Mitsubishi WD 6500 User manual

MITSUBISHI
THE BIG SCREENCOMPANY _
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
\ literature accompanying the appliance.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or more of the following meas-
ures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equip-
ment.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOIS-
TURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CATV SYSTEM INSTALLER:
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO SECTION 820-40 OF
THE NEC WHICH PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT
THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE
TO THE POINT OF CABLE ENTRY AS PRACTICAL.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Table of Contents
IMPORTANT SAFEGUARDS ......................................................................................... 4-5
Appendix A: Bypassing the V-Chip Lock .................................................................................................. 57
Appendix B: High Definition Inputs Connection Compatibility .............................................................. 59
Appendix C: Remote Control Programing Codes .................................................................................... 60
Appendix D: Lamp Replacement ....................................................................................................... 61 -63
Appendix E: Cleaning and Service .................................................................................................... 64 -66
Filter cleaning ................................................................................................................................ 64 -65
Appendix F: Troubleshooting ............................................................................................................. 67 -68
Index ..................................................................................................................................................... 69 -70
Mitsubishi Projection TV Limited Warranty ............................................................................................... 71
Trademark, Registered trademark
Digital Light Processing TM and DLP TM are trademarks of Texas instruments.
IBM and VGA are trademarks or registered trademarks of International Business Machines Corporation.
Other brand or product names are trademarks or registered trademarks of their respective holders.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

IMPORTANT SAFEGUARDS
Please read the following safeguards for your TV and retain for future reference.
Always follow all warnings and instructions marked on the television.
1. Read, Retain and FollowAII Instructions
Read all safety and operating instructionsbefore operating the TV. Retain the safety and operating instruc-
tions for future reference. Follow all operating and use instructions.
2. Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.
3. Cleaning
Unplug the TV from the walt outlet before cleaning. Do not use liquid, abrasive, or aerosol cleaners. Cleaners
can permanently damage the cabinet and screen. Use a lightly dampened clothfor cleaning.
4. Attachments and Equipment
Never add any attachments and/or equipment without approval ofthe manufacturer as such additions may
result in the risk of fire, electric shock or other personal injury.
Water and Moisture
Do not use the TV where contact with or immersion in water is possible. Do not use near bath tubs, wash
bowls, kitchen sinks, laundry tubs, swimming pools, etc.
6. Accessories Do not place the TV on an unstable cart, stand, tripod, or table. The TV may fall, causing
serious injury to a child or adult and serious damage to the TV. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with the TV. Any mount-
ing of the TV should follow the manufacturer's instructions, and should use mounting acces-
sories recommended by the manufacturer. An appliance and cart combination should be
moved with care. Quick stops, excessive force, and uneven surfaces may cause the appli-
ance and cart combination to overturn.
Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the TV and
to protect it from overheating. Do not block these openings or allow them to be obstructed by placing the TV
on a bed, sofa, rug, or other similar surface. Nor should it be placed over a radiator or heat register. If the TV
is to be placed in a rack or bookcase, ensure that there is adequate ventilation and that the manufacturer's
instructions have been adhered to.
8. Power Source
This TV should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appliance dealer or local power company.
9. Grounding or Polarization
For your safety, this Projector is equipped with a three-wire grounding type plug having a third (grounding)
pin. This plug will only fit into a grounded type outlet. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-
type plug.
10. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the TV.
11. Lightning
For added protection for this TV during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug itfrom the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the TV due to lightning and power-line surges.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

IMPORTANT SAFEGUARDS Continued
12. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.
13. Overloading
Do not overload walt outlets and extension cords as this can result in a risk of fire or electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this TV through openings as they may touch dangerous voltage points or
short-out parts that could result in fire or electric shock. Never spill liquid of any kind on or into the TV.
15, Outdoor Antenna Grounding EXAMPLEOFANTENNAGROUNDING
If an outside antenna or cable system is connected to the TV, be __1'_- s
sure the antenna or cable system isgrounded so as to provide _E_E
some protection against voltage surges and built-up static charges. _ROUNOOLAMP
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, _,_N_EU.,_
provides information with respect to proper grounding of the mast <,_cs_c_o._0-_o)
and supporting structure, grounding of the lead in wire to an an- G_ou,o,._
CONDUCTORS
tenna discharge unit, size of grounding conductors, location of _°-_
antenna discharge unit, connection to grounding electrodes, and -_
requirements for the grounding electrode. _POWERSERV_CEGROUNDING
ELECTRODE SYSTEM
16. Servicing ._o ._,o._o_R,o_Looo_<._o_0,_.)
Do not attempt to service this TV yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
17. Damage Requiring Service
Unplug the TV from the walt outlet and refer servicing to qualified service personnel under the following
conditions:
(a) When the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the TV.
