Monaco 134 06 05 User manual

Monaco
Multi fuel stove
BS EN 13240
Model : 134 06 05
Nominal output :
5,9 kW (wood)
8,8 kW (solid mineral fuels)
Description of the appliance
Installation instructions
Operating instructions
Spare parts
Warranty certicate
Document n°1303-2
25/10/2012
Technical manual
to be saved
by the user
for future reference
Parc d’activités de la Verte Rue
Allée des Prêles
59270 BAILLEUL
Tél. : [phone]
Subject to modications

Monaco - 134 06 05
2 Technical manual "1303"
Package......................................................p. 3
General characteristics.................................p. 3
Appliance description...................................p. 3
Operating principle ......................................p. 3
Warning to the user.....................................p. 4
Location of the unit .....................................p. 4
Mounting the ue collar ...............................p. 5
Smoke exit on the top .................................p. 5
Smoke exit at rear.......................................p. 5
Flue............................................................p. 5
Chimney connector......................................p. 6
Door closing pressure ..................................p. 6
Pre-utilisation check ....................................p. 7
Maintenance of the chimney.........................p. 7
FRANCO BELGE congratulates you on your choice.
FRANCO BELGE, guarantees the quality of its appliances and is committed to meet
its customers’ needs.
FRANCO BELGE, which can boast a 80-year experience in the industry of heating devices,
uses state-of-the-art technologies
to design and manufacture its whole range of products.
This document contains instructions on how to install your appliance and make full use of
its functions, both for your comfort and safety.
CONTENTS
Product information .................................................................................................................... p. 3
Installation instructions............................................................................................................... p. 4
Instructions for user .................................................................................................................... p. 8
Spare parts ..................................................................................................................................p. 12
Fuel............................................................p. 9
Instruction for use with wood.......................p. 9
Refuelling procedure....................................p. 9
Operating procedure
when using solid mineral fuels .....................p. 9
De-ashing ...................................................p. 9
Maintenance of the chimney....................... p. 10
Maintenance of the stove........................... p. 10
Safety advice ............................................ p. 10
Trouble shooting ....................................... p. 11

Monaco 134 06 05
Technical manual "1303" 3
1.1. Package
• 1 package : stove.
1.2. General characteristics
* Authorised fuels under section 20 of the clean air act.
1.3 Appliance description
Multifuel stove - in conformity with BS EN 13240.
• Intermittent-burning heating appliance.
• Detachable ue spigot for rear or top chimney connection.
• Front loading door tted with large refractory glass panel.
• Adjustable primary air for controlling the burning rate.
• Large ash-pan.
1.4 Operating principle
The “ MONACO ” is designed for operation with the door
closed. Heat is mainly diffused by radiation, through the
window and body of the appliance.
Combustion occurs on the grate, with draught entry through
the top of the combustion chamber when using wood and
under the grate when using smokeless fuels.
Reference ........................................134 06 05
Nominal heat output............................. kW 5,9
Chimney draft required .......................... Pa 12
Hearth dimensions
- width ............................................... mm 429
- depth ............................................... mm 240
- height .............................................. mm 225
Log dimensions
- lenght maxi ........................................cm 40
Ash pan capacity ................................litres 2,2
Net weight............................................ kg 90
Heated Volume .................................... m3 180
PERFORMANCE WITH WOOD
Efciency (net).......................................% 75,7
Co (13% O2) .........................................% 0,28
- Mean ue gas temperature .................. °C 317
- Flue gas mass ow............................. g/s 4,9
PERFORMANCE WITH MINERAL SOLID FUELS (smokeless fuels)*
Nominal heat output ............................. kW 8,8
Efciency (net)........................................% 70,6
Co (13% O2) ..........................................% 0,15
- Mean ue gas temperature ................... °C 374
- Flue gas mass ow............................. g/s 5,8
1. Product information
This appliance is meant to burn wood safely
WARNING
Incorrectly installed, this appliance can be dangerous and possibly cause serious accidents.
We recommend that you engage the services of a professional engineer for its installation
and the regular maintenance requirements
Figure 1
Dimensions in mm
561
599
654
566 433
388
141
449
Ø139
Ø125

