Mountup MUA6007B User manual

Product Dimensions
Supplied Parts and Hardware
E1
Bolt Y
E4
Clip Plate
All are included in E
NOTE: Not all parts and hardware included will be used.
E2
Bolt
E3
Washer
F (×1)
VESA Plate
INSTALLATION INSTRUCTION
CX03-01_V1.0
Safety Caution
If you have any questions, please feel free to contact Customer Service
via Amazon before returning.
BEFORE ASSEMBLY
● Please check and make sure all necessary accessories are included and undamaged.
● Please read and understand this manual carefully before installation.
WARNING
● This product contains small items that could be a choking hazard if swallowed.
KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
● Improper installation, such as using the product for monitor over its load capacity or for any
purpose not explicitly specified, may cause damage or serious injury. We would not be liable for
any damage or injury caused by improper mounting or inappropriate use.
CAUTION AND MAINTENANCE
● Never allow children to climb, stand, hang, or play on any part of monitor or stand.
● This product is intended for indoor use only. Using this product outdoors could lead to product
failure and personal injury.
● Check that the bracket is secure and safe to use at regular intervals (at least every three months).
0.39~3.35" (10~85mm)
C-clamp Φ0.39~2.36"
(Φ10~60mm)
0.39~2.76" (10~70mm)
Grommet
Verify Your Desk Specifications:
Must Check Before Getting Started
Perfect!
Perfect!
Verify Your Monitor Specifications:
WARNING:
Gas Spring Arm is under pressure and should be handled with care.
Failure to follow the instructions may result in damage to the mount and/or personal injury.
Tension adjustment should be done only
after monitor installation
VESA Pattern (W × H):
75mm × 75mm / 3" × 3"
100mm × 100mm / 4" × 4"
cm
inches
W
H
4.4~19.8 lbs
(2~9 kg)
Load
Capacity
B-2
Attach the clamp (E) to the brace (D). Then tighten the bolts (M) with 4mm Allen key (I).
A-2
Detach the clip plate (E4) from the clamp (E).
Base Installation
1-B
Base Installation
1-A
If existing grommet hole comes with a plastic protector, remove it to ensure a flat
surface before installing the desk mount.
Run carriage bolt (O) with base (C) through grommet hole on desktop. Secure base
to the desktop by using clip plate (E4) and wingnut (N). Install the decorative cover
(H) to base finally.
Secure stand to the desktop by tightening clamp (E).
Install the decorative cover (H) to base finally.
B-3
A-3
B-1A-1
Mount base (C) to pole (B) using bolts (L). Tighten them by using 5mm allen key(J).
Mount Bracket (C) to base (C) using bolts (M). Tighten them by using 4mm Allen key(I).
Mount base (C) to pole (B) using bolts (L). Tighten them by using 5mm Allen key(J).
Mount carriage colt (O) to pole (B) using bolts (M).
DESK
DESK
Ф 10~60mm
Ф 0.39~2.36"
OPTION A: Clamp Installation
C-clamp
0.39~3.35" (10~85mm)
OPTION B: Grommet Base Installation
Φ0.39~2.36"
(Φ10~60mm)
Grommet
0.39~2.76" (10~70mm)
+90°
-90°
6.3"
160mm
7.6"-11"
192mm-280mm
2.1"
53mm
±135° ±180° ±90°
1.8"
45mm
MAX:
25"(635mm)
12.2"
310mm
4.3"
108mm
0.39~3.35"
(10~85mm)
0.39~2.76"
(10~70mm)
G (×1)
Cable Clip
E5
Bottom Plate
M (×4)
Bolt M6×10mm
O (×1)
Carriage Bolt M8×100mm
N (×1)
Wingnut M8
L (×3)
Bolt M6×20mm
H
H (×1)
Decorative Cover
I (×1)
4mm Allen Key
K (×1)
6mm Allen Key
J (×1)
5mm Allen Key
O
B
E4
N
H
J
E4
0.39~2.76"
(10~70mm)
0.39~3.35"
(10~85mm)
360°
75mm(2.95")
100mm(3.94")
112mm(4.4")
75mm(2.95")
100mm(3.94")
112mm(4.4")
14.3"
364mm
M-A (×5)
Screw M4×12mm
(one for spare)
M-B (×5)
Screw M4×30mm
(one for spare)
M-D (×4)
Spacer H13mm
M-C (×5)
Washer D4mm
(one for spare)
I
1.97~3.35"
(50~85mm)
E
MD
Attach the clamp (E) to the brace (D). Then tighten the bolts (M) with 4mm Allen key (I).
