Montezuma MPSO-4B User manual

OWNER'S MANUAL
4-BAY
POWER TOOL
ORGANIZER
MPSO-4B
www.montezumastorage.com

2
LIFE ORGANIZED
Montezuma is committed to helping you succeed in both your work
and personal life by being organized, prepared and equipped with
the right tools, gear and home supplies at your finger tips.
Keep your life organized with Montezuma.
Thank you for your purchase of this Montezuma Power Tool Organizer.
ATTENTION
TO REDUCE THE RISK OF INJURY, THE USER MUST READ AND
UNDERSTAND THIS INSTRUCTION MANUAL BEFORE USING THIS
PRODUCT FOR THE FIRST TIME. SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
Fill in the following information and retain
this owner's manual for future reference:
MODEL(S):
DATE OF PURCHASE:
PLACE OF PURCHASE:
RECEIPT NO:

3
SPECIFICATIONS
MAXIMUM WEIGHT FOR POWER TOOL BAYS: 5 lb (2.3 kg)
MAXIMUM WEIGHT FOR TOP AND MIDDLE SHELVES: 20 lb (9.1 kg)
OVERALL DIMENSIONS:
17-3/4" W x 9-1/2" D x 3-3/8" H (45 cm W x 24 cm D x 8.5 cm H)

4
PARTS LIST
To order replacement parts, email [e-mail] or call 1-800-459-4409
(Monday–Friday, 8:00 am–4:30 pm, CST). Have the part number and quantity ready.
Not all parts are covered under warranty. Those parts not covered can be purchased.
REF DESCRIPTION PART NUMBER QTY
1Nut 122260 15
2Bolt 122261 15
3Self Tapping Screw 122262 4
4Plastic Drywall Anchor 122263 4

5
Nut
For use with bolts
Plastic Drywall Anchor
For use with the self tapping screws
Bolt
For assembling the power tool organizer
Self Tapping Screw
For attaching the power tool
organizer to a wall or a pegboard
15 15
44

6
TOOLS REQUIRED
Phillips head screwdriver
Socket wrench
Power drill
Level
A S S E M B LY
Attach the two side panels to the bottom
panel using two bolts and nuts per side.
Note: the tabs on the front of the power tool
slots should face down.
Attach the two side panels to the middle
shelf using two bolts and nuts per side.
Note: the holes in the edge of the shelf
should face forward.

7
Attach the two side panels to the top shelf
using two bolts and nuts per side.
Note: the flange on the top shelf should face
downward.
Position the support bar so the slot passes
through the tab on the bottom shelf with the
power tool slots. Secure the bar by lining
up the hole at the top of the support bar
with the corresponding hole on the middle
shelf. The support bar should be positioned
behind the front edge of the middle shelf.
Secure using a bolt and nut.

8
INSTALLATION
This organizer is built for 16" on center wall
studs. Locate the wall studs and mark the
locations of the four holes shown in the
illustration. Use a level to make sure the
organizer is straight.
Pre-drill pilot holes into the wall studs.
Secure the self-tapping screws into the
marked locations, leaving enough room to
position the organizer in place using the
keyhole slots.
Then tighten down the screws to secure the
organizer in place.
Note: To secure into dry wall, use the plastic
drywall anchors. For safety and security, the
organizer should be mounted into at least
one stud wall.
7"
16"

9
This product is warranted to be free from defects in materials
and workmanship for a period of one (1) year from the date
of original purchase.
If this product is defective, email [e-mail]
or call 1-800-459-4409 (Monday–Friday, 8:00 am–4:30 pm, CST). If the
product is defective, we will replace the defective part at no cost to you.
Please do not ship your product back to the store or to us
unless we send you written instructions for return.
In the event it becomes necessary for your product
to be returned, we will notify you how to proceed.
A copy of your original purchase receipt must accompany
the returned product.
1

M P S O4 B _11/19
Manufactured by:
QUALITY CRAFT
Romeoville, IL 60446
[e-mail]
1-800-459-4409
(Monday to Friday, 8:00 am–4:30 pm, CST)
Made in China
www.montezumastorage.com