Monaco - 134 06 05
4 Technical manual "1303"
2.1 Warning to the user
All the local and national regulations, and
in particular those relating to national and
European standards, must be observed when
installing the appliance.
An incorrectly installed heating appliance can
cause serious accidents (chimney res, burning of
plastic insulation materials, in partition walls, etc.).
This stove is exempted by DEFRA for burning wood
logs in UK Smoke Control Areas (SCA). DEFRA
exemption is dependent upon the appliance being
tted with a mechanical stop to prevent closure of the
secondary air control beyond the 25% open position.
You should check that this stop mechanism is tted
before installation of the stove and certainly before
using the stove in a SCA to burn wood logs. If the stop
mechanism is tted then the minimum chimney ue
diameter can be 125 mm but if the stop mechanism
is not tted then the stove is not exempted and
the minimum chimney ue diameter is 150 mm in
accordance with Approved Document J of the building
regulations.
The insulation of both the appliance and the
exhaust gas pipe has to be reinforced and done
according to the Standards and the Building Regulations
for safety reasons. The installation must be carried
out according to the Standards and the Building
Regulations. Failure to respect the manufacturer’s
instructions will invalidate the warranty.
The manufacturer’s responsibility shall be limited to
the supply of the appliance.
2.2 Location of the unit
Ventilation : For satisfactory appliance operation
with a natural draught, check that sufcient air
for combustion is available in the room. In houses
equipped with one VMC (controlled mechanical
ventilation), this one aspire and renew the ambient
air ; in this case, the residence is under slight low
pressure and a non-sealable external air intake must
be installed in addition to the chimney itself, at least
50cm² in section.
Position of the unit : For new installations, select
a central position within the house, to provide a
good heat distribution around the building. The heat
distribution towards the other rooms will be made
through the communicating doors. These rooms must
be at low pressure or tted with non-adjustable
air registers, placed so that they cannot be
obstructed, to encourage circulation of the hot air.
Floor and walls : make sure there are not combustible
or covered with non combustible material. Otherwise
it must be necessary to install a non combustible
protection.
2. Installation instructions
Figure 3 - Minimum clearances
Figure 2 - Smoke exit on the top

Monaco 134 06 05
Technical manual "1303" 5
There must be a clearance of at least 150 mm at each
side (back and sides) of the appliance in accordance
with the below recommandations from a non
combustible wall. This distance must be extended to
a minimum clearance of 650 mm side and 700 back
from any combustible material.
If any part of the back or sides of the appliance lies
within 150 mm horizontally of the wall, than the wall
should be of solid non-combustible construction at
least 50 mm thick from level to a level of 200 mm
above the top of the appliance and 1200 mm above
the hearth.
Il however, any part or sides of the appliance lies
within 50 mm of the wall, then the wall should be of
solid non-combustible construction at least 200 mm
thick from oor level to a level of 300 mm above the
top of the appliance and 1200 mm above the hearth.
Where the hearth itself in at least 150 mm from an
adjacent wall.
There is no requirement for protection of the wall. It
should be noted that these thicknesses of solid non-
combustible material can be substituted by thinner
material if the same overall level of protection can be
achieved.
When using a single wall ue pipe, there must be
a clearance (A) of at least three times its diameter
(B) from any combustible materials. If the appliance
has to be located in an opening, this distance must
be extended to a minimum clearance (A) of 450 mm
from the pipe or the stove body to any combustible
materials.
Hearth : The appliance must stand on a reproof
hearth. It is possible to provide a hearth made of
non combusible board/sheet material or tiles at least
12 mm thick (C). Constructional hearths should be
constructed of solid non combustible material at least
125 mm thick (including the thickness of any non
combustible oor under the hearth).The hearth must
protrude at least 300 mm in front of the stove and
150 mm each side. Hearths are provided to prevent
combustion appliances setting re to the building
fabric and furnishings and to limit the risk of people
being accidentally burnt.
Therefore, they should be separated from adjacent
combustible materials and should be satisfactorily
delineated from surrounding oor nishes (carpets
etc.) as follows.
Combustible material should not be placed under a
constructional hearth for a solid fuel appliance within
a vertical distance of 250 mm from the upper surface
of the hearth, unless there is an airspace of at least
50 mm between the combustible material and the
underside of the hearth.
Where a superimposed hearth has been placed onto a
constructional hearth, combustible material placed on
or besid the constructional hearth should not extend
under the superimposed hearth by more than 25 mm
or closer to the appliance than 150 mm.
Ensure that the hear th (super imposed or
constructional) is suitably delineated to discourage
combustible oor nishes from being laid too close to
the appliance, by marking the edges or providing a
change of level.
Position the appliance on the hearth such that
combustible marerial cannot be laid closer to the base
of the appliance than :
(a) At the front, 300 mm if the appliance is an open
re or stove which an, when opened , be operated as
an open re, or 225 mm in any other case ;
(b) At the back and sides, 150 mm or in accordance
with the recommendations below which relate to
distance from hearth to walls. Please refer to section J
of the Building regulations.
When using a single wall ue pipe, there must be a
clearance (A) of at least 450 mm from any combustible
materials (timber mantel, girder).
Figure 4 - Smoke exit on the top
1 - Flue bafe
2- Back panel
3- Gasket
4- Blanking plate
5- Clamp
6- Gasket
7- Flue collar
Figure 5 - Smoke exit at rear