(c) If the TV has been exposed to rain or water.
(d) If the TV does not operate normally by following the operating instructions, adjust only those controls
that are covered by the operating instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the TV to its normal
operation.
(e) If the TV has been dropped or the cabinet has been damaged.
(f) When the TV exhibits a distinct change in performance - this indicates a need for service.
18. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
19. Safety Check
Upon completion of any service or repair to the TV, ask the service technician to perform safety checks to
determine that the TV is in safe operating condition.
20. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
21. Magnetic field
Objects producing astrong magnetic field, suchas a magnet, speaker ormotor, should notbe placed on or near theTV.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part I :ThankYou
We at Mitsubishi Would Like to Thank You
To the Mitsubishi Consumer:
Thank you for choosing Mitsubishi as your premier home
entertainment partner. Whether this is your first Mitsubishi
consumer electronics product or an addition to your grow-
ing Mitsubishi family, you should be proud and delighted
for choosing one of the most technologically advanced
big-screens available today.
True high definition multimedia requires a large, precise
display, the smart circuitry to drive it, and an assortment of
inputs for a wide variety of sources. To that end Mitsubishi
went a step beyond the Diamond Series TM and developed
the WD-650001. We selected DLP TM Technology, one of the
most significant advances in projection TV displays since
the introduction of the CRT. DLP TM Technology has the im-
pressive ability to display both television pictures and
computer images with a level of detail, color, and clarity
that has never before been offered for the home theater.
When you look at your new Mitsubishi bigscreen televi-
sion, please see all of us who built it, because when we
build it, we see you.
Thank You Again,
The Mitsubishi Team
1. With the addition of an HDTV digital receiver, all Mitsubishi HD-Upgradeables will offer uncompromising True
TM
HDTV high definition performance.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Unpacking Your New TV
Please take a moment to review the following
list of items to ensure that you have received
everything included:
[] Remote Control
[] (2) _Batteries
[] (3) IR Emitter Cables
[] Power-Cord
[] Product Registration Card
[] Owner's Guide
[] Quick Reference Card
QG
_,, mTSUBISH
[] Remote Control
[] (3) IR Emitter Cables
[] (2)AAA Batteries
[] Power-Cord
Send Slis
card into
register your
purchase
[] Product Registration Card
Part I: Thank You
Special Features
Your new HD Upgradeable bigscreen televi-
sion has many special features that make it
the perfect addition to your home entertain-
ment system. Below we have highlighted a
handful.
DLP TM Technology
DLP TM Technology has the impressive ability
to display both television pictures and com-
puter images with a level of detail, color, and
clarity that has never before been offered for
the home theater. The advanced circuitry has
the ability to accept:
•Conventional video (480i)
•Progressive scan video (480p)
•Both 1080i and 720p HDTVimages
•VGA, S- VGA, andXGA computer graphics
HD Upgradeable
With the use of an optional D-IV receiver like
the Mitsubishi SR-HD500 or similar model,
your Mitsubishi bigscreen can display high
definition pictures.
See pages 20 -21.
Wide Screen Picture Format
You will be able to view pictures as the direc-
tors intended you to see them. Both DTV and
DVD's supporting the widescreen format will
enable you to enjoy a theater feel in the
comfort of your home.
See pages 54 - 55.
PIP/POP Viewing Option
Using Picture-in-Picture and Picture-outside-
Picture will give you exciting options for
viewing your favorite programs.
See pages 52- 53.
V-Chip Technology
Mitsubishi understands that you may want to
shield certain viewers from specific program
content. Your Mitsubishi bigscreen will allow
you to restrict programming by general con-
tents, specific contents, or even by time.
See pages 36 -38.
Multibrand Remote Control
Your Mitsubishi remote controlcan be pro-
grammed to control many other audio/video
components.
See page 26- 29.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part II : Installation
Front Control Panel
Many remote control buttons are duplicated on the front control panel. These buttons are shaded in figure 1.
Please see Remote Control Functions, pages 48 - 55, for an explanation of their usage.
