modway EEI-2680 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI-2680/2681 TV STAND
Hardware:
Components:
ADouble-ended Bolt M8x190mm x6
B
1 Top Panel x1
Thank you for purchasing the MODWAY TV STAND！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the TV stand, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
2 Side Panel x3
D
3 Bottom Panel x1
E
F
G
H
C
Dowel ɸ8x40mm x12
Nut M8 x6
Flat Washer M8 x10
Box Wrench #8 x1
Mat 40x40mm x4
Allen Wrench #5 x1
Bolt M8x35mm x4
1
2
3
2
4
4 Leg x2
4
2

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
TV STAND
STEP 1:
Ax6 Hardware & Tool required
STEP 2:
1
Put Top Panel (1) upside down on a carpeted or padded area.
Insert 6 pieces of Double-ended Bolt (A) into the corresponding holes In the Top Panel (1) by hand as shown.
Tighten all the Double-ended Bolts (A) clockwise until secure.
Bx12 Hardware & Tool required
Insert 4 pieces of Dowel (B) into 4 holes of Side Panel (2) as shown.
Repeat the same steps for the remaining 2 pieces of Side Panel (2).
Position the assembled Side Panel (2) to Top Panel (1) as shown.
Please confirm the assembled Double-ended Bolts (A) and Dowel (B) have been inserted into the pre-drilled holes
in Top Panel (1) fully as shown.
2
2
1
2
2
B
B
B
B
A
A
B
B
A
A
A
A
A
A
EEI-2680/2681

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
TV STAND
STEP 3:
Cx6 Dx6 Ex1 Hardware & Tool required
STEP 4:
1
Put Bottom Panels (3) upside down on a carpeted or padded area.
Position 1 piece of Bottom Panel (3) to the assembled Top panel (1) and Side Panels (2) as shown.
Please confirm the assembled Double-ended Bolts (A) and Dowels (B) have been inserted into the pre-drilled holes in
Bottom Panel (3) fully.
Insert 6 pieces of Nut (C) with 6 pieces of Flat Washer (D) into the assembled Double-ended Bolts (A) as shown.
Use Box Wrench (E) to tighten all the Nuts (C) clockwise until secure.
Dx4 Fx4 Gx1 Hx4 Hardware & Tool required
2
Position 1 piece of Legs (4) to the assembled Top Panel (1), Side Panels (2), and Bottom Panel (3) as shown.
Insert 2 pieces of Bolt (F) with 2 pieces of Flat Washer (D) into the pre-drilled holes In ihe Bottom Panel (3) through the
holes In the Leg (4).
Use Allen Wrench (G) to tighten Bolts (F) clockwise until secure.
Repeat the same steps for the other piece of Leg (4).
Tear off the sticker on the 4 pieces of Mats (H).
Carefully attach 4 pieces of Mat (H) to Legs (4) as shown.
2
2
2
3
3
D
C
E
E
1
2
2
4
4
3
3
4
D
F
G
H
4
EEI-2680/2681

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
TV STAND
STEP 5:
Assembly is complete. Your TV stand is ready to be used now!
Carefully turn over the assembled TV stand.
EEI-2680/2681