Monaco - 134 06 05
6 Technical manual "1303"
2.3 Mounting the ue collar
The stove is supplied with a connection ue spigot with
an inner diameter of 125 mm and an outer diameter
of 139 mm.
2.4 Smoke exit on the top
Figure 4
- The stove is set from the factory with a top outlet.
- Do not remove the cast iron top.
- Remove the cardboard chock from the top (A).
2.5. Smoke exit at rear
Figure 5
- Do not remove the cast iron top.
- Remove the cardboard chock from the top.
- Remove the infernal bafe 1.
- Removed the ue spigot 7.
- Place the seal rope 3 within the groove, x the
blanking plate 4and the clamp 5and ensure a good
tightness.
- Place the seal rope 6within the groove, screw into
position the spigot 7and ensure a good tightness
- Ret the ue bafe 1.
2.6 Flue
Existing ue : The chimney must comply with Current
Building Regulations. If in doubt, consult your Dealer
or local Building Inspector.
• The ue must be in good condition and must provide
sufcient draught (refer to technical details p. 3).
• The ue must be suitable for the installation of fuel
burning appliances, otherwise it must necessary to
install a tubing.
• The ue must be clean. It should be swept to remove
soot and dislodge tar deposits.
• The ue must be well insulated. If the ue inner wall
surfaces are cold, a good thermal draw is impossible
causing condensation problems (tar formation etc) to
occur.
• The ue must be watertight.
• The ue must not be shared with other appliances.
• The chimney must have a constant cross section.
• When the cross-section of the chimney is too large, it
has difculties in obtaining a good draught.
• The chimney must be at least 4.5 m (15 ft) high and
be at 40 cm above the ridge of the roof and 8 meters
away from any construction.
• In case of a at roof or when the roof gradient is
lower than 15°, the stack must be 1,2 m (4 feet) high
at least.
• The capping must not restrain the draught.
• If the chimney has any down draught tendency, due
to its position in relation to nearby obstacles, then
an anti-down draught cowl must be installed on the
chimney or the chimney height must be increased.
• If the chimney draught is excessive or irregular,
a draught stabilizer (barometric damper) must be
installed to the connector pipe it must be visible and
accessible.
Chimney to be built / New ue : The chimney
1 - Chimney
2 - Funnel-shape reproof material.
3 - Non-combustible plate
4 - Access to cleaning
5 - Insulation
6 - Plate not removable and ventilated air
Figure 6 - Chimney connector

Monaco 134 06 05
Technical manual "1303" 7
must comply with Current Building Regulations. If in
doubt, consult your Dealer or local Building Inspector.
• The appliance must not support the weight of the
ue.
• It must be distant from any combustible material
(walls, cross members)
• It must permit easy sweeping.
2.7 Chimney connector
• The connection to the ue must be carried out
according to local building regulations.
• The appliance must be installed as close as possible
to the chimney.
• Any connection pipe must be suitable for use with
solid fuel burning appliances in accordance with
Approved Document J of the building regulations.
• The connecting pipe must not reduce in diameter at
any point to less than the diameter of the outlet of the
stove.
• The connection can be either vertical or horizontal.
For horizontal connections, avoid right angle bends.
• The join between the connection pipe and the
stovepipe, and the ue, must be leak tight.
• For the premises equipped with a mechanical
controlled ventilation, the airtightness has to prevent
the exhauster drawing out the smokes from the
exhaust gas pipe.
• The connection pipe and any draught stabiliser must
have access for cleaning.
2.8. Door closing pressure
Figure 7
The closing latch rotates around a pressure screw
positioned cam.
- Loosen pressure screw 1,
- Turn cam to desired position. 2,
- Tighten pressure screw 1.
2.9 Pre-utilisation check
Check that the seals of the smoke-line are in good
condition. Check that the door closes correctly.
Check that the glass is not damaged. Check that the
smoke passages are not obstructed by packaging or
removable parts. Check that all removable parts are
correctly installed.
2.10 Maintenance of the Chimney
Very important : In order to avoid any incident
(chimney re, etc...), maintenance tasks must be
carried out regularly. If the appliance is regularly used,
the chimney should be swept several times per year,
together with the stovepipe connection section.
If the chimney catches re, you must cut off
the ue draught, close the doors and windows,
hatches and keys and call the Fire Brigade
without delay.
DO NOT OPEN THE DOOR OF THE APPLIANCE
(OR AIR INLET) UNDER ANY CIRCUMSTANCES
Chimney condition should be checked at least once
per year by a professional engineer.
1Pressure screw 2Cam
Figure 7 - Adjusting of the door closing pressure

