Monstertech STAND User manual

STAND
Instruction Manual EN

STAND INSTRUCTION MANUAL
2
1 General information
Congrats on your brand new MONSTERTECH Stand!
This guide is meant to help you assemble your Stand as smoothly as possible. If you still have
questions about the assembly process, please contact [email protected] or support@
monstertechusa.com.
1.1 Before you start
Before you start the Stand assembly, we are going to look at some common assembly steps
and often used parts, as well as required tools.
1.1.1 Required Tools
For our Stand assembly, we need the following tools*:
- Hex key set with ball head with extension
- Rubber or plastic mallet
- Flat head screwdriver
- Tape measure w/ millimeters
*Tools are not included with the Sim Rig

STAND INSTRUCTION MANUAL
3
1.1.2 Inserting T-Nut into Profile
There are two ways to insert the M8 T-Nuts into the respective prole groove; refer to Figure 1
and 2 respectively.
Figure 1: Slide in from side
Figure 2: Rotate in from top

STAND INSTRUCTION MANUAL
4
1.1.3 Universal Fastener Assembly
The universal fastener assembly can be prepared the following way, so long as the T-Nut can
be slid in from the side. One Universal Fastener Assembly is made up from one (1) M8x30 Hex
Screw, one (1) T-Nut, and one (1) Universal Fastener.
Figure 3: Universal fastener assembly
If inserting the universal fastener assembly from the side is not possible, it is necessary to rota-
te the T-Nut into the prole groove rst, and then screw the M8x30 bolt (along with the univer-
sal fastener) into the T-Nut.

STAND INSTRUCTION MANUAL
5
1.1.4 Angle Bracket Stud Removal
Sometimes it might be necessary to break off the studs from angle brackets (if those are part
of the product). This is best achieved by:
1. Inserting a at-head screwdriver between the stud and the bracket, and then
2. Rotate the screwdriver for the stud to come off

STAND INSTRUCTION MANUAL
6
1.1.5 Angle Bracket Assembly
For some assemblies the use of angle brackets is required. These are prepared by using two
(2) M8x18 hex screws, two (2) washers, and two T-Nuts.
Figure 5: Angle bracket assembly
1.1.6 Adjustment of Profile Feet
The prole feet are installed on the MTX Base Stand, MTX Stand-Alone TV or Stand.
Figure 6: Prole feet

STAND INSTRUCTION MANUAL
7
2 Overview
2.1 Completed Stand
Stand - Overview
Figure 8: Complete Stand
Use the above image as reference for the following Stand assem-
bly instructions.

STAND INSTRUCTION MANUAL
8
3.1
Figure 9: Stand assembly - step 1
3.2
Figure 10: Stand assembly - step 2

STAND INSTRUCTION MANUAL
9
3.3
Figure 11: Stand assembly - step 3
3.4
Figure 12: Stand assembly - step 4

STAND INSTRUCTION MANUAL
10
3.5
Figure 13: Stand assembly - step 5
3.6
Figure 14: Stand assembly - step 6

STAND INSTRUCTION MANUAL
11
3.7
Figure 15: Stand assembly - step 7
3.8
Figure 16: Stand assembly - step 8

STAND INSTRUCTION MANUAL
12
3.9
Figure 17: Stand assembly - step 9
3.10
Figure 18: Stand assembly - step 10

STAND INSTRUCTION MANUAL
13
3.11
Figure 19: Stand assembly - step 11
Your Completed MONSTERTECH Stand
Figure 20: Stand assembly - step 12

STAND INSTRUCTION MANUAL
14
4 Pedal Mount (optional)
Figure 25: Pedal mount

STAND INSTRUCTION MANUAL
15
4.1
Figure 26: Pedal mount assembly - step 1
4.2
Figure 27: Pedal mount assembly - step 2

STAND INSTRUCTION MANUAL
16
4.3
Figure 28: Pedal mount assembly - step 3
4.4
Figure 29: Pedal mount assembly - step 4

STAND INSTRUCTION MANUAL
17
4.5
Figure 30: Pedal mount assembly - step 5
4.6
Figure 31: Pedal mount assembly - step 6

STAND INSTRUCTION MANUAL
18
4.7
Figure 32: Pedal mount assembly - step 5
4.8
Figure 33: Pedal mount assembly - step 6

STAND INSTRUCTION MANUAL
19
4.9
Figure 34: Pedal mount assembly - step 7
Your Completed Stand with Pedal Mount
Congratulations! You’re all done with your MTX Stand!

WARNHINWEISE
VORSICHT! Achten Sie darauf, dass die
Lenkradwinkelverstellung nach dem Einstellen wieder fest
angezogen ist.
GEFAHR: Nicht für Kinder unter 3 Jahren,
Kleinteile - Verschluckungsgefahr!
Nur für Kinder ab 12 Jahren und Erwachsene
Alle MONSTERTECH Produkte sind handgefertigt und
qualitätsgeprüft.
Das Rennsitzgestell ist zur Verwendung in Kombination mit
einem Autositz und nur zur Verwendung im Innenbereich
ausgelegt.
Wir übernehmen keine Haftung für zweckentfremdete
Benutzung.
Bei Fragen zur Sicherheit oder Aufbau des Rennsitzgestells,
wenden Sie sich an inf[email protected] oder besuchen
unsere Website unter www.monstertech.de.