Monsoon MONS150RE Assembly instructions

MON-CONS
MONS150RE
Installation and Wiring Instructions
150mm AXIAL FAN REVERSIBLE
PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS.
PLEASE SAVE THESE INSTRUCTIONS.
IP45

2

3
Installation and Wiring Instructions for the MONS150RE Reversible Fan.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE
COMMENCING THE INSTALLATION
DO NOT install this product in areas where the following may be present or occur:
•Excessive oil or a grease laden atmosphere.
•Corrosive or flammable gases, liquids or vapours.
• Ambient temperatures higher than 40°C or less than –5°C.
• Possible obstructions which would hinder the access or removal of the Fan.
SAFETY AND GUIDANCE NOTES
A. All wiring to be in accordance with the current I.E.E.
Regulations, or the appropriate standards of your country
and MUST be installed by a suitably qualified person.
B. The Fan should be provided with a local isolator switch
capable of disconnecting all poles, having a contact
separation of at least 3mm.
C. Ensure that the mains supply (Voltage, Frequency, and
Phase) complies with the rating label.
D. The Fan should only be used in conjunction with the
appropriate Monsoon products.
E. The Fan should only be used in conjunction with fixed
wiring.
F. When the Fan is used to remove air from a room containing
a fuel-burning appliance, ensure that the air replacement is
adequate for both the fan and the fuel-burning appliance.
G. The Fan should not be used where it is liable to be subject
to direct water spray for prolonged periods of time.
H. Where ducted Fans are used to handle moisture-laden air, a
condensation trap should be fitted. Horizontal ducts should
be arranged to slope slightly downwards away from the Fan.
I. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
J. Children should be supervised to ensure that they do not
play with the appliance.

4
Open up the internal cover to access
the spirit level bubble and terminals
K. Stationary appliances not fitted with means for
disconnection from the supply mains having a contact
separation in all poles that provide full disconnection under
over voltage category III, the instructions state that means
for disconnection must be incorporated in the fixed wiring in
accordance with the wiring rules.
L. Ensure the grille is fully engaged onto the fan chassis using
all clips.
DESCRIPTION
MONS150RE axial extract/intake fan is suitable for domestic kitchens and utility rooms. They are
available as wall or panel mounted model and can be used in conjunction with Reversible speed
controller MON-RSCON supplied seperately.
INSTALLATION
IMPORTANT: The fan should only be used in conjunction with fixed wiring.
PANEL MOUNTING
1. For panel mounting the fan should be installed
into a duct protected by an exterior air grille that
must comply with the standard requirements of
your country to prevent access to the fan’s
impeller.
2. Cut a 155mm diameter hole for 150mm fans.
3. Push the two clips on the left and righthand side
of the fan and pull the grille away from the
chassis.
4. Using the built in spirit level bubble as an aid,
mark the screw centres through the holes in the
fan back plate. Drill, plug and screw into
position.
5. After installation, ensure impeller rotates freely
and the shutters can open.
6. Replace the grille and ensure the clips engaged.
WALL MOUNTING
1. For wall mounting cut a 170mm diameter hole for 150mm fans, through the wall and insert the
wall sleeve. Slope the sleeve slightly downwards away from the fan. Cut to length and cement
both ends into position flush with the wall faces.
2. Push the two clips on the left and righthand side of the fan and pull the grille away from the
chassis.
3. Using the built in spirit level bubble as an aid, mark the screw centres through the holes in the
fan back plate. Drill, plug and screw into position. Fix exterior grille into position with the louvres
positioned downwards. (Note:- The grille must comply with the standard requirements of your
country to prevent access to the fan’s impeller. The wall kit used in this installation should
provide a minimum ducting length of 100mm from the fans back plate to the inside of the
external grille).
4. After installation, ensure impeller rotates freely and the shutters can open.
5. Replace the grille and ensure the clips engaged.

5
WIRING & SETUP
WARNING: THE FAN AND ANCILLARY CONTROL
EQUIPMENT MUST BE ISOLATED FROM THE
POWER SUPPLY DURING THE INSTALLATION / OR
MAINTENANCE.
IMPORTANT
The fan should only be used in conjunction with fixed wiring.
The cross - sectional area of supply cord used should be ranged from 1 -1.5mm2.
Cable entry can only be made from the rear of the fan.
The fan is suitable for connection to 220-240V 50Hz supply.
The fan is a class ll double insulated product and MUST NOT be earthed.
1. Select and follow the appropriate wiring diagram. (Fig. 1,2 3 or 4)
2. Check all connections have been made correctly and securely fastened.
3. Ensure the impeller rotates and is free from obstructions.
SERVICING AND MAINTENANCE
WARNING: THE FAN AND ANCILLARY CONTROL
EQUIPMENT MUST BE ISOLATED FROM THE
POWER SUPPLY DURING MAINTENANCE.
1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there
is no build up of dirt or other deposits.
2. Wipe the inlets and front face with a damp cloth until clean.
The fan has sealed for life bearings, which do not require lubrication.

6
Fig.1: MONS150RE Wired as Extract fan only
Fig.2: MONS150RE Wired as Intake fan only
Fig.3: Wired with External Extract / Intake fan controller.

7
Fig.4: MONS150RE Wired with External fan control using additional accessory
MON-RSCON – Reversible speed controller.

8
Disposal
This product should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority for recycling advice
NationalVentilation
StatheRoad
Burrowbridge
Somerset
TA70RY

Website:www.nationalventilation.co.uk
email:[email protected]
Salesandtechnicalhotline:01823690290
495804A 0420