? Eliminate any objects blocking. □
-AreBracket(L)and(R)attachedbymistake? Attach Bracket (L) and (R) correctly. □
- Do the circumference surface of the display touch adjacent panels? Adjust panel gap □
- Are the bolts tightened securely?
Hook 2pcs
Base Bracket 4pcs
Display Bracket L/R each 2pcs
Bolts for fixing Display Bracket L/R each 1pcs
Handle L/R each 2pcs
Tighten the bolts. □
- Are the cables slacken off sufficiently not to pull them when the
display is opened? Slacken off the cables sufficienty. □
- Do the cables run off the panel edge when the panel is closed? Tie the cables with cable ties. □
- Are the handles adjusted to contact the claw with the bezel front
surface? Adjust the position of the handles. □