MJX F39 Shuttle User manual

лчиттничюнльтцию.
глтчн.Бзвыдны
www.sotmarket.ru
дбняинфмциятв,
тзывы,бзыиы
Инструкция для
MJX F39 Shuttle
Перейти в карточку товара
8 800 775 98 98

ITEM NO.F39/F639

1
Introduction
Thank you for purchasing this product. Please read this manual carefully
before use and retain it for future reference.
Technical parameter of the helicopter
Gross Weight: about 665g
Motor: #370
Tail Rotor Diameter: 148MM
Battery: Li-polymer 7.4V
Fuselage Length:810MM
Overall height: 315MM
Gear Ratio: 14:1 Charging Time: about 3 hours
Main Rotor Diameter: 515MM
Coaxial-rotor design, built-in gyro and negative rotation of rotors
are used to increase the helicopter’s stability and operability. It is
the best choice for beginner.
Aluminum fuselage design and innovative appearance make the
helicopter full of attraction.
By using of the 2.4G auto connection technology, scores of helicopters
can be played at the same time with high stability.
Microcomputer control LCD remote controller brings more operation
interesting for player. By adjusting the parameter, user can randomly
regulate the helicopter’s left/right turning speed, left/right sideward
flight speed and the speed of moving forward /backward.
Forward/backward and sideward flight controlled by swashplate, the
helicopter is strong enough for outdoor free flight.
Equipped with screw servo,F39/F639 has the characteristics of light
weight, easy operation and rapid response.
Safety Guidelines
This product is not a toy. It is not applicable for children who are under
14 years old.
Please read this instruction manual carefully before playing and operate
the product according to the manual.
The users are in full charge of proper operating the helicopter. The
manufacturer and dealers disclaim all responsibility for the damage
caused by misuse.
Keep the small accessories away from the kids to avoid accident.
Keep batteries away from fire or high temperature environment.
When flying the helicopter, keep it 1~2 meters away from user or others
to avoid injury due to collision.
Not to decompose or modify the product which may cause malfunction
or accident.
Fly the helicopter within your eye vision for easy and safety control.
Need adult supervision when this helicopter is being played by children.
Only batteries of the same or equivalent type as recommended are to be
used.
Insert batteries with correct polarity.
Non rechargeable batteries are not to be charged; the transmitter need
4XAA batteries for work.
Do not mix old and new batteries.

2
The LCD Remote controller
Remote Controller
(Transmitter)
Microcomputer control LCD remote controller ,with the 2.4G auto
connection technology, many helicopters can be operated
simultaneously with high stability.
Control the actions of upward,downward,forward, backward,leftward,
rightward,turning left and turning right of the helicopter.
Throttle control stick can be freely switched according to player's
willingness.
1
2
Product/spare parts included in this packaging
Description
Left stick
Right stick
STICK MOD2:upward/downward,leftward/rightward;
STICK MOD4:upward/downward,turn left/turn right;
STICK MOD1:forward/backward,turn left/turn right;
STICK MOD3:forward/backward,leftward/rightward.
STICK MOD1: upward/downward,leftward/rightward;
STICK MOD3: upward/downward, turn left/turn right;
STICK MOD2: forward/backward,turn left/turn right;
STICK MOD4: forward/backward,leftward/rightward.
3 Trimmer A
In stick Mod 2 and 4, this button is null.
In stick Mod 1and 3, it helps to tune the helicoper's
forward and backward flight.
Helicopter 1
1
2
1
1
Remote controller
Rotor blade
Manual
Adaptor
Qty(pc) Description Qty(pc)
13
PUSH
EXIT/
LIGHT
MENU/
OK
POWER
1. Left stick
12. Throttle changing
button (Left)
13. Throttle changing
button (Right)
14. Exit
7. Power switch
8. Antenna
9. Power indicator
11. Camera Switch
2. Right stick
3. Trimmer A
4. Trimmer B
5. Trimmer C
10. Menu/OK15. LCD screen
6. Trimmer D
No. Function switch Function description
Main features of the remote controller
Sketch and function switches of the remote controller

