Mobiletron VFLC00090 User manual
V1
V2
COLOR TFT LCD MONITOR
OPERATING INSTRUCTION
Before operating this set, please read these instructions completely
Solutions for:
- rear vision systems
- car entertainments
TFT LCD MONITOR TFT LCD MONITOR
SAFETY PRECAUTIONS
(Improper handling from ignoring
the following may result in serious
injury or death)
Do not watch TV programs and operate the monitor while
driving; it may cause a car accident because of the distraction.
Do not install the monitor where it may be viewable to the driver,
or obstruct an air bag device.
In case of smoke or rare odor from the monitor, power off the
equipment and contact your local dealer.
Do not attempt to service this product on your own. Disconnect
power to the unit and contact your local dealer.
Dropping the unit will cause possible internal mechanical failure.
.Hitting or striking the monitor unit is prohibited
Do not open the monitor body.
In case of changing a fuse make sure to replace it with the
same amperage.
The monitor should be situated away from direct sun light,
heat, water or moisture.
CAUTION
*,
:7
:LED
:480 (RGB) x 234
:0.107mm x 0.370mm
:400cd/m
2(nits)
::40 /:60 /:60 /:60
:DC12–24V
:1Vp-p
:75 ohms
:NTSC / PAL
- OSD :,,,
,,
-()
-NTSC/PAL
-
- DC12–24
-,AV2
-
-
TFT LCD MONITOR TFT LCD MONITOR
Specifications
7" active matrix TFT-LCD (16:9)
LED back light
480 RGB (H) x 234 (V)
0.107mm(W) x 0.370mm (H)
400 cd/m (Nit)
40/60/60/60 degrees (T/R/L/B)
R.G.B.
12-24 VDC
Stripe
1Vp-p (positive) 75 ohms
NTSC/PAL Auto Detection
2
Display:
Back Light:
Dot Format:
Dot Pitch:
Brightness (typ.):
View angle (CR>10)
Video signal:
Video system:
Pixel configuration:
Power requirements:
Features
- OSD (on screen display) control for: Color, Tint, Brightness, Contrast
and Mirror (for Camera Mirror/Front View switch)
- NTSC/PAL Signal Auto Detection
- Audio Speaker is included
- DC 12-24 V power input
- Provide DC 12V power to cameras
- Auto brightness adjustment function(For VFLC00090 ONLY)
- 2 Camera inputs, CCD1 is default. CCD2 for Reverse operation.
- Auto switch from default CCD1 input toCCD2 input source to check
view behind the car while driver set the gear to Reverse
- Monitor auto power on while Reverse Gear Signal detected
*Design and specifications are subject to change without notice
PRINTED IN TAIWAN
:
，
。
l，
。
l
。
l
。
l，
l
。
l，
。
l。
l
。
TFT LCD MONITOR TFT LCD MONITOR
Mainframe
Function Introductions:Function Introductions:
1. Press the "POWER" key to turn on the monitor.
2. Press "MENU" key to select the adjustment item. The
sequence of adjustment item is shown as following,
3. You can use UP/DOWN key to adjust corresponding item
shown on the screen.
4. Press “V1/V2” key to change the video source
Press "MENU" key again to go to the procedure 3.
REMARK:
Mute or Vocal (default) function is operated by "DOWN or UP” key.
1.Volume: smaller volume to louder
2.Brightness: less bright to more bright
3.Contrast: lower intensity to higher intensity
4.Saturation: lighter to richer
5.Hue: reddish to greendish
6.Power mode:
Auto On Off
7.
1.
Power on source:
AV1 AV2
8.Power On Speed
Normal Fast
9. Auto Brightness(FOR VFLC00090 ONLY)
Off On
0 Default: all adjustment can be returned back to
pre-set value.
V1 / V2
Down/Up
V1
V2
Menu
Power
A
，
1.
AB
2.
AB
B
TFT LCD MONITOR TFT LCD MONITOR
Power
Down/Up
Menu
V1
V2
V1 / V2
1.
2.
3.
4.
。
。
。
。
[]
[] :
[/ ]
[1/2]
[]
:
() [/ ]
POWER
Menu
UP DOWN
VV
MENU 3
UP DOWN
1.Volume
Brightness
Contrast
Saturation
Hue
Power mode
AUTO On Off
Power on source
AV 1 AV 2
8.
9.Auto Brightness: (
Off On
10.Default
:
:
:
:
:
:
:
:()
00090)
2.
3.
4.
5.
6.
7.
Power on speed
Normal Fast
:
VFLC
Monitor Stand Installation DiagramMonitor Stand Installation Diagram
STEP 1: Slide the A part into the slide track of B part
to be complete stand.
STEP 2: Slide the rear of the monitor housing into the
complete stand. Then it's completed.
PART A
PART B
TFT LCD MONITOR TFT LCD MONITOR
Fuse
(250V/2.5A)
Installation DiagramInstallation Diagram
WARNING:
For safety reason please MUST turn off engine of vehicle before
any camera or extension cable change or connect with control box.
NOTE :
The Video 2 is default with normal image
for back view camera
Black Wire: to power ground
Green Wire: to Reverse Gear light for reverse gear operation
Red Wire: to power (DC12V - 24V)
Black: Video 1 in, Audio 1 in & DC12V out
6 pin mini din lock-type (female)
(Disable for VFLC00090)
Red: Video 2 in, Audio 2 in & DC12V out
6 pin mini din lock-type (female)
(Default for back view camera)
，
。
:
V1
V2
2
:
1 1,
)
: , DC12V
6 pin mini din ( )
(VFLC00090
:
!(+)"#$%&'*-:
. /: DC12V -24V
. 2 2,
0)
: , DC12V
6 pin mini din ( )
(
(250V/2.5A)
100cm
V1
V2
100cm
Table of contents
