modway EEI-2855-GRY-WAL User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI –2855 TV STAND
Thank you for purchasing the MODWAY TV STAND！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the TV stand, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
3 Allen Wrench M4 x1
Components:
A Top Panel x1 D
Leg x4
B
Metal Frame x2
1 Bolt M6x12mm x24
2 Castor x4
C
C
A
D
B
C Shelf x1
C
C
A

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI –2855 TV STAND
STEP 1:
STEP 2:
Put Top Panel (B) upside down on a carpeted or padded surface.
Place 1 piece of Metal Frame (A) to Top Panel (B).
Insert 4 pieces of Bolt (1) into the pre-drilled holes on Top Panel (B) through the pre-drilled holes on Metal Frame (A).
Use Allen Wrench (3) to tighten Bolts (1). Do not fully tighten Bolts (1) at this step.
Hardware & Tools required
Hardware & Tools required
1x4 3x1
1x4 3x1
1
A
B
1
3
1
1
Put Shelf (D) upside down on a carpeted or padded surface.
Place 1 piece of Metal Frame (A) to Shelf (D).
Insert 4 pieces of Bolt (1) into the pre-drilled holes on Shelf (D) through the pre-drilled holes on Metal Frame (A).
Use Allen Wrench (3) to tighten Bolts (1). Do not fully tighten Bolts (1) at this step.
A
D
1
1
1
3
1

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI –2855 TV STAND
STEP 3:
STEP 4:
Hardware & Tools required
Hardware & Tools required
1x16 3x1
Put the assembled Metal Frame (A) and Top Panel (B) upside down on a carpeted or padded surface.
Place 4 pieces of Leg (C) to the assembled Metal Frame (A) and Top Panel (B) as shown.
Insert 8 pieces of Bolt (A) into the pre-drilled holes on Metal Frame (A) through the pre-drilled holes on Legs (C).
Repeat the same steps for the assembled Metal Frame (A) and Shelf (D).
Use Allen Wrench (3) to tighten all the Bolts (1) clockwise until secure.
1
A
B
1
3
1
1
A
C
2
2x4
Tighten 4 pieces of Castor (2) into the bottom of assembled Legs (C) by hand clockwise until secure as shown.
B
A
D
C
C
C
2
2
2
A
D
1
1
1
1
1 1
1
1
1
1
1 1
C
C C
C
C
A
1
3 1

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI –2855 TV STAND
STEP 5:
Carefully turn over the assembled TV stand.
Assembly is complete. Your TV stand is ready to be used now!