Monaco - 134 06 05
8 Technical manual "1303"
3. Instructions for user
Don’t run the stove inmild weather with coal
: Under certain circumstances (e.g. fog and
repeated thaw) the chimney will not draw
sufciently well and thus be at the origin of
asphyxia.
Awaiting better weather circumstances, don’t
use any coal but only wood.
At the rst lighting, the re must be progressively
increased to allow the various parts to expand normally
and to dry up.
Note : When the re is lit for the rst time, the stove
may give off fumes from the new paint. This is normal
but ensure the room is well ventilated during the rst
few hours of operation.
Warning : properly installed and operated this
appliance will not emit fumes into the dwelling.
Occasional fumes from de-ashing and re-fuelling may
occur. Persistent fume emission is dangerous and must
not be tolerated. If fume emission does persist : Open
doors and windows to ventilate room.
Let the re go out and dispose of fuel from the
appliance.
The manufacturer will not be responsible for
any damage caused to the appliance due to the
incorrect use or installation of the appliance e.g.
prohibited fuel use and any alterations made to
the appliance which have not been authorised by.
the manufacturer. We recommend that you use
only the manufacturer's own brand spare
parts.
Figure 8 * Operating devices
B2
B1
A: Opening/closing the main door
B: Secondary air inlet)
B1 : opened
B2 : closed
C: Primary air inlet :
Opened : + / Closed : -
D: Handle
E: Tertiary air inlet
** We recommend that the wooden
operating handle is removed from
the door immediately After use and
set aside due to the fact that Wood
is a combustible material.
The Woodenhandle should never be
left on a lit appliance.
C
B
D
A
+
-
Coal Wood
Closed Opened
E
B