0.39~2.17"
(10~55mm)
I
E
M
D
M
D
I
C
E
C
LJ
B
C
LJ
B
E (×1)
Clamp
B (×1)
Pole
C (×1)
Base
A (×1)
Arm
D (×1)
Brace
A0
security bolt
M6×12mm
A1 (x1)
Cable Cover

4-2
4-1
Adjustments (If necessary)
4Cable Management 5
The gas spring is pre-set to minimum tension (4.4 lbs). For intended functioning of
the mount, you may need to adjust the tension of Arm in accordance with your
monitor weight by 6mm Allen key (K).
Tension Adjustment
1. Loosen the tilting bolt.
2. Adjust monitor to your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle.
Tilt Adjustment
Note:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.
Cable Clip (G)
Run cables through the cable
clip (G). Store Allen keys in
cable clip (G) for future use.
3
2-1 Select Correct Monitor Screw Length
Correct Correct Too LongToo Short
CAUTION: Too short will not hold your monitor. Too long will damage your monitor.
2-2
Attach VESA Plate to Monitor
2
Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the appropriate
screws and spacers for your monitor.
For more
spacing between
bracket and monitor
For protruded
back monitor
For counterbore
of monitor
To avoid the
blocked input
F
UP
Top of Monitor
Do not tighten the screws excessively or tighten them by
using the Electrodrill, or your monitor might be damaged.
J
MD
MA or MB
May be needed
MC
3-2
3-1
Install the cable clip (G) and arm (A) to the pole (B).
Fasten the bolts with 6mm Allen key (K).
Arm and Monitor Installation
3
Remove the pre-assembled security bolt (A0) from the upper arm (A).
Slide the monitor onto the head of upper arm (A), then install the security bolt (A0).
Make sure the security bolt (A0) is installed before you rotate the monitor.
A0
Tighten
A0 Remove
B
G
A
K
±135°
±90°
Height
Swivel
+90°
-90°
Tilt
Adjust monitor position and rotation.
±180°
Note: To ensure stability, the tightness of the
rotating axis has been preset, so it would be
kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first,
then hold the sides of it with both hands, and
rotate vigorously. If that doesn't work out,
please do not hesitate to ask for our help.
Rotate Vigorously
G
DESK
DESK
Please do not move stand
outside desk for safety!
360°
Rotation
Lower Arm
Remove the bottom plastic cover from lower arm
as shown in the diagram. Run cables through the
cable cover, then insert and slide the cover down
for reattachment.
Push and Slide (upward)
Insert and Slide (downward)
H
Tighten
Loosen
K
Option A: M4x12mm Option B: M4x30mm
27mm
9mm 14mm
Screw
VESA Plate
Spacer
Washer
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails
to stay where intended.
Solution:
Turn the inside screw counterclockwise
(“+”direction) to increase gas spring tension
until the arm can stay as intended.
Situation 2: Arm rises up or can't press down
Upper Arm with monitor rises up and fails to stay
where intended.
Solution:
Turn the inside screw clockwise (“-”direction) to
decrease gas spring tension until the arm can stay
as intended.
G
A1
Upper Arm
Run cables through the cable
cover(A1), then insert the cable
cover into the upper arm in the
direction shown and gently push
the cable cover down along the
upper arm so that the cable
cover is tightly fastened under
the upper arm.