@ ©
PC-2 r-- INPUT- 5 --1
[] S-WDEO[] WDEO L-AUD_O-_R[]
[] [] ........................................................................n.......... [@ e e]
Figure f. Front ControI Panel
[] Status indicator
Figure 2. Located under Control Panel Overhang
This indicator informs of the status of the projection TV. See below.
[] Power indicator
This indicator informs of the power condition of the projection TV. See below.
Undernormaloperation
STATUSPOWERCONDITION NOTES
off off Off
• _ Initialization when first plugging inyour TV, or lamp cooling
off Steady (10 - 45 seconds)
lpd
off Steady Lamp start-up (for 30 seconds)
ye_bw
•TV will turn on in 10 - 3Oseconds.
off Steady The POWER is ON
g_pe_
off BE,_ki_ Stand-by (When the TV is set to turn on at a specific time.)
9_een
Abnormaloperation notice
STATUSPOWER CONDITION POSSIBLE SOLUTIONS
_ • Unusual temperature
B_E,_g Off " The air-filter is dirty. • Clean the filter. (See page 64).
• The room temperature is too high. • Relocate the projector to a cooler place.
My _t_t_ Lamp usage warning. (Usage total about 4,000 hours.) • Replace the lamp. (See page 61.)
_(_ • Lamp failure • Wait 1minute, then pressthe POWER button.
_Ei_ng Off • ifthe above operation isnot effective, replace
red/_reen the lamp.
_ • Lamp cover or filter cover is open. •Close the cover correctly.
SEining Off
¢e_Dw/g_e_n
• _( • Service required. •Contact your dealer.
Blinking Off
red
[] AN Reset
Press this button to reset the A/V memory on all inputs to the factory default settings. Please
see A/V Memory Reset, page 41, for instructions.
[] PC-2
This input can be used for the convenient connection of a compatible computer. Please see
Appendix B, page 59, for signal compatibility.
[] Input 5 (S-VIDEO /VIDEO)
This input can be used for convenient connection of a camcorder or other video device. Please
note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated.
[] L- AUDIO - R
Audio input to the AUDIO IN terminal on the front panel is possible for a component connected
to either PC-2 or Input 5.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Back Panel
Part I1: Installation
AUDIO*L
60 Hz AUDIO*R
AUDIO_L
_,UDIO*R
[]
AUDIO-RI
[] Inputs 1-4
These inputs can be used for the connection of a VCR, Super VHS (S-VHS) VCR, laser disc
player, or other A/V device to the TV. Please note that if you connect to the S-VIDEO terminal,
the VIDEO terminal is deactivated. The VIDEO terminal is active when there is no S-Video
connection.
[] Output (Monitor and PIP)
The Monitor Output sends the TV audio and video signals, excluding component video, PC, or
DTV video, to an A/V receiver or other equipment. The PIP output sends the PIP's or POP's
audio signal to an amplifier or wireless headphones. If no PIP or POP is displayed, the PIP
output will send the main picture audio signal.
[] Antenna (ANT-A, LOOP OUT, and ANT-B)
ANT-A and ANT-B receive signals from VHF/UHF antennas or a cable system. LOOP OUT
sends the ANT-A signal out to another component, such as a cable box or VCR.
[] IR-Emitter (System 4 Home Theater IR Control)
Connecting an IR emitters here allow the TV to automatically change a digital A/V receiver's
input in a home theater setup, and pass IR commands to other A/V devices.
[] Component Inputs 1-2
These inputs can be used for the connection of A/V equipment with component video
devices, such as a DVD player. Please see Appendix B, page 59, for signal compatibility.
[] DTV Input
This input is used to connect a DTV receiver, and can be configured for HDTV component
video (Y/Pb/Pr), RGB Sync on green, or RGB plus H&V. Please see Appendix B, page 59, for
signal compatibility.
[] PC-1
This input can be used for the connection of a computer. Please see Appendix B, page 59, for
signal compatibility.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part II : Installation
How Connections Affect the PIP and POP
To see a picture in the PIP or POP inset, you
may need to select an input source. If the
only input connected is ANT-A, then both the
main picture and the PIP/POP insert will be
from that input source. If other video equip-
ment is connected, you may be able to view
these input sources as the PIP/POP insert.
When connecting your new Mitsubishi
bigscreen, it is important to understand
which main picture and PIP/POP input
sources can and cannot be used together.
Table 1 shows which inputs can and cannot
be used together and the limitations they
may require. To see if480i, DTV 480p, 720p,
1080i, Component-1 or Component-2 480p is
being displayed as the main picture, press
INFO on the TV remote control. The on-screen
display, figure 1, will list 480i, 480p, 720p, or
1080i when those signals are being received.