Monaco 134 06 05
Technical manual "1303" 9
Check for ue or chimney blockage, and clean if
required. Do not attempt to relight the re until the
cause of the fume emission has been identied and
corrected. If necessary seek expert advice.
Note : It is recommended to use a reguard in the
presence of children, and also in the presence of old
and/or inrm people.
3.1 Fuel
This appliance is not an incinerator.
Use hard wood logs, which have been cut for at least
two years and stored, under a ventilated shelter.
Use hardwood that have a higher caloric value per
cu metre (Yoke-elm, oak, ash, maple, birch, elm,
beech, etc.). Large logs must be split and cut to an
useful length, before being stored in a sheltered and
ventilated place.
• Recommended fuel :
The best fuels for use with the Franco Belge “Monaco”
are :
Seasoned wood. - hard wood logs that have been cut,
split and stored for at least two years with a maximum
moisture content of 20 % e.g. oak, beech, elm etc.
Anthracite – dry steam coal fuels as described in type
A – table B2 of the Standard – smokeless fuels such as
homere, phurnacite, ancit.
We do not recommend the use of Homere on your
stove due to the number of glass panels which have
been effected by this fuel.
• Prohibited fuel :
Any form of housecoal (bituminous coal) or petroleum
based fuels.
We do not allow that unseasoned wood (green wood)
is used due to it’s high levels of moisture which will
produce tar and in turn can cause the insides of the
stove and the lining of the chimney to become coated
which in turn could lead to a chimney re.
We do not allow recovered wood e.g railway
sleepers,chipboard, pallets are burned as these have
been treated and will product a great deal of pollution
to the environment and will overheat the appliance.
3.2. Instruction for use with Wood
Figure 8
3.2.1. Lighting
Set all air controls to the maximum opening. Use a
double handful of kindling and light the re with
chemical relighters with the door 5-10 mm ajar.
After several minutes the ames from the rebed are
diminishing, add 2 half-sized logs and keep the door
ajar and the air controls unaltered.
About 12 minutes from the Start, when the logs are
well alight but ames Start receding, add 2 full sized
logs and leave the controls as before.
After a further 3 mn, close the door wait for another
3 mn and close the primary air (C) until the logs burn
down to embers, reload a this point and adjust the
settings to the desired positions.
Never use relighters under liquid forms as
they may lead do severe safety issues.
3.2.2. Refuelling procedure
- The appliance must function with the door property
closed, the burning rate beign controlled in using the
secondary air ap (B).
Experience will show you which settings are best for
your situation.
Before refuelling, set the secondary air (B) to the
required setting, open at maximum the primary air
(C), load the Wood and wait for 3 or 4 minutes.
After This period, when the fuel logs are well blackened
and the ances well established close the primary air.
The airwash system works with the top airslide
(secondary air inlet B). When the top airslide is fully
opened the system works at is strangest efciency.
The more closed down the air slide is the less effective
the airwash will be (when shut down completely, the
airwash system can not function).
The nominal output is obtained with the settings as
follows :
- primary air inlet (C) - Closed
- secondary air inlet (B) - 50 % Open
- Tertiary air inlet - Opened
- It is important to follow theses instructions in order
to active clean burning and to maximise the efciency
from the stove.
- Do not leave the re unattended After on the new
charged logs.
- Always refuel on to hot embers.
- Never overload the rebox. Always keep the logs
below the level of the tertiary air holes.
3.3. Operating procedure when using
solid mineral fuels (smokeless fuels)
- When using smokeless fuels the tertiary air should
be closed (coal position) as the secondary air inlet (B).
The nominal output is obtained with the air settings
as follows :
- primary air (C) : 75 % opened
- secondary air (B) : closed
- tertiary air (E) : closed

Monaco - 134 06 05
10 Technical manual "1303"
3.5. De-ashing
- Ashes must be removed regularly.
- Ashes must never be allowed to pile up to the grate.
The grate would not be cool down and could rapidly be
damaged.
- Empty the ashes when the appliance is cold.
- Remove the ash drawer using the tool provided.
- Empty the ashes carefully with regard to the live
embers.
3.3 Maintenance of the Chimney
Very important ! In order to avoid any incident
(chimney re, etc...), maintenance tasks must be
carried out regularly.
If the appliance is regularly used, the chimney
should be swept several times per year, together
with the stovepipe connection section.
If the chimney catches re, you must cut off
the ue draught, close the doors and windows,
hatches and keys and call the Fire Brigade
without delay.
DO NOT OPEN THE DOOR OF THE APPLIANCE
(OR AIR INLET) UNDER ANY CIRCUMSTANCES.
The chimney must be serviced and cleaned by a
specialist.
3.6 Maintenance of the stove
• The appliance must be cleaned regularly , together
with the connecting pipe and the ue pipe.
• Open the door and remove all deposits in the rebox
and clean the removable re grate.
• Cleaning of the glass door can be done with a soft
cloth dampened with water and vinegar or potassium
; this must be done when the appliance is cold ; then
rinse with clear water. Do not use abrasive cleaners.
• The “vitroceramic” glass will resists to temperatures
of up to 750 C. Should the glass break due to misuse,
it must be replaced by the manufacturer own product.
• All the casing parts can be cleaned using a soft cloth
either dry, or slightly damp. In case of condensation or
water splashes clean the parts before they dry out.
• Check that there are no obstructions before relighting
after a long period of disuse.
• The appliance must not be used with a ue serving
several appliances.
• Keep the grates ventilation free of any obstructions.
3.7 Safety advice
This appliance produces heat and may cause severe
burns if touched.
The stove may still be HOT even when the re has
burnt out.
KEEP CHILDREN AWAY.
A FIRE GUARD IS ADVISABLE TO PROTECT
CHILDREN, THE ELDERLY AND INFIRM.

