Mobile Power quickboost 2007 User manual

MobilePower, LLC. Bluffton, SC 29910
www. Mobilepower-us.com Office: (800) 708 - 8550
[e-mail]
[e-mail]
Sheet 1 of 12
Model No. 2007
QuickBoost
Instruction Manual

QuickBoost
8in ONE Multi-Purpose
Vehicle Jumpstart System
Model No. 2007
Sheet 2 of 12
Double Injection Casing with
Rubberized Protective
Bumper Guards
Air Compressor Rated at 260 psi
With 100 PSI Air Pressure Gauge
Foldable Handle For Vertical
And Horizontal Operation Modes
Air Valve Nozzle with 3
Adaptors for Inflatables
USB 5 Volt Output Port
with Protective Dust Cover
Reverse Jumpstart
Polarity Protection LED
12 Volt Vehicle Jumpstart
System with Heavy Duty
Cable and Clamps
Main Power Booster Clamps
ON/OFF Rotary Switch
Internal Battery Charge Level
Status Push Button
Air Compressor
ON/OFF Switch
LED Area Light
USB ON/OFF
Toggle Switch
LED Area Light ON/OFF
Toggle Switch

IMPORTANT INFORMATION
READ AND UNDERSTAND ALL WARNINGS AND THE ADVISORY NOTES INCLUDED IN THIS
MANUAL. FOLLOW INSTRUCTIONS PROVIDED BY YOUR VEHICLE MANUFACTURER AND MAN-
UFACTURER OF THE DEVICES INTENDED TO BE USED WITH THIS POWER SUPPLY.
MAKE CERTAIN THIS DEVICE IS FULLY CHARGED PRIOR TO FIRST USE.
WARNINGS
THIS PRODUCT CONTAINS A SEALED LEAD-ACID BATTERY AND MUST BE DISPOSED OF
PROPERLY. YOU MAY CONTACT YOUR LOCAL GOVERNMENT RECYCLING AUTHORITY FOR
APPROPRIATE DISPOSAL. FAILURE TO FOLLOW THE INSTRUCTIONS MAY CAUSE DAMAGE
TO THE PRODUCT AND OR PERSONAL INJURY.
ON
OFF
Internal Battery
Charging Port
Charging Indicator LED
12 Volt DC - 10A Accessory Port with Protective
Cover Vehicle Jumpstart System through
Cigarette Lighter Socket
USB Port with Protective Cover
Battery Charge Level
Status Push Button
Main Power Booster Clamps
ON/OFF Rotary Switch
Sheet 3 of 12
Model No. 2007
ON
OFF
U
S
B
S
W
I
T
C
H
USB ON/OFF
Toggle Switch

IMPORTANT ADVISORY NOTES
 Do not use with dry cell batteries. These batteries may burst and cause injury to person or damage
personal property.
 Do not attempt to face the battery being jumped. Stay away as far as possible from the battery when
making the final connection.
 DO NOT CONNECT TO or jump start a 6 or 24 Volt battery.
 If battery acid comes in contact with skin or eyes, rinse immediately with water for 20 minutes. Seek
medical attention if redness, irritation or pain is present.
 DO NOT smoke, use matches, lighters or an open flame near batteries.
 This products contains chemical substances including lead. Wash hands thoroughly after handling Lead
Acid Batteries.
 Never allow red (Positive) and black (Negative) clamps to come in contact with each other or
contact with metal object at the same time.
 To protect against electrical hazards, do not immerse charger, adapters, or unit in water or other liquid.
 Close supervision is necessary when working near children.
 Do not use unit for applications other than its intended use.
 Always connect the red (+) clamp to the positive battery terminal first. Connect black (-) clamp to the
negative battery terminal as final connection.
 Jumpstart vehicles in a well ventilated area only.
 Do not expose this unit to moisture and use it in extremely hot conditions.
 Monitor the pressure gauge during use. Be careful not to over-inflate objects.
 Never work alone with this product. Make sure that someone is available to give assistance if needed.
 Wear complete eye and clothing protection. Do not touch eyes while working near battery.
 Do not attempt to remove or replace the battery used in this device. When the battery has reached the
end of its useful lifetime, take the entire unit to a battery recycling facility.
 For proper and safe operation of the 12 Volt DC Power Accessory Port, do not place anything into it
except the plug of the accessory to be used.
 Remove metal, personal jewelry, such as: rings, bracelets, necklaces and watches, while working with a
lead acid battery. This can produce a short-circuit that may cause severe burns.
 Never charge or jump-start a frozen battery.
 Do not operate this device while wearing vinyl clothing. Static electricity may be generated when vinyl
clothing is rubbed.
 This product is not intended for use in the rain or temperatures above 150ºF.
 Use only the provided chargers, cables and clamps. Unauthorized parts may damage the unit.
 This product has no consumer serviceable parts except the replaceable fuses.
 Keep out of the reach of children.
 Keep battery terminals clean. Be careful to keep corrosion from coming in contact with eyes.
 Do not let the cords of this device or jumper clamps get wet.
 Prevent water to get into the unit housing. Water will damage the internal electronics board.
 This unit has a built-in lead acid battery. Although the QuickBoost arrives partially charged from the
factory, it MUST be fully charged before the first use.
 Recharge the QuickBoost after each use or every 2 months preventing the battery voltage to become
extremely low.
Sheet 4 of 12
Model No. 2007