See Operation of PIP and POP, pages 52 - 53,
for operating instructions.
An asterisk (8) displayed after the signal type
indicates that the signal being received is a
non-standard format. A non-standard format
signal may or may not display properly in a
PIP/POP inset. Whenever the DTV input re-
ceiving a non-standard 1080i signal such as
Sharp box, an asterisk (8) displayed after the
signal type.
Table 1.
OK + NO PIP/POP OK OK OK
OK OK* OK OK OK
OK OK OK** OK OK
OK OK OK OK** OK
OK OK OK OK OK**
NO PIP
*No Side-by-Side with the same channel.
**No Side-by-Side with the same input.
PiP cannot display PC.
DTV
Component-1
4:09 AM
TUESDAY
Figure 1. On-screen display will show 480i, 480p,
720p, or I080i when those signals are being received.
How Connections Affect the
System 4 Home Theater IR
Control
The Mitsubishi System 4 Home Theater IR
System Control is a special feature that makes
it easier to use your TV with a digital surround
sound A/V receiver. Once your equipment is
properly connected and set up, your TV and
digital A/V receiver will change inputs to-
gether, to match high resolution pictures with
the proper surround sound.
When you change inputs on your TV to watch
different video products, your TV will send
signals via your remote control to the infrared
emitters to your digital A/V receiver to
change inputs. You will automatically hear the
high quality digital surround sound from
digital products like your DTV receiver and
DVD player, and high quality analog stereo or
surround sound from non-digital products like
your VCR.
Additionally, all IR remote signals from your
Mitsubishi remote or other manufacturers
remote will be passed through your TV to
your A/V devices.Your A/V devices can be
hidden or behind cabinet doors and con-
trolled by pointing the remote at the TV.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part I1: Installation
SpecialSetups:ANEquipment(ForSystem4 HomeTheaterIR Control)
VCR: Connect the cables to the TV as
directed on page 17, with one exception.
Connect the audio output connection to the
appropriate input on the back of the A/V
receiver (as shown in table 1).
Digital Input Assignment for DTV: As-
sign the digital input you used for DTV to
the A/V receiver's DTV input selector. This
procedure is explained in yourA/V receiv-
er's Owner's Guide.
DVD: Connect the cables as directed on
page 19 (using the COMPONENT-1 input),
with one exception. Connect the digital audio
output connection on the DVD player to the
appropriate digital input on the back of the
digital A/V receiver (as shown in table 1).
Infrared Emitter: Connect as shown on
page 22.
Special Setups:TV
DTV: Connect the cables as directed on
pages 20 - 21, with one exception. Connect
the digital audio output connection on the
DTV receiver to the appropriate digital input
on the back of the digital A/V receiver (as
shown in table 1).
AN Receiver: Connect as directed on page
18, with two additions. Use a S-Video cable
in step 1 if you have a S-Video VCR. The TV
outputs should be connected to the AN
receivers input marked TV.
•Auto Standby: ON (See your A/V receiv-
er's Owner's Guide for this procedure). For
all TV use, the sound will come from the A/
V receiver. Not available with all
A/V receivers.
• Digital Input Assignment for DVD: As-
sign the digital input you used for your
DVD player to the A/V receiver's DVD
input selector. This procedure is explained
Menu selection for A/V connections. Dace 42.
• TVSpeakers: OFF
• Audio Output: Fixed
• TV Inputs Appropriately Named : See
Assign Input Menu, page 33.
Remote Control. pages 26 - 27.
• Set the slide switch to the TV position and
follow the programming instructions using
the A/V receiver code appropriate for your
A/V receiver, page 27 (figure 5).
in your A/V receiver's Owner's Guide.
Brand Model The products listed at the top of this column connect to the below listed inputs on the
TV /Cable back of the appropriate A/V receiver. SAT/DBS/DTV VCR DVD
Mitsubishi M-VR1000/M-VR800 TV VCR2 VCR1 DVD
Mitsubsihi M-VR900/ M-VR700 TV CABLE/DBS VCR DVD
Denon AVR2800 TV/DBS VCR2 VCR1 DVD/LD
JVC RX-888V TV VIDEO 2 VCR 1 DVD
Kenwood VR-2080 AV AUX LD VIDEO 1 DVD
Onkyo TX-DS575 VIDEO 3 VIDEO 2 VIDEO 1 DVD
Pioneer VSX-21 TV/SAT VIDEO 2 VCR 1 DVD/LD
Sony STR-DE825 TV/DBS VIDEO 2 VIDEO 1 DVD/LD
Yamaha RX-V2095 TV/DBS VCR 2 VCR1 DVD/LD
Table 1. A/V receiver back panel input table
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part II : Installation
Connecting an Antenna, Wall Outlet Cable, or Cable Box
Separate UHF and VHF Antennas
(Figure 1)
[] Connect the UHF and VHF antenna leads
to the UHFNHF combiner.
