Moen Plastic Pulldown Kitchen Faucet User manual

INS13314 - 3/09
Adjustable Wrench
Plastic Pulldown
Kitchen Faucet
INSTALLATION INSTRUCTIONS
Record Purchased Model Number:
(Save instruction sheet for future reference)
Image is for reference only
(Style varies by model)
Wire Cutters
剪线钳
活动扳手
图片仅供参考
（款式因型号而异）
记录购买的型号：
（保存安装说明书以备将来参考）
塑料抽拉厨房龙头
安装说明书
如需安装支持，配件丢失等，请联系MOEN。
对于中国大陆以外的市场，请自选当地经销商。
(中国大陆) 400-630-8866
(中国大陆) www.moen.cn
(中国大陆以外) www.moen.com.hk
PLEASE CONTACT MOEN FIRST
For Installation Help, Missing or Replacement
Parts. For markets exclude Chinese mainland,
please consult your local dealer.
(Chinese Mainland) 400-630-8866
(Chinese Mainland) www.moen.cn
(Exclude Chinese Mainland) www.moen.com.hk
推荐工具
为了安全和让安装和替换变得容易，Moen建议
您使用以下工具：
HELPFUL TOOLS
For safety and ease of replacement, Moen
recommends the use of these helpful tools.
十字螺丝刀
Cross Screwdriver
Safety Glasses
护目镜

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET:
Always turn water supply OFF before removing existing faucet or disassembling the valve.
Open faucet handle to relieve water pressure and ensure that complete water shut-off has
been accomplished.
移除旧龙头注意事项：
拆除现有水龙头或拆卸阀门之前，请务必先关闭供水。打开水龙头手柄以释放水压，确保完
全关闭水源。
2
Parts List
零配件清单
A.
B.
C.
D.
E.
F.
A.
B.
C.
D.
E.
F.
密封垫片
橡胶垫片
金属垫片
安装螺母
螺钉
配重块
图标图例
Icon Legend
水槽上方
Above sink
警告
Warning 水槽下方 Below sink
Seal Gasket
RubberGasket
Metal Washer
Mounting Nut
Hose Weight
Screw
水龙头本体
G.
Faucet Body
H. 抽拉软管
G.
Pullout HoseH.
B
C
D
E
F
AA
A
AAH
G

Connect the hot and cold water pipes to the hot and cold water inlet.

将水龙头冷热水管分别正确的连接到冷热进水口。
3
1
4
2
Place the seal gasket (B) on the mounting hole and insert the
faucet body (A) into the mounting hole.
Install the rubber gasket (C) and metal washer (D) on the faucet body
(A) in turn.
Screw the mounting nut (E) into the faucet body (A) and tighten the
Screw (F) using a Phillips screwdriver.
将密封垫片（B）放在安装孔上，并将水龙头本体（A）装入安装孔
内。
将橡胶垫片（C）、金属垫片（D）依次装到水龙头本体（A）上。
将安装螺母（E）旋入水龙头本体（A）中，然后使用十字螺丝刀将
螺钉（F）旋紧。
AA
A
AAB
C
D
A
E
F
A
34
热
Hot
冷
Cold

7
6
8
4
Turn the faucet to off, then turn on the hot and cold pipes.
Attach the pullout hose (H) to the outlet hose and push it inwards as
far as possible until you hear a "click" and pull down to check that it
is securely installed. 
Note: If you want to remove the pullout hose (H), press the button
and pull it down.
Use a screwdriver to open the hose weight (G), then install it on
the pullout hose (H), and use the screwdriver to lock the screw. 
Note: Please adjust and ensure smooth operation of pull function
when installing hose weight.
Open the handle and observe whether the water outlet flows
smoothly.If the water flow is not smooth, please refer to the
next step.
将抽拉软管（H）装到出水软管上，尽可能的往内推，直到听到
“咔哒”声，向下拉检查是否安装牢固。
注意：如果想拆下抽拉软管（H），可按下按钮并向下拉出。
将水龙头调整到关闭状态，然后打开冷热水管开关。
使用螺丝刀将配重块（G）打开，然后安装到抽拉软管（H）上，
并用螺丝刀将螺钉锁紧。
注意：安装配重锤的时候请调整并保证抽拉功能操作顺畅。
打开把手，观察出水口水流是否顺畅。如果水流不顺畅，请参照下
一步。
5
安装区域
Install zone
开
open
关
close
AAH
出水管
G
AAH

t
9 10
5
Close the handle, unscrew the pullout hose head and flush the
internal screen until it is free of visible debris and clogs, then
reinstall the pullout hose head.
Open the handle again and the water flow returns to normal.
If not, repeat the previous step.
关闭把手，旋下抽拉头并冲洗内部的滤网，直至没有可视的碎屑和
堵塞物，然后重新安装好抽拉头。
重新打开把手，水流恢复正常，如果没有恢复请重复上一步操作。
关
close 开
open

6
产品使用说明 Usage Instructions
把手温度调节范围0°~90°，开启角度范围0°~22.5°
注意热水开启位置，防止烫伤。。
Handle temperature adjustment range 0° to 90°,
opening Angle range 0° to 22.5°.
Pay attention to the hot water opening position to
prevent burns.
弯管在使用过程中如果不小心被拔出，用手将弯管向下压到位即可。
If the pipe is accidentally pulled out during use, press the pipe
down until it is in place.
45°
45°
35°
Cold
Hot 22.5°
Closed
Open

塑料抽拉厨房龙头
Plastic Pulldown
Kitchen Faucet
合格证
产品名称
检验员
生产日期
摩恩（上海）厨卫有限公司
MOEN (SHANG HAI) KITCHEN&BATH PRODUCTS CO.,LTD
No. 399 Fute North RD, China (Shanghai) Pilot Free Trade Zone,
Shanghai 200131 P.R. China
中国（上海）自由贸易试验区富特北路399号
邮编：200131
Compliance Certification
Inspector
Product Name
Date of Production