FEATURES:
8 in One Multipurpose DC Power Supply with Instant Vehicle Jumpstart System. The unit provides: Air
Compressor with Pressure Air gauge - Heavy Duty Booster Cables with Insulated Clamps - Main Power
Booster Cables ON/OFF Switch - Reverse Polarity Protection - Internal Battery Charge Level Status
Indicator LED Bars - LED Area Light with ON/OFF Switch - 12 Volt DC Accessory plug with Charge/
Booster Cable through vehicle 12 Volt DC cigarette lighter socket - USB power port with Protective
Cover - Air Nozzle Adaptors for most Inflatables Foldable Handle for Vertical and Horizontal Operation
Modes - Double Injection Casing with Rubberized Protective Bumper Guards.
Includes: 110V AC Charger , 12V DC Charger and Dual 12VDC Plug Booster Cable.
SPECIFICATIONS:
 BUILT-IN 12V 10AH RECHARGEABLE LEAD ACID BATTERY.
 300 CRANKING AMPS - 600 PEAK AMPS.
 12 VDC 10 AMP. RATED WITH PROTECTIVE PORT COVER
 USB 5 VOLT - 500 mA OUTPUT PORT WITH PROTECTIVE PORT COVER .
 260 PSI AIR COMPRESSOR WITH 100 PSI AIR PRESSURE GAUGE.
CHARGING INSTRUCTIONS:
CAUTIONS
 Prior to charge this device, read and understand all the related instruction indicated below.
Fully charge the unit when the Battery Status Indicator displays two bars. This product may
arrive partially charged from the factory. It is highly recommended to fully charge the
QuickBoost after purchase and before using for the first time.
 Make certain that all ON/OFF Power Switches are set in the OFF position.
 Do not charge the QuickBoost Power Supply near flammable material, open flame or any
location which accumulate flammable fumes.
 Make certain the electrical outlet located in a potentially wet or moist area that is to be used
to charge this device, is protected by a Ground Fault Circuit Interrupter (GFCI).
 Make sure that both booster clamps are securely placed in their designated storage
compartments when not in use and during the charging period.
CHARGE THIS PRODUCT IMMEDIATELY AFTER PURCHASE. RECHARGE AFTER EACH USE
AND EVERY TWO MONTHS.
A. AC Charging At Home with 110 Volt Charger
1. Keep the Main Power Booster Clamps ON/OFF Switch in OFF position while charging.
2. Insert the AC charger round plug into the QuickBoost Charging Port.
3. Connect the 110 Volt AC Charger into the 110 Volt AC home receptacle.
4. Fully charge the QuickBoost according to the following schedules:
First time charge: 18 hours
Recharge and subsequent charge: 6 to 8 hours
5. Unplug the AC charger from the 110 Volt receptacle first and then remove the round plug from the
QuickBoost Charging Port.
B. DC Charging In Your Vehicle with 12 Volt Charger
1. Keep the Main Power Booster Clamps ON/OFF Switch in OFF position while charging.
2. Insert the 12 Volt DC Charger round Plug into the QuickBoost Charging Port.
3. Connect the 12 Volt DC Charger Plug into the vehicle cigarette lighter or 12 Volt accessory port.
4. Fully charge the unit internal battery for 6 to 8 hours while the vehicle engine is running.
5. Unplug the DC charger from the vehicle cigarette lighter or 12 Volt accessory port first and then
remove the round plug from the QuickBoost Charging Port.
Model No. 2007
Sheet 5 of 12

