Mixlinker APRUS II User manual

TM
APRUS II
Operation Manual
Mixlinker Networks (Shenzhen) Inc.

Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1)Reorient or relocate the receiving antenna.
2)Increase the separation between the equipment and receiver.
3)Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4)Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
To comply with FCC RF exposure compliance requirements,this grant isapplicable to only
mobile configurations. The antennas used for this transmittermust be installed to provide a
separation distance of at least 20 cm from allpersons and must not be co-located or
operating in conjunction with any otherantenna or transmitter.

Contents
I. Introduction------------------------------------------------------------- 01
II. Nomenclature --------------------------------------------------------- 02
III. Packing List------------------------------------------------------------03
IV. Specification ----------------------------------------------------------03
V.Interfaces---------------------------------------------------------------- 04
VI. Indicators -------------------------------------------------------------- 08
VII. Connections---------------------------------------------------------- 09
VIII. Installation----------------------------------------------------------- 10
IX.FCC Warnning --------------------------------------------------------- 12

I. Introduction
Welcome to use the Advanced Programmable Remote Utility
Server (APRUS II) of Mixlinker Network (Shenzhen) Inc. (herafter
referred to as Mixlinker).
APRUS is an advanced programmable Internet ofThings
adaptor for industrial equipment developed by Mixlinker.
APRUS II is the second generation product of Mixlinker, and
will be referred to as APRUS II.
APRUS II is an intermediate adapter developed to address
theneeds of traditional equipment for IoT. Adaptors are used
to establish data communication with equipment (controller)
without making changes to equipment, by way of adapting, to
send the operation status and data to IoT platform, so as to
make the right judgement and take right action to reduce the
malfunction of equipment, lowing operation cost. This manual
briefly introduces APRUS II to customers, and provide
help to customers for using the product.
01

Product Info
Mi x linke r Adva nce d
Progra mm ab le R em ot e
Ut ili t y Se rv e r ( APRU S II)
4
GPS Modules
2
M od ule w i th GP S
A 2 - 4207 - B
Communication Modules
2 G C o mmunic at i o n M od ule
Power Input
AC/DC 24V Input
Interfaces
0
CAN,RS485-1,RS485-2
02
II. N o mencl at u r e

III. Packaging List
APRUS II (1) GPS Antenna (1) - optional
GSM Antenna (1)
Micro SIM Card (1)
IV. Specification
Item
Settings/Configurations
GPRS Antenna Interface
Standard SMA Interface
(Female Connector)
Wireless Network
GPRS 2G Network
(Not Supporting CDMA)
Input Voltage
AC/DC9~24V
Maximum Power Dissipation
3W
Average Power Dissipation
1W
Operating Temperature
-20° C to +45°C
Storage Temperature
-40° C to +100°C
Operating Humidity
45%-80%
Storage Humidity
30%-90%
Weight
210g
Dimension
146*97*49mm
RS485 Interface
Isolated
USB Interface
Mini USB Female Connector
03

V.Interfaces
ETH
GPS GSM
APRUS II (Interfaces on Top)
1 2 3
No.
Symbol
Definition
1
GPS
GPS Antenna Interface
2
GSM
GSM Antenna Interface
3
ETH
Ethernet Interface (Optional)
APRUS II (Interface on Left Side)
1
No.
Symbol
Definition
1
EXT
Extended Interface
04

V. Interfaces
APRUS II (Interfaces on Right Side
1 2
No.
Symbol
Definition
1
SIM
Micro SIM Card Slot
2
USB Interface
APRUS II, when using Micro SIM
card, please insert the card“chip
down and notched edge facing
outward”
05
SIM

V. Interfaces
APRUS II (Interfaces on the Bottom)
Note：
When choosing adapters of
one RS485 and one RS232, the
default for 3 and 4 is RS232,
and 6 and 7 is RS485
1 3 5 7 9 11
2 4 6 8 10
No.
Item
Indicator
1
CAN-L
CAN-L
2
CAN-H
CAN-H
3
TX/A-1
RS232_TX1/RS485_A1
4
RX/B-1
RS232_RX1/RS485_B1
5
GND
Shared Ground
6
TX/A-2
RS485_A2
7
RX/B-2
RS485_B2
8
GND
Shared Ground
9
SGND
Shell Ground
10
POW +
Polarity - Positive
11
POW -
Polarity - Negative
06
CAN-L
CAN-H
TX/A-1
RX/B-1
GND
TX/A-2
RX/B-2
GND
SGND
POW +
POW -

V. Interfaces
5 6
APRUS II (Front)
1
GSM SVR GPS PWR
RST
SOS
4
2 3
No.
Item
Indicator
1
GSM
GSM Indicator Light
2
SVR
SVR Indicator Light
3
GPS
GPS Indicator Light
4
PWR
Power Indicator Light
5
RST
Reset Button
6
SOS
SOS Button
07
Note:
Press SOS to trigger a “short press event”. Press and hold for 3 seconds to
trigger a “long press event”. Event will be handled by FIDIS, and may be
customized according to customers'needs.