3
4
In stick Mod 2 and 3, it helps to tune the helicopter's
sideward flight.
In stick Mod 1 and 4,it helps to tune the helicopter's
left and right direction turning speed.
In stick Mod 2 and 3, it helps to tune the helicopter's
left and right direction turning speed.
In stick Mod 1 and 4,it helps to tune the helicopter's
sideward flight.
In stick Mod 1 and 3, this button is null.
In stick Mod 2 and 4, it helps to tune the helicoper's forward
and backward flight.
It controls the power source of the transmitter.Slide
the power switch to the “ON” position, the transmitter
is powered on; slide the power switch to the “OFF”
position, the transmitter is powered off.
No. Function switch Function description
Trimmer B
5 Trimmer C
6 Trimmer D
7
8
Power switch
Antenna
9Power
indicator
Transmits wireless signal.
The indicator light keeps blinking slowly: the transmitter
is not activated.
The indicator light keeps flashing rapidly: the transmitter
is sending out connectional signal to the helicopter.
The indicator light keeps on without blinking: the
transmitter is ready for controlling the flight.
10 Menu/OK
Press this button to enter into the parameter setting
menu or store the setting after parameter adjustment.
Turn clockwise /counter clockwise to select the
desired menu or increase/ decrease the value when
adjusting the parameter.
11 Camera Switch Turn on/off the camera of the helicopter.
12/13
Throttle
changing button
Slide down or slide up the 2 buttons at the same time
to select the throttle control stick
14 Exit In the start-up interface, After enter into the menu, press this
switch to exit from the menu or cancel the setting.
Remote controller’s parameter setting
Select the throttle control stick
Activate the LCD remote controller
There is 1 throttle button on either side of the remote controller.
Slide both of the 2 buttons to "R", the right stick is the throttle control stick.
Slide both of the 2 buttons to "L", the left stick is the throttle control stick.
Tip: both of the 2 buttons should be either on the position of "R" or "L",
otherwise, the remote controller can not be activated.
Slide the power switch to "ON" position after throttle control stick selection
is done.To activate the remote controller, slowly push up the throttle control

4
After the remote controller is activated, press Menu/OK button to enter
into the function menu. Turn clockwise or counter clockwise to select the
desired menu and enter into the parameter setting interface to set the
parameters.
Enter into the function menu and find the blinking ELEV icon by turning
clockwise or counterclockwise of the MENU/OK button.Press MENU/OK
button to stop the blinking of ELEV icon and enter into the Forward/
backward speed setting interface.Turn clockwise of the MENU/OK button
to increase the forward/backward flight speed and turn counter clockwise
of the MENU/OK button to decrease the forward/backward flight speed.
Press MENU/OK button to store the setting or Press EXIT/LIGHT button to
cancel the setting.
POWER
POWER
Pic1 Pic2
Pic
4.7V
00%
STICK MOD 2
AILE
ELEV RESET
RUDD THRO
Battery power icon
Reset Mod select
channel data
icon
leftward/
rightward
speed gauge
left/right
turning extent
gauge
trim icon trim icon
channel icon
forward/
backward
speed gauge
Enter into the function menu and find the blinking RUDD icon by turning
AILE: Leftward/rightward speed setting
ELEV: Forward/backward speed setting
RUDD: Left/right turning extent setting
When enter into the function menu, the icon AILE keeps blinking; Press
MENU/OK to enter into the Leftward/rightward flight speed setting interface.
At this time, the AILE icon stops blinking.Turn clockwise of the MENU/OK
button to increase the leftward/rightward flight speed and turn counter
clockwise of the MENU/OK button to decrease the leftward/rightward flight
speed.Press MENU/OK button to store the setting or Press EXIT/LIGHT
button to cancel the setting.
stick to the top and then push it down to the bottom. The remote controller
is activated once a beep sound is heard. Then, the indicator light keeps
flashing while the remote controller is sending out connectional signal. It
takes about 10 seconds to finish the signal transmission process. After
signal transmission is completed, the indicator light keeps constant "on”.
User can turn either the left stick or the right stick to skip the signal
transmission process and enter into the start-up interface directly.