[] Push the combiner onto ANT-A on the TV
back panel.
[] UHF/VHF combiners are not provided with
the TV. They should be available at most
electronic stores.
VHF Antenna UHF Antenna
(Channels 2-13) (Channels 14-69)
300 Ohm to
75Ohm
Comb_ne_
Back Side
TV back panel
Figure 1. Connecting separate UHF and VHF
antennas.
Twin Lead Antenna, Coaxial Lead
Antenna, or Wall Outlet Cable
For antennawith twin flat leads (Figure 2)
[] Connect the 300 ohm twin leads to the
transformer.
[] Push the 75 ohm side of the transformer
onto ANT-A on the TV back panel.
[] 300 ohm to 75 ohm matching transformers
are not provided with the TV. They should
be available at most electronic stores.
For cable or antenna with coaxial lead (Figure 2)
[] Connect the incoming cable to ANT-A on
the TV back panel.
0 hm lat
TV back panel
t_rn 75 Ohm
Figure 2. Connecting twin lead antenna, coaxial
lead antenna, or wall outlet cable.
Cable Box
(Figure 3)
[] Connect the incoming cable to ANT-A on
the TV back panel.
[] Connect two coaxial cables as follows:
[] One from LOOP-OUT on the TV back
panel to IN on the cable box back panel.
[] One from OUT on the cable box back
panel to ANT-B on the TV back panel.
_ncoming
Cable
TV _ack pa_e_
Figure 3. Connecting the cable box.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part I1: Installation
Connecting a VCR
InComing
CatJ_e
_-[]
Wbaokpanel _
Figure 1. Connecting VCR with antennas or wall
outlet cable.
Cable
TV back panel
Cable Box
Rear Terminals
@
[] VCR back panel
t¸ _ i _ _
[] _ ®_ii® _'ii'®
Figure 2. Connecting VCR with cable box.
TV back panel
©
VCR back panel
channel or RF ON/OFF
sw_tch, set to OFF
Figure 3. Connecting the VCR Audio/Video.
Antennas or Wall Outlet Cable
(Figure 1)
[] Connect the incoming cable to ANT-A on
theTV back panel.
[] Connect two coaxial cables as follows:
[] One from LOOP-OUT on the TV back panel to
ANTENNA IN on the VCR back panel.
[] One from VCR back panel ANTENNA
OUT to ANT-B on the TV back panel.
[] Now complete figure 3, step 1 - 2.
Cable Box
(Figure 2)
[] Connect the incoming cable to ANT-A on
theTV back panel.
[] Connect three coaxial cables as follows:
[] One from LOOP-OUT on the TV back
panel to IN on the back of the cable box.
[] One from OUT on the back of the cable box to
ANTENNA IN on the VCR back panel.
[] One from ANTENNA OUT on the VCR back
panel toANT-B on the TV back panel.
[] Now complete figure 3, step 1 - 2.
Composite Video with Audio or S-Video
with Audio
(Figure 3)
[] Connect a video cable from VIDEO OUT on
the VCR back panel to VIDEO INPUT-l, IN-
PUT-2, INPUT-3, or INPUT-4 on theTV back
panel or INPUT-5 on the TV front panel.
[] If you have a S-VHS VCR, follow the
same steps using the S-Video terminals
on the VCR and TV (in place of the com-
posite terminals).
[] Connect a set of audio cables from AUDIO
OUT on the VCR back panel to AUDIO
INPUT-l, INPUT-2, INPUT-3, or INPUT-4
on the TV back panel or INPUT-5 on the
TV front panel. The red cable connects to
the R (right) channel and the white cable
connects to the L (left) channel. If your
VCR is mono (non-stereo), connect only
the white (left) cable.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part II : Installation
Connecting an Audio Receiver
Stereo Audio System
(Figure 1)
[] Connect the audio cables from AUDIO
MONITOR OUTPUT on the TV back panel
to TV IN or AUX IN terminals on the back
of the audio system. The red cable con-
nects to the R (right) channel, and the
white cable connects to the L (left) chan-
nel.