INTERNAL BATTERY CHARGE LEVEL:
Battery Charge
Level
Battery Charge Level
Status Push Button
 Press and hold the Battery Charge Level Status
Push Button to determine the unit internal battery
charge level prior to each use.
 The battery Charge Level bars illuminate
indicating the Status of the battery Charge Level.
Sheet 6 of 12
Model No. 2007
FULL
100%
Charge
Level
75%
Charge
Level
50%
Charge
Level
Low
Charge
Level
LED Area Light ON/OFF
Toggle Switch
LED Area Light
LED Area Light:
LED Area Light: Press the end of
the toggle switch marked to turn on
the Area Light.
ON
OFF
Main Booster Power Switch
Main Booster Power Switch:
To turn ON Power to the Clamps: Turn the Main
Booster Power Switch quarter turn clockwise to turn
ON power to the Booster Clamps.
To turn OFF Power to the Clamps: Turn the Main
Booster Power Switch quarter turn counter-clockwise
to turn OFF power to the Booster Clamps.

AIR COMPRESSOR OPERATING INSTRUCTIONS:
CAUTIONS
 Do not operate the Air Compressor more than 10 Minutes continuously. Allow the
compressor to cool down for 10 to 15 minutes between each continuous operation.
 Review the products to be inflated for manufacturer’s recommended maximum inflation
pressure. Most tires are recommended to be inflated between 27 to 38 PSI.
 Always check the air inflation pressure with a separate and reliable pressure gauge during
and after inflation.
A. TO INFLATE TIRES:
1. The Air Hose Compartment is located on the bottom of the unit. Access to the Air Hose Nozzle and
pull out the air hose. Make sure that the Nozzle Locking Lever is in the UP position.
2. Remove the valve cap from the tire valve stem.
3. Attach the compressor air valve nozzle onto the tire air valve stem and push down the air valve
nozzle as far as it travels. Make certain it is seated properly.
4. Press down the Nozzle Locking Lever all the way down to securely lock the tire air valve stem.
IMPORTANT: If the tire is completely deflated, raise the vehicle by utilizing a recommended rated
lifting device and jack stand before inflating the tire.
5. Turn the compressor switch located on the side panel of the QuickBoost to ON position.
6. Monitor the pressure on the compressor Air Pressure Gauge while inflating.
7. Turn OFF the compressor when the desired tire air pressure is reached.
8. Disconnect the air hose nozzle from the tire air valve stem by lifting Nozzle Locking Lever to the UP
position.
9. Replace the tire valve cap onto the tire valve stem.
10. Stow the air hose into the Compressor Air Hose Compartment.
B. TO INFLATE BALLS/AIR MATTRESSES/RUBBER RAFTS:
1. The Air Hose Compartment is located on the bottom of the unit. Access to the Air Hose Nozzle and
pull out the air hose. Make sure that the Nozzle Locking Lever is in the UP position.
2. Remove the valve cap from the inflatable valve stem.
3. Attach the appropriate valve stem adaptor to the Air Hose Nozzle.
4. Press down the Nozzle Locking Lever all the way down to securely lock the valve stem adaptor.
5. Attach the compressor Air Valve Nozzle with the valve stem adaptor onto the air valve stem of the
inflatable and push down the Air Valve Nozzle as far as it travels. Make certain it is seated properly.
6. Turn the compressor Power ON/OFF Switch located on the back panel of the unit to ON position.
7. Monitor the pressure on the compressor Air Pressure Gauge while inflating.
8. Turn OFF the compressor when the desired air pressure is reached.
9. Disconnect the Air Valve Nozzle from the Air Valve Stem.
6. Replace the Valve Cap onto the Valve Stem.
7. Stow the air hose into the Compressor Air Hose Compartment.
12 VOLT DC POWER PORT OPERATING INSTRUCTIONS:
IMPORTANT: The Internal auto - reset Circuit Breaker will automatically interrupt the power if the current
drawn exceeds 10Amp.This feature prevents damage to the QuickBoost internal circuits. Internal Circuit
Breaker will automatically reset after cooling period (Approximately 10-25 minutes).
1. Remove the 12 Volt DC protective cover.
2. Insert the device 12 Volt accessory plug that can be powered by a power supply into the 12 Volt
power port of the QuickBoost.
3. Turn on the power of the 12 Volt DC device being powered by the QuickBoost unit.
LED Area Light with ON/OFF Switch:
Powerful wide angle and low power consumption LED worklight with ON/OFF toggle Switch.
Model No. 2007
Sheet 7 of 12

