Mountup MU0014 User manual

Measure and note the width and the height
of the square or rectangle formed from the
VESA holes pattern .
01 02
TV PlateWall Plate Extenders
Nuts Bolts
3B
3A
x2
x1x1 x2
4A
x8
4B
x8
Step 2 Mesure your TV pattern
W
H
2M2M
100mm ≈4in.
130mm≈5 1/8in.
200mm ≈8in.
300mm ≈11 3/4in
340mm ≈13 3/4in.
400mm≈16in.
Select the configuration A , B , C, D, or E to use based on the measurement from STEP 2.
for VESA hole pattern:
100x100mm, 130x130mm,200x100mm, 200x200mm.
200 mm
100 mm
130 mm
200 mm
100 mm
130 mm
A
VESA Pattern
(WxH) Configuration VESA Pattern (WxH) Configuration
100mm x 100mm A 300mm x 200mm C
130mm x 130mm A 300mm x 300mm E
200mm x 100mm A 400mm x 200mm C
200mm x 200mm A 400mm x 300mm D
200mm x 300mm B 400mm x 400mm E
200mm x 400mm B
Hardware Included
Max:400x400mm/16x16"
Min:100x100mm /4x4"
26"~55"
(V4)
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4x4
Philips Screws
M8 x 25mm
M8 x 45mm
x4
x4 x8 x4
Spacers
L5mm
x8
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
M6M4 M8
Correct Correct
Too Long
Too Short
Step 1-2 Select TV screw length
Max:
(40KG)
88LBS
Safety Caution
Must Check Before Getting Started
Installation Tools (Not Included)
Band
Tape
2M
Socket
Wrench
ScrewdriverPencil Electrodrill
Stud
Finder
HammerAwl Wood
Drill Bit
Masonry
Drill Bit
Wood Stud Installation Concrete Installation
1/2"
(13mm)
3/8"
(10mm)
7/32"
(5.5mm)
Step 3-1 Select monitor plate configuration Step 3-2 Assemble TV plate and extenders
Velcro Cable Ties ×5 Bubble Level ×1
When attaching brackets to the flat screen, be careful not to over tighten screws and
be sure that screws do not bottom out in the mounting holes.
MAX:400mm/16"
MAX:
400mm/16"
Min. 8"
(203mm)
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
Max:
(40KG)
88LBS
Min. Wood Stud Size:
nominal 2”(51mm)
actual 1 1/2”(38mm)
Min. Wood Stud Size:
nominal 4”(102mm)
actual 3 1/2”(89mm)
<16mm(5/8")
Drywall with wood studs
Hardware （Wall /Product)
Lag Bolts 5/16 x 2½ in
x3 x1
BA
Open-end wrench
MU0014 INSTALLATION INSTRUCTION
If you have any questions, please contact us.
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the installation, assembly
or use of this product, please contact us.
●This product is designed for use in wood stud and solid concrete wall.
- DO NOT install into drywall alone.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
● Do not apply this product to any purpose not indicated by MOUNTUP.
● Incorrect installation may result in product damage or body injury. MOUNTUP shall bear no responsibility
for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,
please contact us.
For VESA:
300x300mm, 400x400mm
For VESA:
400x300mm
DE
For VESA:
400x200mm, 300x200mm
C
For VESA:
200x300mm,
200x400mm
B
200 mm
400 mm
300 mm
200 mm
400 mm
300 mm
400 mm
300 mm
400 mm
400 mm
300 mm
300 mm
If your TV hole pattern is greater than 200x200mm, attach extenders [3A] and [3B] to TV plate
[02] using Nut [4A] and Bolt [4B].
M-A
Use the shorter screws
M-B
M-C
M-E
Not for M8 screws
Use the longer screws
Not for M8 screws
M-FM-D
(b) For Round Back / Extra Space
6A
6B
B
3B
3B
3A
3A
3A
6A 6B
3B
M-A
M-B
M-C
M-E
Top of TV
Top of TV
02
Step 3-3 Attach the brackets
(a) For Flat Back
No!
No!
4
1 2
43 5

Step 4A Wall plate installation (wood stud)
4A-1
4A-2
Locate your studs. Verify and mark the center of the stud
by finding the stud edges using an awl, a thin nail, or an
edge-to-edge stud finder.
Position the wall plate at your desired height and
line up the holes with your stud center line. Level the
wall plate and mark the pilot hole locations.
01
4A-3
Drill pilot holes using a 7/32 in. (5.5mm) diameter drill bit.
IMPORTANT:
Pilot holes must be drilled to a depth
of 2 3/4 in (70 mm). Be sure to drill into the center of thestud.
7/32 in
Ø5.5 mm
4A-4
01 A
Install wall plate using lag bolts .
Tighten the lag bolts until they are
pulled firmly against the wall plate .
01
A
01
A
UP
01
Position the wall plate at
your desired height, level the
wall plate and mark the pilot
hole locations x3.
4B-1
Step 4B Wall plate installation (concrete or brick)
Drill pilot holes
4B-2
4B-3
A
Concrete Wall
Concrete Wall
Contact us to have these additional pieces shipped
directly to you.
Concrete wall anchor 3pcs (NOT INCLUDED)
Ø10*61mm
01 A
01
Install wall plate using lag bolts
and anchors (not included).
Tighten the lag bolts until they are
pulled firmly against the wall plate .
A
01
UP
Lift and hang TV assembly onto arm and wall plate.
Secure the monitor plate to the arm and wall
plate with the removed screws and washers
from the previous step.
Step 5 Lift and hang TV with brackets onto wall bracket
Remove 2 preassembled screws
and washers, save them for using
to next step.
Tool-free Tilting Adjustment
-10°
+5°
Tighten
Loosen
B
If necessary
If TV keeps tilting down, Pull TV to
desired angle then fasten tilting nuts
with open-end wrench.
Adjustments
Loosen the screws Level the TV
± 3°
Leveling adjustment (-3°/+3°)
If needed, TV can be leveled ±3 degrees via adjusting the 2 screws with the open-end wrench.
B
Tighten the screws
B
Product dimensions:
Bubble Level
2.75in (70 mm）
Ø 10 mm
Ø 10 mm
3/8in
2.75in (70 mm）
No!
No!
No!
400mm/15.7"
200mm/7.9"
100mm/3.9"
100mm
/3.9"
426.5mm/16.8"
Φ6.9mm/0.3"
Φ8.9mm/0.4"
484mm/19"
30mm/1.2"
40mm/1.6"
Φ20mm/0.8"
432mm/17"
206mm/8.1" 206mm/8.1"
52mm/2"
225mm/8.9"
101mm/4"
100.5mm/4"
30.9mm/1.2"
58mm/2.3"
Φ9mm/0.4"
69mm/2.7"
20mm/0.8"
400mm
/15.7"
200mm
/7.9"
427mm
/16.8"
01
Bubble Level
01
UP
UP
+5°
-10°
8
10 11
7
4
76 8
109 11