Mode Machines DT200 User manual

MANUAL
DT200

PANEL DESCRIPTION
PAGE 2
16’
8’ 4’
16’
8’ 4’
LFOLFO ENVENV
RANGE
WAVEFORM
X MOD
ENV
DELAY TIME
SOURCE MIX
CUTOFF FREQ
LFO MOD
PITCH FOLLOW
ATTACK
MANUAL
RELEASE
ENV
GAT E
DCO-1 VCF
MODE
LEVEL
CHORUS
SUSTAIN
VCADCO-2
NOISE
SYNC METAL
ON
OFF
OFF
HPF
RESONANCE
ENV MOD
MODE
DECAY
RANGE
WAVEFORM
LFO
WAVEFORM
ON
OFF
FREQ MOD
TUNE
FINE TUNE
MODE
RATE
ON
OFF
FREQ MOD
DCO-1 DCO-2
RND
LFO ENVELOPE
DTronics design
VCA Mode
1
2
3 4
5
6
7 8
9 10
11 12
13 14
15 16
17
18
19 20 21 22 23 24 25
26 27
28
1
2
3
4
5
6
7
8
9
10
Cross modulation
Tune
Fine Tune
Source mix
HPF Cuto Frequentie
Range
Waveform
LFO Depth / ENV Depth
Frequentiemodulation
LFO /ENV switch
Polarity switch
11
12
13
14
15
16
17
18
19
20
Cuto Frequency
Resonance
Delay Time
LFO Waveform
VCA Mode
VCA Level
Pitch follow
LFO Modulation
ENV Modulation
Polarity switch
21
22
23
24
25
26
27
28
Rate
DIN jack
Sustain level
Release Time
Manual Button
Chorus switch
Attack Time
Decay Time

Basic Connections an Operations
Make sure that the JX-3P is turned off
Connect the DIN jack and the Programmer Input jack on the rear panel of the JX-3P with the
DIN cord (6p)
Set the Ext. Selection switch on the rear panel of the JX-3P to the Programmer position.
Turn the JX-3P on. The JX-3P supplies power to the DT200
When the DT200 is turned on, the Red LED will flash 2 times, showing everything is ok.
The DT200 has no sound source itself, therefore no sound is obtained unless connected to
the JX-3P.
If the red LED stays on, there is no communication with the synthesizer, this can be a
defective cable or defective synthesizer.
A WRITE button is not present on the DT200. To write patches to memory, use the WRITE
button on the synthesizer.
1)
2)
3)
4)
5)
6)
PAGE 3

SPECIFICATIONS
[Programmer DT-200]
DCO-1
Range (4' , 8' , 16')
Waveform ( )
Frequentie Modulation (LFO, ENV)
DCO-2
Range (4' , 8' , 16')
Waveform ( )
Tune (Approx. +/- 1200 cent)
Fine Tune (Approx. +/- 50 cent)
Frequency Modulation (LFO, ENV)
Cross Modulation (Sync, Metal)
Modulation Sens (LFO, ENV)
VCF
Source mix
HPF
LPH
VCA
Mode (ENV, Gate)
Level
PAGE 4
Cutoff Frequency
Cutoff Frequency
Resonance
ENV Modulation
Polarity
LFO Modulation
Pitch Follow
ENV
Attack Time
Decay Time
Sustain Level
Release Time
LFO
Waveform ( Random)
Delay Time
Rate
Chorus
Chorus switch (ON / OFF)
Function buttons
Manual button
DIN jack
DIN6P
Dimensions
218(W) 150(D) x 40(H)mm
Weight
0.9 kg
Accessories
DIN cord (DIN6P)
Specifications are subject to changes
without notice
, ,
, ,

CONTACT
PAGE 5
For information, pictures and accessories to
our product line, please visit:
www.modemachines.com
Information, product news and many
other interesting articles can be found at
www.facebook.com/modemachines
You also get news and links from Twitter.
Follow us on
www.twitter.com/modemachines
Mode Machines is a Division of Michael
Thorpe Consulting GmbH
Fichtenstraße 49 • 90763 Fürth • Germany
Tel: +49 (0)911 - 97 92 92 -0
Fax: +49 (0)911 - 97 92 92 - 18
Email: [email protected]
The DT200 is a DTronics design
More information about our products on
www.dtronics.nl