VEHICLE BOOST START USING THE DUAL 12VDC PLUG BOOSTER CABLE:
WARNINGS: Vehicles equipped with on-board computers may be damaged if the vehicle is jump
started. Read and understand your vehicle owner’s manual instructions before attempting to
jump-start your vehicle. Failure to follow these advisory instructions my result in explosion.
1. Turn off the vehicle ignition and all the accessories (Such as radios, lights, and air conditioners,
etc.).
2. Apply the emergency brake and put those vehicles with automatic transmission in park position.
3. Place the QuickBoost unit in the vehicle front passenger side floor board.
4. Connect the Booster Cable 12 Volt DC plug with LED power indicator into the vehicle cigarette light-
er or 12Volt DC socket.
5. Connect the other end of the Booster Cable into the QuickBoost unit 12 Volt DC port. Make certain a
good connection is made.
6. Allow a minimum of 20 minutes for the vehicle depleted battery to boost charge.
7. Disconnect the dual 12 Volt DC plug Booster Cable from the vehicle and from the QuickBoost
12 Volt DC port.
1. Start the vehicle engine.
NOTE: If the vehicle fails to start, reconnect the dual 12 Volt DC plug Booster Cable to the
vehicle and the QuickBoost 12 Volt DC port. Allow an additional 20 minutes for boost charge
before attempting to restart vehicle again.
USB OUTPUT PORT:
1. Prior to connecting the device to be powered to the USB port, make sure the USB power switch is
in OFF position. The power switch must be positioned in the middle.
2. Prior to plug in the device to the USB port, make sure the device power switch is OFF position.
3. Using the USB cable included with your electronic device to be powered or charged, connect the
USB plug into the USB port of the QuickBoost.
4. Connect the other end of the cable to the into the electronic device.
5. Press the USB port Power Switch to ON position. The device with built in rechargeable battery
will start charging automatically. Turn ON the electronic device and use as normal after charging.
6. After using the USB port, the USB Power Switch must be turned to OFF position, Otherwise the
7. internal battery of the QuickBoost will be slowly depleted, although there is no electronic device at-
tached to the USB port.
8. Turn OFF the electronic device and disconnect the cable from the USB port.
VEHICLE JUMP START INSTRUCTIONS:
WARNINGS: Vehicles equipped with on-board computers may be damaged if the vehicle is jump
started. Review and understand your vehicle owner’s manual instructions before attempting to
jump-start your vehicle. Failure to follow these advisory instructions my result in personal injury
and property damage. Use Safety Glasses to protect your eyes while working near battery during
jump-staring a vehicle. Jump start a vehicle in an open area without any type of obstructions.
CAUTIONS: Make certain that the QuickBoost Main Booster Power Switch is in OFF position
before starting to jump start a vehicle.
1. Turn off the vehicle ignition and all the accessories (Such as radios, lights, and air conditioners,
etc.).
2. Apply the emergency brake and put those vehicles with automatic transmission in park position.
3. Determine the polarity of the vehicle battery terminals. The positive (+) battery terminal normally
is larger in diameter than the negative (-) terminal. If you are unsure, you must refer to the
vehicle owner’s manual.
Model No. 2007
Sheet 8 of 12