5
There are 4 flight modes available for selection: Stick Mod 1 (Pic.3)
Stick Mod 2 (Pic.4) Stick Mod 3 (Pic.5) Stick Mod 4 (Pic.6)
Enter into the function menu and find the blinking STICK MOD icon by
turning clockwise or counterclockwise of the MENU/OK button.Press
MENU/OK button to stop the blinking of STICK MOD icon and enter into
the Stick Mode selection interface.
When the left stick controls the throttle, the digit of 2 and 4 will be showed
on the screen, Turn clockwise or counterclockwise of the MENU/OK
button to select either of the modes; Press MENU/OK button to store the
setting or Press EXIT/LIGHT button to cancel the setting.
When the right stick controls the throttle, the digit of 1 and 3 will be
showed on the screen, Turn clockwise or counterclockwise of the
MENU/OK button to select either of the modes; Press MENU/OK button to
store the setting or Press EXIT/LIGHT button to cancel the setting.
STICK MOD:1 STICK MOD:2
POWER
󳬅󳬅
Pic.3 Pic.4
Forward /
Backward
control
Forward /
Backward
control
Forward /
Backward
control
Forward /
Backward
control
Throttle
control
Throttle
control
Throttle
control
Throttle
control
Left/Right
turning
control
Left/Right
turning
control
Left/Right
turning
control
Left/Right
turning
control
Leftward/
Rightward
control
Leftward/
Rightward
control
Leftward/
Rightward
control
Leftward/
Rightward
control
STICK MOD:3 STICK MOD:4
󳬅󳬅
PUSH
EXIT/
LIGHT
MENU/
OK
Pic.5 Pic.6
Stick Mode Selection
RESET
Enter into the function menu and find the blinking RESET icon by
turning clockwise or counterclockwise of the MENU/OK button.Press
MENU/OK button to stop the blinking of RESET icon and enter into the
RESET interface.At this time, there will be "Yes" and "No" for selection,
Turn clockwise or counterclockwise of the MENU/OK button to select
"YES";Press MENU/OK button to restore all the parameters to factory
default setting.
clockwise or counterclockwise of the MENU/OK button.Press MENU/OK
button to stop the blinking of RUDD icon and enter into the left/right
turning speed setting interface.Turn clockwise of the MENU/OK button to
increase the left/right turning speed and turn counter clockwise of the
MENU/OK button to decrease the left/right turning speed.Press MENU/OK
button to store the setting or Press EXIT/LIGHT button to cancel the setting.

6
The helicopter
When the power of the transmitter is weak, the battery power icon will
keep blinking and send out beep sound to remind user to change new
battery.
connector stabilizer bar
servo
rotor blade
searchlight
power socket battery connector
landing gear
camera
How to charge the helicopter
Transmitter battery low power prompt
split charging device
all-in-one charging device
How to charge the helicopter by split charging device.
To meet the different demands from different customers worldwide,
two different charging devices have been designed for charging. One is
split charging device (1 piece charger +1 piece charge controller), the
other one is all-in-one charging device (one charger only)The product is
included with either of the two charging devices. User should check the
package to confirm which charging device is included before reading the
charging method.
How to charge the helicopter by all-in-one charging device.
Turn off the helicopter.
Unplug the battery cable from the helicopter, then, insert the plug of the
battery cable into the port of the charger (matching the plug to the port)
to start charging.
Once charging is proceeding, red light is on. When charging is finished,
the red light will turn into green light.
Full charge takes about 3 hours.
Turn off the helicopter; unplug the battery cable from the helicopter.
Insert the plug of the battery cable into the quadrate port of the charge
controller (matching the plug to the port)
Insert the plug of the charger cable into the circular port of the charge
controller, then, connect the plug of the charger to AC power outlet to
start charging.
Once charging is proceeding, the red power light of the charge controller
is on. When charging is finished, both the red light and green light of the
charge controller are on.
Full charge takes about 3 hours.

7
Insert the battery plug into the helicopter battery socket located at
the right side of the helicopter, then, the indicator light of the helicopter
will keep flashing rapidly, set the helicopter down to a platform.
Slide the power switch to “ON” position. To activate the remote
controller,slowly push up the throttle stick to the top and then push
it down to the bottom. The remote controller is activated once you hear
a beep sound.Then, the indicator light flashes rapidly while the remote
controller is sending out connectional signal.
When the whole auto signal connection process is finished, push up the
throttle stick slowly and the helicopter takes off.
User may push either of the control sticks to skip the auto signal
connection process once the helicopter finished signal connection.
Set the connection one by one. Otherwise, it may not be connected.
Once the transmitter is turned off, the connection procedure must be
repeated to operate the helicopter.
Please pull out the battery plug from the helicopter battery socket.
Operational Tips
Preparation for flight
Flight adjustment
1.Adjusting the swash plate
Insert the battery plug into the power socket of the helicopter and set
the helicopter down to a platform. When the transmitter and helicopter
finish the auto signal connection process, the indicator light will keep
“ON” without blinking.Users can get a longer sound when the trimmer of
forward/backward is pushed to the middle position, at this time,please
check the swash plate and if it is not keep in horizontal, users can
adjusting the length of the servo connector, until the swash
plate remains horizontal.

