FamilyTool FMT002JST User manual

1 IM-FMT002JST-R0
INSTRUCTION
MANUAL
14,000mAh Car Jump Starter
mod. FMT002JST
Warning!: When using lithium-
should always be followed to reduce the risk of fire, personal injury and material damage.
• Read all of this manual carefully before using the Jump Starter. Retain this manual for future
reference
• 


• efore first use charge the device for 3 hours or more.
• Working in vicinity of a lead-
 

TECHNICAL SPECIFICATION
 -ion Voltage: 12 V dc
 Input: 12V/15V dc 1 Amp able length: 12”
Output: 1x US 5V/2Amp, 1x 12V/2Amp, 1x 19V/3.5Amp 
2 IM-FMT002JST-R0
Fig. A
Fig. B
7
5
Fig. H
Fig. D
Fig. F
3
Fig. E
4
6
Fig. C
2
1
Fig. G
8
1
2

3 IM-FMT002JST-R0
Work Area Safety
1. Keep work area clean and well lit. 
2. Do not operate Jump Starter in explosive atmospheres, such as in the presence of flamma-
ble liquids, gases or dust. The Jump Starter can create sparks which may ignite the dust or
fumes.
3. Keep children and bystanders away while operang the Jump Starter
cause you to lose control.
4. Store idle equipment. Always lock up tools and keep out of reach of children.
Electrical Safety
1. Do not operate if ower ack has received a sharp blow, been dropped, or otherwise dam-
aged in any way.
2. Do not expose to rain or wet condions. Water entering the Power Pack will increase the
risk of electric shock.
3. Do not use an extension cord with this item.
4. Use of an aachment not recommended or sold by the manufacturer may result in a risk
of fire, electric shock, or injury to persons.
5. Do not operate with damaged cord or plug. Replace the cord or plug immediately.
Jump Starter Safety Warnings
1. Lead-acid baeries generate hydrogen gas when charging. Hydrogen gas is explosive. Only
use the Jump-Start system in a well-
2. Use the tool for ump starng a LEAD-ACID baery only.
3. e sure area around baery is well venlated 

4. Do not aempt to ump start a vehicle with a non-rechargeable or defecve baery.
5. DO NOT TOUCH OSITIVE AND NEGATIVE BATTERY CLAM S TOGETHER.
6. Unplug the ower ack from its Adapter 
7. Connect and disconnect baery cable clamps only a'er Jump Starter is OFF 


8. DO NOT O EN HOUSING. Contains no user-serviceable parts. Internal parts may be electri-
fied, even with unit off.
9. Do not use if the Jump Starter is device is swollen or damaged.
10. Do not use the Jump Starter to power sensive devices such as medical devices. Do not

11. Some rechargeable tools and appliances can damage the Jump Starter. Check the temper-
ature of the device several mes when it is charging. If the device becomes extremely hot;
turn the power off, remove the device, and do not use with the Jump Starter again.
12. Do not aempt to power a device, or combinaon of devices, that will require more than
the rated output of this Jump Starter
devices..
13. Do not expose Jump Starter to temperatures over +113°F (+45°C) or under -14°F (-26°C) as
 
could create a safety hazard.
Checking Charge and Charging the Power Pack
1. Indicator Lights
The Jump Starter has 5 indicator lights to determine the amount of power in the unit
(see fig A-4). When all five lights are lit the unit is fully charged.
Press the on/off switch (fig A-
The indicator lights will flash one by one when the unit is charging. A solid light indi-
cates a complete level of charge. For example, when 2 lights are illuminated and a
third is blinking, that means the unit is around 50% charged.
When all the indicator lights are lit, the charging is complete and the unit will auto-

2. Charge the Jump Starter
a. charge with the wall plug. Plug the 120VAC Adapter (fig. F) into a wall outlet.
4 IM-FMT002JST-R0
b. charge with the car adaptor in your vehicle. Plug the Car Adaptor (fig. D-1) into a

The unit will charge in approximately 4hours.
Use
A) Jump Starng a Vehicle
Note: Read the vehicle owner’s manual pertaining to jump starng prior to using the Jump Start-
er.
1. -5) to verify that the Jump Starter is fully charged. Do not pro-
ceed if the power is less than 40% (at least 3 lights must be on). Recharge if needed.
2. 
3. 
4. When using the clamps, DO NOT allow the metal teeth of the clamps to touch one another.
This is a short circuit which could cause a spark and all electrical components..
5. -) terminal, or the LACK

and could damage all electrical components.
6.  
-

7. Check the Jump Starter is OFF (no lights).
8. Securely fasten the clamps into the Jump Starter (fig G) and put the Jump Starter is a secure

9. Power ON your Jump Starter (figure A-5).
10.  
detach the Jump Starter from the clamps. Wait 60 seconds and then follow steps 7-10. If

11. 

12. You are now able to drive your vehicle. You should be sure to run your vehicle for at least 15

B) Charging hone, Tablet or other USB devices
With your FamilyTool Jump Starter you can recharge all your USB devices very easily
3. Select the right cable adapter (fig C)
4. Insert the US cable in the 5V/2.1 A US output port (fig A-6)
5. Insert the other side of the cable into the input port of your device
6. -5)
C) Charging Laptopor similar devices
1. Select the laptop adapter (fig E)
2. Connect the adapter to the laptop charging cable (fig D-2)
3. Insert the laptop charging cable in the 19V/3.5 A output port (fig A-3) or to the 12V/2A
output port (fig A-
4. Insert the other side of the cable into the input port of your laptop
5. -5)
D) LED flash light
1. -5) for 3 seconds to start the LED flashlight. y pushing the
-5) you can cycle between the 3 modes available (normal, strobe and
SOS)
Maintenance
 
 
• Do not store unit in extreme temperatures.