Monaco 134 06 05
Technical manual "1303" 11
3.8. Trouble Shooting
Problem Probable causes - ACTION
Fire difficult to start
Fire goes out
Wood green...or damp Use hard wood logs, which have been cut for at
least two years and stored, under a ventilated
shelter.
Logs are too big. - To light the fire, use small, very dry twigs. To
maintain the fire, use split logs.
Poor quality wood - Use hardwood that have a higher calorific
value per cu metre (Yoke-elm, oak, ash, maple,
birch, elm, beech, etc.)
Not enough primary air - Open air control.
Insufficient draught - Check that the flue is not obstructed, sweep
it if necessary
- Seek advice from a chimney specialist.
Fire burns too quickly. Too much draught - Partially close the top air control.
Excessive draught. - Install a draught stabiliser to the connector
pipe. Consult your Dealer.
Poor quality wood. - Do not continuously burn small wood, sticks,
bundles, carpentry offcuts (plywood, pallets),
etc.
Smokes when lighting up. Flue duct is cold. - Burn paper and kindling wood to increase
heat.
Room is in decompression (negative
pressure)
- In houses equipped with mechanical
ventilation, partly open a window until the fire
is well established.
Smokes while burning. Draught is insufficient. - Consult a chimney specialist.
- Check that the flue is not obstructed, sweep if
necessary.
Down draught. - Install an anti-down draught cowl. Consult
your Dealer.
Room is in decompression. - In houses equipped with Mechanical
Ventilation, partly open a window until the fire
is well established.
Low heat output. Poor quality wood. - Use hardwood that have a higher calorific
value per cu metre (Yoke-elm, oak, ash, maple,
birch, elm, beech, etc.)
Poor mixing of the convection air - Check the air flow system (air inlet, piping,
air outlet).
- Check that the next rooms are equiped
with ventilation grids to help out the hot air
circulation.
: : This sign means that you should
ask for a qualified engineer
to do the work.

