ML Accessories LANTSS Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
LANTSS / LANTBK

These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
LANTSS / LANTBK
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class I and must be earthed
• This product is IP23 rated
SAFETY
• Provide power to the point of installation. Suitable IP rated junction boxes should be used where required
• Remove the 2 baseplate screws on either side of the fitting
• Using the baseplate as a template, mark the location of the fixing holes, and drill the holes ensuring not to
infringe with any joists, gas/water pipes or electrical cables
• Feed cable through the cable entry grommet and secure baseplate to chosen surface
• Connect Live (brown), Neutral (blue) and Earth (green/yellow) to the 3-way terminal block in the base of the
fitting (see Fig. 1)
INSTALLATION

Fig. 1
LANTSS / LANTBK
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
LANTSS / LANTBK
SAFETY
•Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
•Please isolate mains prior to installation/maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
•Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
•This product is Class I and requires an earth
•This product is IP23 rated
INSTALLATION
•Provide power to the point of installation. Suitable IP rated junction boxes should be used where required
•Remove the 2 base plate screws on either side of the fitting
•Using the base plate as a template, mark the location of the fixing holes, and drill the holes ensuring not to
infringe with any joists, gas/water pipes or electrical cables
•Feed cable through the cable entry grommet and secure base plate to chosen surface
•Connect Live (brown), Neutral (blue) and Earth (green/yellow) to the 3-way terminal block in the base of the
fitting (see Fig 1)
Fig 1
•Line up the fitting with the base plate and fasten down the 2 base plate screws
•Install an E27 lamp into the fitting (not supplied) ensuring not to exceed the 40W maximum rating
•Reposition diffuser back into place
•Switch on power and test for correct operation
Live (brown)
Neutral (blue)
Earth (green/yellow)
NEL
• Line up the fitting with the baseplate and fasten down the 2 baseplate screws
• Install an E27 lamp into the fitting (not supplied) ensuring not to exceed the 40W maximum rating
• Reposition diffuser back into place
• Switch on power and test for correct operation
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is not suitable for installation in or near a coastal or marine environment.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
GENERAL

DCJUL21_V2
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
02
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
This product has a warranty of 2 years from date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
WARRANTY