[] Turn off the TV's speakers through the
Audio/Video Menu, page 42.
[] Set the audio system's input to the TV or
AUX position to hear the TV's audio
through your stereo system.
TV back panel
Figure 1. Connecting the Stereo Audio System
AN Receiver
(Figure 2)
[] Connect a video cable or S-Video cable
from VIDEO MONITOR OUT on the back
of the A/V receiver to VIDEO INPUT-1 on
the TV back panel.
[] Connect a video cable from VIDEO MONI-
TOR OUTPUT on the TV back panel to
VIDEO TV IN on the back of the A/V re-
ceiver.
[] Connect a set of audio cables from AUDIO
MONITOR OUTPUT on the TV back panel
to AUDIO TV IN on the back of the A/V
receiver. The red cable connects to the R
(right) channel, and the white cable con-
nects to the L (left) channel.
TV back paneE
AV Receiver
£ack panel section
[] []
Figure 2. Connecting the A/V Receive_
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Connecting a DVD Player
Part I1: Installation
TVr_aek_nel
_m
_m
DVD 9_ck panel
Figure 1. Connecting the DVD player.
DVD Player with Component Video
(Figure 1)
[] Connect the Component Video cables from
Y/Cr/Cb or Y/Pr/Pb VIDEO OUT on the back
of the DVD player to COMPONENT-1 or
COMPONENT-2 on the TV back panel,
matching the correct components:
Ill y toY
[] Cr or Pr to Pr
[] Cb or Pbto Pb
[] Connect a set of audio cables from AUDIO
OUT on the back of the DVD player to
COMPONENTAUDIO Input 1 or 2 on the
TV back panel. The red cable [] connects
to the R (right) channel, and the white
cable [] connects to the L (left) channel.
[] If you have progressive DVD player, con-
nect the cables with same connection.
Connecting an S-Video Device
[]
,_
TWack_a_
iii¸ ii_ili;i_;
*VideoDev< ce
w_
[]
Figure 2. Connecting an S-Video Device.
S-Video Device
(Figure 2)
[] Connect an S-Video cable from VIDEO
OUT on the device back panel to VIDEO
INPUT-l, INPUT-2, INPUT-3, or INPUT-4
on the TV back panel or INPUT-5 on the
TV front panel.
[] Connect a set of audio cables from AUDIO
OUT on the device back panel toAUDIO
INPUT-l, INPUT-2, INPUT-3 or INPUT-4
on the TV back panel or INPUT-5 on the
TV front panel. The red cable connects to
the R (right) channel and the white cable
connects to the L (left) channel. If your
device is mono (non-stereo), connect only
the white (left) cable.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF

Part II : Installation
Connecting a DTV Receiver
DTV Connections and Adaptors
(Figure 1)
The TV back panel has 5 RCA-type connec-
tors, for the DTV connection. The back panel
of your DTV receiver may use RCA-type
connectors or BNC-type connectors. If your
DTV receiver comes with BNC type connec-
tions, you will need to purchase BNC to RCA
adaptors to connect the TV to the DTV re-
ceiver. These adaptors should be available at
most electronic supply stores.
BNC to A aptor
RCA BNC Fitted to
Adaptor Connector Connection
or
RCA
Connector
Figure 1. DTV connectors and adaptors.
DTV Receiver with Component Video
Connections
(Figure 2)
[] Connect the outside antenna, cable, or
satellite to ANT, or SATELLITE IN on the
DTV receiver (see your DTV receiver's
owner's guide for instructions, and cable
compatibility).
[] Connect the RCA-type cables from the Y/
Pr/Pb outputs on the DTV receiver to
HIGH RESOLUTION INPUT Y/Pr/Pb on
the TV back panel. You may need to set
the DTV input assignment to YPrPb in the
Assign Input Menu, page 33.
[] Connect the L (left) and R (right) audio
cables from the DTV receiver and to DTV
AUDIO on theTV back panel.
[] To utilize the benefits of a digital A/V re-
ceiver, connect your DTV receiver's digital
audio out to a digital input on your digital
A/V receiver.
[] The H and V connections on the TV back
panel are not used when connecting com-
ponent video (Y/Pr/Pb).
TV back panel
Figure 2. Connecting the DTV receiver with com-
ponent video connections.
SALE on Projector Bulbs at www.BulbAmerica.com
take additional 5% Off with coupon code 5PDF