8
Pic7 Pic8
Swash
Parallel
Platform of the swash
Extension line of the helicopter
Servo
connector
Trimmer Functions
If the helicopter keeps moving forward/backward even there is no control
signal given, users may adjust the elevator trim to keep the helicopter
balanced.
STICK MOD 1 or 3:
If the helicopter keeps moving
backward, push up Trimmer A
until it gains balance.
If the helicopter keeps moving
forward, push down Trimmer A
until it gains balance.
STICK MOD 2 or 4:
If the helicopter keeps moving
backward, push up Trimmer D
until it gains balance.
If the helicopter keeps moving
forward, push down Trimmer D
until it gains balance.
STICK MOD 2 or 3:
If the helicopter keeps moving leftward/rightward even there is no control
signal given, users may adjust the aileron trim to keep the helicopter
balanced.
If the helicopter keeps moving
leftward, turn right of Trimmer B
until it gains balance.

9
If the helicopter keeps moving
righttward, turn left of Trimmer B
until it gains balance.
STICK MOD 1 or 4:
If the helicopter keeps moving
leftward, turn right of Trimmer C
until it gains balance.
If the helicopter keeps moving
righttward, turn left of Trimmer C
until it gains balance.
STICK MOD 1 or 4:
If the helicopter keeps spinning even there is no control signal given,
users may adjust the rudder trim to keep the helicopter balanced.
If the helicopter keeps spinning
counterclockwise in the air,turn
right of Trimmer B until it gains
balance.
If the helicopter keeps spinning
clockwise in the air,turn left of
Trimmer B until it gains balance.
STICK MOD 2 or 3:
If the helicopter keeps spinning
counterclockwise in the air,turn
right of Trimmer C until it gains
balance.
If the helicopter keeps spinning
clockwise in the air,turn left of
Trimmer C until it gains balance.

10
Operating
Video function and videography device
TF memory card
Upward
Downward
Turn left
Turn right
Forward
Push up the throttle control stick, the
rotation speed of the mains rotors are
increasing and the helicopter ascends
accordingly.
Push down the throttle control stick,
the rotation speed of the mains rotors
are decreasing and the helicopter
descends accordingly.
Turn the left/right turning control stick
to the left,the helicopter will left.
Turn the left/right turning control stick
to the right,the helicopter will right.
When the helicopter is flying, push up
the forward/backward control stick, the
helicopter will move forward.
Backward
When the helicopter is flying, push
down the forward/backward control
stick, the helicopter will move backward.
Leftward flight
Turn the sideward flight control stick to
the left side,the helicopter will fly
leftward.
Rightward flight
Turn the sideward flight control stick to
the right side,the helicopter will fly
rightward.
If installed the C4001 videography device(should be ordered separately
from MJX), the helicopter has the videography function.
card reader videography module
Videography device

11
Trouble shooting
When the helicopter is finished signal connection and is not under
shooting condition, the indicator light of the videography module keeps
constant "on".When press the shooting switch on the remote controller,
it begins shooting and the indicator light turns from constant "on" to
flashing, press the shooting switch again, shooting will stop.
After shooting is finished, take out the TF memory card from the
videography module and insert it into the card reader(Pic. 12), then,
insert the card reader into the USB interface of the computer to watch
the video.
Pic9 Pic10 Pic11 Pic12
Problem
No reaction
from the
helicopter
1.The helicopter is underpowered. 1.Get the battery of the helicopter charged
2.The indicator light of the helicopter
flashing rapidly, and the gyo is in
the testing statement
2.Set the helicopter down to a platform, until the
indicator light turn to constant ”ON” without
blinking.
3.Repeating the connection procedure.
3.the helicopter and the transmitter
is out of radio connection
Reason Solution
Video control
Insert the TF memory card into the videography module.(Pic9)
Fix the videography module onto the bottom of the helicopter by
screws.(Pic10)
Open the helicopter nose and insert the plug of the videography module
into the video control socket, then, reinstall the helicopter nose.(Pic11)
How to install the videography device
TIPS
To stop shooting, please press the shooting switch on the remote controller.
Directly unplug the battery cable or take out the TF memory card from the
videography module will result in loss of the video data.
To avoid helicopter crash,please do not insert or take out the TF memory
card from the videography module,when the circuit is on. TF memory card
should be installed before circuit is on and take out after shooting switch is
turned off.
When crash occurs,turn off the helicopter and then turn on the power to
recover normal working.

лтззлюбым
дбнымбм
глтчня
лжбдджи
Дтвззв
вии
фмлнидит
нлнз2минты
мнииДтвилтвинитзывыцииииди
MJX F39 Shuttle
Описание Характеристики