VI. Indicators
Note: During electrical initialization and self-testing on adaptors, the
SVR, GPS and PWR indicators will simultaneously be on for 500ms and
off for 500ms.
Status
Indicator
Normal
Abnormal
1
GSM Status
Indicator
1. Upon successful logon of SIM card,
indicator shall be on at the interval
of 3000ms, for 64ms each time.
2. Upon the connection of GPRS and
module is workingnormally,
indicator will be on at the interval
of 300ms, for 64ms each time.
1. When SIM card is not registered
online, indicator shall be on at the
interval of 800ms, for 64ms each
time.
2. When module is not poweredon,
indicator shall be off.
2
SVR Status
Indicator
1. When GARDSis correctly
connected, indicator shallbe
on at the interval of 2s, for 60ms
each time.
1. When thereis no signal for SIM card,
or not connected to antenna,
indicator shall flash three times every
2s, for 60mseach flashing.
2. Failure of SIM card registrationwith
vendor, indicator shall flashthree
times every 2s, for 60ms each flashing.
3. When SIM cardis not activated,
indicator shall flash three times every
2s, for 60mseach flashing.
4. When SIM cardis not inserted
securely, or the slot on adaptor
becomesloose,or slot power source
is not compatiblewithSIMcard,
indicator shallflash two times every
2s, for 60mseach flashing.
5. When adaptor is not connectedto
server, indicator shall flash four times
every 2s, for 60ms each flashing.
3
GPS Status
Indicator
1. When GPS signal is normal, indicator
shallbe on two times every 2s, for
60ms eachtime.
1. When GPS signal is not normal,
indicator shall be off.
4
Power Status
Indicator
1. When power is connected normally,
indicator will be onconstantly.
2. When MCU is being upgraded,
indicator shall flash quickly at the
interval of2s.
1. When power is not connected
normally, indicator will be off.
08

VII. Connections
PLC
CAN Interfac
CAN-L
CAN-H
RS232 Interfac
RX/B-1
TX/A-1
GND
RS485 Interfac
TX/A-2
RX/B-2
GND
CAN Interfac
Rs232 Interfac
RS485 Interfac
CAN-L
CAN-H
TX/A-1
RX/B-1
GND
TX/A-2
RX/B-2
GND
CAN-L
CAN-H
TX/A-1
RX/B-1
GND
TX/A-2
RX/B-2
GND
SGND
Power Interface Power Interface
SGND
POW +
POW -
Note:
SGND
POW +
POW -
POW +
POW -
APRUS II
1.This wiring diagram demonstrates an adaptor
with a grouping of RS485 and RS232. For
adaptors with two groups of RS485, please
refer to the above diagram for the wiring of
RS485. Please follow the correct wiring.
Otherwise data will not be collected from
equipment.
2.Please connect the
antennas of GPS and
GSM correctly.
Otherwise equipment
shall not pick up signal
and GPS will not locate
the position.
09
GPS Antenna Interface
GSM Antenna Interface
Ethernet Interface (Optional)
ETH
GPS GSM

VIII. Installation
There are two methods for APRUS II installation: 1. With screws,
screw size: M4.5, as shown below:
10

VIII. Installation
2. Installation with rails, the size of rail: 35mm, as shown below:
Install stopper
Rail
Step 1：
Raise the stopper
on the adaptor.
Note:
1. For the safety of you
and the equipment
and adaptor, please
power off the
equipment prior to
performing the
installation.
2. Prior to installation,
please insert SIM
card into slot and
complete all the
wiring correctly on
adaptor.
Step 2：
Install the adaptor onto
the rail. (Please secure
the bottom rail groove
onto the rail bottom first.)
Step 3：
Push down the stopper.
11
35mm

Mixlinker Networks (Shenzhen) Inc.
：3/F Spring Tower, Meisheng Creative
Valley, 10 Longchang Rd. Shenzhen
：0755-23740592
：www.mixlinker.com
V1.0