4. Determine whether your vehicle designed with a negative or positive grounded system: In the
Negative Ground System, the negative battery terminal is grounded to chassis of the vehicle. Most
vehicles use this type of system. Positive Grounded battery terminal is grounded to chassis or any
other part of the vehicle. If you are not certain of this important information, YOU MUST REFER TO
YOUR VEHICLE OWNER’S MANUAL.
5. Remove clamps from the holders. Never allow clamps (positive & negative terminals) to touch
together or contact the same piece of metal to prevent short-circuits.
6. Follow the instructions for a Negative Grounded System or Positive Grounded System as indicated
below:
Negative Grounded System
I. Connect the RED CLAMP (positive +) to the positive terminal of the vehicle battery or the
remote positive terminal if available.
II. Connect the BLACK CLAMP (negative -) to the vehicle engine block, or a metal part of the
vehicle which is connected to the vehicle main ground system. Do not clamp directly to
negative battery terminal, main fuel distribution module or sheet metal parts.
III. The Polarity Protection System GREEN LED is illuminated if the proper connections
have been made. WARNING: If RED LED is illuminated, DISCONNECT the booster
clamps from battery terminals. Reconnect the booster clamps by reversing the
connections to the proper battery polarity.
Positive Grounded System:
I. Connect the BLACK CLAMP (negative -) to the negative terminal of the vehicle battery.
II. Connect the RED CLAMP (positive +) to the vehicle engine block, or a metal part of the
vehicle which is connected to the vehicle ground system. Do not clamp directly to positive
battery terminal, main fuel distribution module or sheet metal parts.
III. The Polarity Protection System GREEN LED is illuminated if the proper connections
have been made. WARNING: If RED LED is illuminated, STOP and disconnect the
booster clamps from battery terminals. Reconnect the booster clamps by reversing the
connections to the proper battery polarity.
7. Turn on the Main Power Booster Clamps Switch by rotating the switch to the ON position.
8. Allow 3 to 5 minutes of charge time. It is highly recommended having a second person to assist
holding the unit securely in place during the next steps.
9. Start the engine and Stop if the vehicle does not start after 2 to 3 seconds of engine cranking. Wait
2 to 3 minutes then try again. Repeat the above steps several times until the vehicle starts.
10. If the vehicle starts, turn off the Main Power Switch by turning the switch to the OFF position.
11. Disconnect the clamps as far away from the vehicle battery as possible.
For Negative Grounded System, disconnect the BLACK CLAMP Negative first and then the RED
CLAMP Positive. For Positive Grounded System, disconnect the RED CLAMP Positive first, and
then the BLACK CLAMP Negative.
12. Stow the booster clamps into their storage compartment.
12 VOLT DC CHARGER ADAPTOR FUSE REPLACEMENT:
1. Unscrew the retainer ring at the tip of the 12 Volt DC charger plug.
2. Replace the internal glass fuse with the same grade Fuse rated at 2 AMP.
Model No. 2007
Sheet 9 of 12

TROUBLESHOOTING GUIDE:
TROUBLE RECOMMENDED SOLUTION
Vehicle does not start Make sure the Polarity Protection Green LED is illuminated. Turn the Main
Power Switch to ON Position to allow power into the booster clamps.
DO NOT turn the Main Power Switch to ON position if the Polarity
Protection RED LED is illuminated. Disconnect both booster clamps and
reconnect the Booster Clamps to the proper polarity.
Allow the QuickBoost to stay connected to the vehicle battery for a longer
period of time. Wait 6 to 8 minutes before attempting to start the vehicle
again.
Recharge the QuickBoost to a FULL charge status.
Replace the vehicle battery or visit workshop/garage for further
assistance.
12 Volt DC devices Recharge the QuickBoost to a FULL charge status.
connected to the 12 Volt
output port of the Insert the device 12 Volt plug properly into the QuickBoost DC output port
QuickBoost does not operate.
Internal Circuit Breaker is OFF. Remove the 12 Volt Accessory plug from
The BEAST 12VDC output port. Wait 15 - 25 minutes for automatic
Reset to regain power.
Compressor does not Recharge the QuickBoost internal battery to Full charge.
turn on.
Compressor does not inflate Make sure the hose nozzle is properly seated and the locking lever is in
down position.
Repair air hose if possible.
Allow 10 to 15 minutes for compressor to cool down before re-use.
USB powered device Press the USB output port SWITCH to ON position (—)
connected to the USB of
The QuickBoost doesn’t Insert the device USB plug properly into the QuickBoost USB port.
Function.
Model No. 2007
Sheet 10 of 12