Monaco - 134 06 05
12 Technical manual "1303"
4. Spare parts
When ordering spare parts, specify the stove type and serial number, including the colour index (on the
guarantee or identication plate), the name of the part and the part number.
Example : Wood stove "Monaco”, ref. 134 06 05 color P, top plate 352175 RH
Y= 1340605 Y ; P= 1340605 P ; L= 1340605 L ; E= 1340605 E ; J= 1340605 J
N° Code .................................. Description ............................ Type........... Y.........P......... L........ E......... J................... Qty
1 100917 .................................. Axle...................................... 12x20 M7........ Y......... P......... L.........E..........J..................... 1
2 100939 .................................. Axle............................................................. Y......... P......... L.........E..........J..................... 3
3 100964 .................................. Axle............................................................. Y......... P......... L.........E..........J..................... 2
4 101067 .................................. Axle............................................................. Y......... P......... L.........E..........J..................... 1
5 102042 .................................. Firebrick....................................................... Y......... P......... L.........E..........J..................... 2
6 102044 .................................. Firebrick....................................................... Y......... P......... L.........E..........J..................... 2
7 105006 .................................. Gasket ......................................................... Y......... P......... L.........E..........J................. 1,65 m
8 134758 .................................. Pin ...........................................4x16 ........... Y......... P......... L.........E..........J..................... 1
9 142881 .................................. Gasket ......................................................... Y......... P......... L.........E..........J..................... 2
10 158637 .................................. Handle......................................................... Y......... P......... L.........E..........J..................... 1
11 179628 .................................. Regulator shaft............................................. Y......... P......... L.........E..........J..................... 2
12 181614 .................................. Gasket ........................................................ Y......... P......... L.........E..........J................. 1,04 m
13 181632 .................................. Gasket ......................................................... Y......... P......... L.........E..........J................. 1,35 m
14 181633 .................................. Gasket ......................................................... Y......... P......... L.........E..........J................. 1,58 m
15 188858 .................................. Ceramic glass ............................................... Y......... P......... L.........E..........J..................... 1
16 189104 .................................. Screw .......................................................... Y......... P......... L.........E..........J..................... 2
17 204209 00 .............................. Supplementary plate..................................... Y......... P......... L.........E..........J..................... 1
18 224022 00 .............................. Ash-pan ....................................................... Y......... P......... L.........E..........J..................... 1
19 228624 00 .............................. Square......................................................... Y......... P......... L.........E..........J..................... 1
20 231304 00 .............................. Square......................................................... Y......... P......... L.........E..........J..................... 1
21 237430 00 .............................. Reducing plate ............................................. Y......... P......... L.........E..........J..................... 1
22 259015 00 .............................. Fixing plate .................................................. Y......... P......... L.........E..........J..................... 2
23 262614 00 .............................. Heat shield................................................... Y......... P......... L.........E..........J..................... 1
24 265606 00 .............................. Knob............................................................ Y......... P......... L.........E..........J..................... 1
25 265608 00 .............................. Knob............................................................ Y......... P......... L.........E..........J..................... 1
26 270402 00 .............................. Air control ap.............................................. Y......... P......... L.........E..........J..................... 1
27 270417 00 .............................. Air control ap.............................................. Y......... P......... L.........E..........J..................... 1
28 300136 RH ............................. Leg.......................................................................... P........................................................ 4
28 300136 RP.............................. Leg..................................................................................................E................................. 4
28 300136 77 .............................. Leg...................................................................................... L............................................ 4
28 300136 79 .............................. Leg..............................................................................................................J..................... 4
28 300136 EF .............................. Leg.............................................................. Y.................................................................... 4
29 300432 EF .............................. Base ............................................................ Y......... P......... L.........E..........J..................... 1
30 301537 71 .............................. Door lock ..................................................... Y......... P......... L.........E..........J..................... 1
31 303718 RH ............................. Blanking plate .......................................................... P........................................................ 1
31 303718 RP.............................. Blanking plate ..................................................................................E................................. 1
31 303718 77 .............................. Blanking plate ...................................................................... L............................................ 1
31 303718 79 .............................. Blanking plate ..............................................................................................J..................... 1
31 303718 EF .............................. Blanking plate .............................................. Y.................................................................... 1
32 303860 RH ............................. Flue collar ................................................................ P........................................................ 1
32 303860 RP.............................. Flue collar ........................................................................................E................................. 1
32 303860 77 .............................. Flue collar ............................................................................ L............................................ 1
32 303860 79 .............................. Flue collar ....................................................................................................J..................... 1
32 303860 EF .............................. Flue collar .................................................... Y.................................................................... 1
33 306296 EF .............................. Back wall ..................................................... Y......... P......... L.........E..........J..................... 1
34 307424 EF .............................. Full retainer.................................................. Y......... P......... L.........E..........J..................... 1
35 309232 .................................. Wood grate .................................................. Y......... P......... L.........E..........J..................... 1
36 310733 RH ............................. Side panel................................................................ P........................................................ 1
36 310733 RP.............................. Side panel........................................................................................E................................. 1
36 310733 77 .............................. Side panel............................................................................ L............................................ 1
36 310733 79 .............................. Side panel....................................................................................................J..................... 1
36 310733 EF .............................. Side panel.................................................... Y.................................................................... 1
37 310833 RH ............................. Side panel................................................................ P........................................................ 1
37 310833 RP.............................. Side panel........................................................................................E................................. 1
37 310833 77 .............................. Side panel............................................................................ L............................................ 1
37 310833 79 .............................. Side panel....................................................................................................J..................... 1
37 310833 EF .............................. Side panel.................................................... Y.................................................................... 1
38 315615 .................................. Air duct........................................................ Y......... P......... L.........E..........J..................... 1
39 323209 .................................. Flue bafe.................................................... Y......... P......... L.........E..........J..................... 1
40 324503 .................................. Sealing plate ................................................ Y......... P......... L.........E..........J..................... 1
41 326605 .................................. Suppl. ue bafe .......................................... Y......... P......... L.........E..........J..................... 1
42 327909 RH ............................. Ash pan guide .......................................................... P........................................................ 1
42 327909 RP.............................. Ash pan guide ..................................................................................E................................. 1
42 327909 77 .............................. Ash pan guide ...................................................................... L............................................ 1

Monaco 134 06 05
Technical manual "1303" 13
Figure 9 - Stove - exploded view
37
5
6
40
21
3
3
26
11
1
30
4
8
10
19
43
42
20
2
24
16
16 34
15
22
9
38
39
6
6
27
33
35
18
5
36
29
28
23
25
32
45 2
31
17
13
46
47 48
7
12
13
14
12
44
49
41

