MMATS Professional Audio D600.2 User manual

MMATS
Professional Audio
D600.2
Owner’s Guide
MMATS Professional Audio
867 West 13th Court
Riviera Beach, Fl. 33404
http://www.mmatsproaudio.com

CLASS D TECHNOLOGY
MMATS Professional Audio is the industry leader in ultra-efficient
Class D audio technology for 12 volt audio.
Your D600.2 amplifier is engineered using the best technology we
have at MMATS.
Surface mount technology
Large geometry power MOSFETs
Leading edge pulse width modulation design
D600.2 amplifiers are the perfect match for producing bass from
large speakers in an automotive environment. Since most of the
acoustic energy needed to produce full range audio is in the bass
frequencies, it makes sense to dedicate your system’s most
powerful amplifiers to this task. Also, an automobile has a limited
amount of energy available in its charging system to produce these
power hungry bass frequencies. Therefore, an efficient amplifier that
doesn’t waste energy as heat would be desirable.
Class D amplifiers are switching amps. Instead of producing power
continuously like a traditional Class A or AB amplifier, a Class D
amplifier switches on and off thousands of times a second and
doesn’t waste energy (as heat) by being on when not needed.
Comparison of technologies at full power:
Class AB 500W amp at 50% efficiency will draw 1000W off the
charging system.
1000W / 12.5V = 80 Amp draw
MMATS Class D 500W amp at 72% efficiency will draw 694W off
the charging system.
694W / 12.5V = 56 Amp draw
1000W - 694W = 306W wasted as heat that should be driving
your speakers!
SPECIFICATIONS
RMS Power at 13.8V
350W into 4 ohms with less than .1% THD+N
500W into 2 ohms with less than .1% THD+N
THD+N @ rated power: 0.05%
Frequency Response: <10 to 225Hz
Bass Boost: Variable 12db @ 45Hz
Lowpass Filter: Variable 12db, 70 to 200Hz
Dimensions (LxWxH): 8” x 9.25” x 2.25”
WARRANTY
3 years from date of manufacture when installed by an authorized
MMATS Professional Audio dealer. Proof of purchase required.
Non-transferable
**Manufacturers warranty is void on product purchased over
the internet.

SUGGESTED HOOKUP
D600.2
SPEAKER
OUTPUTS
+ - + -
+ - + -
4 OHM 4 OHM
HOOKUP INTO TWO 4 OHM WOOFERS
D600.2
SPEAKER
OUTPUTS
+ - + -
- +
4 OHM 4 OHM
+ -
HOOKUP INTO ONE DUAL VOICE COIL
(4 OHMS PER COIL) WOOFER
FEATURES
 Ultra- Efficient Class D Audio Output Stage
 Regulated Pulse-Width-Modulated Power Supply
 High Capacity Heat Sink
 Adjustable 12db Low Pass Filter
 Adjustable 45Hz Bass Boost
 Low Level and Speaker Level Inputs
 1% Surface Mount Components
 Computer Optimized Transformer
 Large Geometry Power MOSFETs
 Overload and Thermal Protection
CONTROLS AND CONNECTORS
1. Positive Power Terminal - This is the power feed from the
positive (+) terminal of the car’s battery. Use 8 gauge cable
and good quality terminals when routing this connection.
Tighten the connections well to prevent power loss due bad
contact. Route the power cable away from the RCA and
speaker cables
2. Fuses - Replace these fuses with only with the same type
and value. These fuses only protect the amplifier. An
additional inline fuse should be added at the battery to
protect against a short in the main power cable to the
amplifier.
3. Ground Terminal - For optimum performance, an 8 gauge
cable and good quality connectors should attach the this
terminal to the battery’s negative (-) terminal.
4. Remote Terminal - The amplifier will turn on when 12 volts
is applied to this terminal. This 12 volt signal is usually taken
from the Power Antenna or Remote wire coming from the
source unit.

CONTROLS AND CONNECTORS
CONTINUED
5. Speaker Terminals - Connect to speakers using at least 14
gauge speaker wire. Note that there are two Sp+ and SP-
terminals that are internally wired in parallel to the + and -
output of the class D stage. These are provided for easier
connection of multiple speakers and should not be confused
with the traditional Left and Right stereo hookup of traditional
amplifiers. Running too low of a speaker impedance will
cause the amplifier to go into a fault condition.
6. 45Hz Bass Boost – This control will add up to 12db of boost
at 45Hz to give the music more ‘kick’. Be careful! This added
boost could run your speakers into clipping when listening to
bass intensive music.
7. Lowpass Filter – Butterworth 12db slope. This control sets
the 3db down point of your amplifier. Higher frequencies
beyond this setting are not heard from your speakers.
8. Gain – 20db of signal gain is available. This allows input
levels between 150mV and 2 volts for full output.
9. Inputs – Two RCA jacks are provided. Their signals are
added together inside the amplifier and the bass information
is extracted. Since they are summed together, it does not
matter which one is ‘Left’ or ‘Right’.
10. High level inputs – These are provided for use with head
units that do not have RCA outputs. Attach the appropriate
speaker outputs from the head unit to the terminals provided.
PANEL LAYOUT
Speaker Terminals
Lowpass Filter
45Hz Bass Boost
Gain
Inputs
High level inputs
Ground Terminal
Remote Terminal
Positive Power Terminal
Fuses