SPECIFICATIONS:
 Battery rated capacity ——————————————— 12 Volt - 10 Ah
 Air Compressor —————————————————– 260 PSI with 100 PSI Air Pressure Gauge
 12 Volt DC output ports output Amp.————————– 10 A
 USB ports output rating —————————————— 5 Volt - 500 mA
 LED Area light —————————————————— 120 mA
 Unit dimensions - Handle in down position —————— 9 1/2” H x 9 3/8” W x 5 7/8” D
 Unit dimensions - Handle in up position ——————— 11 1/2” H x 9 3/8” W x 5 1/4” D
 Unit weight without AC/DC charging adaptors ———— 12 lbs.
NOTE: Specifications are subject to change without notice.
LIMITED PRODUCT WARRANTY AND LIABILITY
MobilePower, LLC. warrants to the original purchaser that the Vehicle Boosting System shall be free from material defects in
constructing material and workmanship for a period of two years from the original date of purchase except the internal Lead Acid
rechargeable battery pack warranted for a period of one year. If the product is determined by MobilePower, LLC. to be defective in
material and workmanship during the warranty period, MobilePower, LLC. will repair or replace the defective product or defective
accessories/components with the factory original specifications product at MobilePower, LLC. option. The original purchaser is
entitled to obtain this warranty with the proof of purchase within the warranty period. To obtain a return authorization and shipping
instructions related to the warranty services in North America visit us at www.mobilepower-us.com or call (800) 708 – 8550
Customer Support or contact us at [e-mail]. You may ship the defective product with freight prepaid to
MobilePower, LLC. Your replacement will be mailed back to you at no additional charge.
Great care must be taken when packing the product and all associated accessories into a suitable packing box along with original
dated purchasing receipt or invoice. The package must include a letter stating the defect details, contact information including
physical address. Any address with a PO Box will not be processed and will be held until further notification from the consumer.
Make certain that your package can be tracked when you are shipping the defective products to us. MobilePower, LLC will not be
responsible for lost packages sent by consumers. MobilePower, LLC. Will not be responsible for damages incurred during
shipment to our facilities. Failure to provide the original purchase receipt or proof of purchase will render this warranty invalid.
THIS WARRANTY SHALL NOT APPLY IF THIS PRODUCT (A) IS DAMAGED RESULTING FROM ABUSE, MISUSE,
NEGLIGENCE, ACCIDENT, LACK OF MAINTENANCE, WEAR AND TEAR, UNREASONABLE USE OR BY OTHER CAUSES
UNRELATED TO THE DEFECTIVE MATERIAL OR WORKMANSHIP; (B) IS USED WITH PRODUCTS THAT ARE NOT
COMPATIBLE WITH VEHICLE BOOSTING SYSTEM; (C) IS USED FOR COMMERCIAL PURPOSES; (D) IF THE PRODUCT
HAS BEEN SUBJECTED TO WATER AND FIRE.
This warranty provides you with specific legal rights, and you may also have other rights which vary from state to state. This
warranty is valid only in North America.
MobilePower, LLC. Bluffton, SC 29910
www. Mobilepower-us.com Office: (800) 708 - 8550
[e-mail]
Model No. 2007
Sheet 11 of 12

Model No. 2007
Sheet 12 of 12
MobilePower, LLC. Bluffton, SC 29910
www. Mobilepower-us.com Office: (800) 708 - 8550
[e-mail]
[e-mail]
Made in China