Monaco - 134 06 05
14 Technical manual "1303"
Y= 1340605 Y ; P= 1340605 P ; L= 1340605 L ; E= 1340605 E ; J= 1340605 J
N° Code .................................. Description ............................ Type........... Y.........P......... L........ E......... J................... Qty
42 327909 79 .............................. Ash pan guide ..............................................................................................J..................... 1
42 327909 EF .............................. Ash pan guide .............................................. Y.................................................................... 1
43 331116 RH ............................. Main door ................................................................ P........................................................ 1
43 331116 RP.............................. Main door ........................................................................................E................................. 1
43 331116 77 .............................. Main door ............................................................................ L............................................ 1
43 331116 79 .............................. Main door ....................................................................................................J..................... 1
43 331116 EF .............................. Main door .................................................... Y.................................................................... 1
44 332004 .................................. Air duct........................................................ Y......... P......... L.........E..........J..................... 1
45 352175 RH ............................. Top plate.................................................................. P ........................................................ 1
45 352175 RP.............................. Top plate..........................................................................................E................................. 1
45 352175 77 .............................. Top plate.............................................................................. L ............................................ 1
45 352175 79 .............................. Top plate......................................................................................................J ..................... 1
45 352175 EF .............................. Top plate...................................................... Y.................................................................... 1
46 406816 .................................. Clamp.......................................................... Y......... P......... L.........E..........J..................... 1
47 808001 ED ............................. Hand tool..................................................... Y......... P......... L.........E..........J..................... 1
48 161025 .................................. Touch-up paint ..................................................................... L............................................ 1
48 161027 .................................. Touch-up paint .............................................................................................J..................... 1
48 161060 .................................. Touch-up paint ......................................................... P........................................................ 1
48 161061 .................................. Touch-up paint .................................................................................E................................. 1
49 989009 .................................. Complete door.............................................. Y......... P......... L.........E..........J..................... 1

Technical manual "1303" 15
Notes
Monaco - 134 06 05

Guarantee certificate
Legal guarantee
The specications, dimensions and information shown on our
documents are provided for information purposes only and
under no circumstances are binding upon the vendor.
With the aim of constantly improving our equipment, all
modications considered as necessary by our departments
may be made without notice.
The provisions of the present guarantee certicate are not
excluding or limiting the owner of the equipment’s rights,
concerning the legal guarantee regarding faults or hidden
vices which applies in all circumstances, in the conditions
detailed in articles 1641 and following of the civil code, and in
the country in which the equipment was purchased.
Contractual guarantee
Our equipment is guaranteed against faults and hidden
vices subject to the following conditions :
1) Installation and adjustment of the device by a professional
installer.
2) Observance of the instructions provided in our technical
documents and our installation/adjustment instructions.
3) The installation, use and maintenance of the device
carried out in conformity with the applicable standards and
legislation, and with the indications provided in the technical
instructions accompanying the device.
This guarantee covers the replacement, in our factory, of
parts recognised as being defective from the outset by our
“Guarantee Inspection” Department. Carriage and labour is
at the user’s cost. Moreover, if the repair or replacement of
parts covered by the guarantee is found to be too costly vis-
à-vis the price of the appliance, the decision to replace or
repair the appliance will be taken by the vendor.
Our guarantee is for 2 (two) years for all appliances, with
the exception of closed combustion replace and inserts for
which our guarantee is 5 (ve) years excluding the following :
1) Indicator lights, fuses, electrical elements and fans.
2) Parts subject to wear or in contact with high temperatures
namely: soles and burner grates, bottom plates bafes, ash
pans, paintwork and surface treatments for decorative parts.
Also excluded from this guarantee are seals and glass.
3) Any damage which may result from the use of the appliance
with a fuel other than that stipulated in our instructions.
4) Damage occurring to parts caused by elements outside the
appliance (down draught, storm damage, damp, abnormal
pressure or vacuum, heat shocks, etc.).
5) Damage to electrical parts caused by plugging in and
using the appliance on a mains system, the voltage of which
(measured at the entrance to the appliance) is 10% above or
below the nominal voltage of 220 V.
Exclusion of liability
In the case of a product manufactured at the client’s request,
under no ci rcumstances may we, as a subcontractor, be
considered liable vis-a-vis the client or third parties for
defects arising from the installation or a design fault with the
item in question.
Name and address of the installer : .........................................................................................................................
..............................................................................................................................................................................
Telephone : ............................................................................................................................................................
Name and address of the customer :.........................................................................................................................
..............................................................................................................................................................................
Date of installation :................................................................................................................................................
Model of the appliance :  134 06 05
Color :  Y  P  L  E  J
Serial number :..............................................
• This certicate has to be completed and kept carefully.
In case of claims, send a copy of this to :
FRANCO BELGE - BOUTIQUES DU FEU
Parc d'activités de la Verte Rue - Allée des Prêles - 59270 BAILLEUL - FRANCE