Moustache MO-CD222P-8 User manual

CROSS CUT PAPER SHREDDER
MO-CD222P-8 Operation manual
Shred Type:
Shred Size:
Waste Container Capacity:
Standard Shredding Capacity:
Feed Opening:
Input:
Shredder Dimension:
Shredding Speed:
Continuous Working Time:
Cross Cut
5/32"×1-17/32"(4×39mm)
3.43 gallons(13L)
8 sheets of 80g/m²
220mm
110-120VAC,60Hz,2.5A
12.2"×6.5"×15"(310x164x380mm)
2.5m/min
2mins on/30 mins off
Specifications
For a minor paper jam
Both abnormal operations may result in the activation of the automatic thermal
motor overload protection circuit which terminates power to the shredder. A
paper jam could cause the thermal motor overload protection to terminate AC
power to the motor. Never allow the shredder to remain in a jammed condition
with the AC power turned on.
Place the slide switch in the REV position and pull the remaining sheets of paper
out of the feed opening. Remove the not shredded portion of paper from the top
and clean any excess paper shreds from the feed opening.
For a major paper jam
Turn off or unplug the power cord from the AC outlet and wait at least 30
minutes for the thermal overload protection to reset.
Plug in the AC power cord and place the slide switch in the AUTO position.
If paper was left inside the feed opening prior to the overload, place the
slide switch in the REV position, grasp the excess paper from the top, and
pull it out. Be careful to not place your fingers near the feed opening or
serious harm could result. Clear any excess paper shreds from the feed
opening. Place the slide switch in the AUTO position. You are now ready to
resume normal shredding.

Place the shredder securely on the top of the wastebasket. Be sure not to allow your
fingers to get between the basket and the shredder as you are placing the shredder
in pace.
When AUTO is selected. the shredding process is started automatically by inserting
the paper into the feed opening. The shredder will stop automatically when the
paper has completed its travel through the feed opening.
REV is used to assist in the removal of a paper jam, which reverses the shredding
process prior to a completed cycle, thus clearing the cutters.
OFF Position is recommended when emptying the wastebasket or when the shredder
is not in use for aprolonged period of time.
Plug the power cord into any standard 110~120VAC outlet.
The Switch is located on the top of the shredder. The Switch has three (3) settings.
This symbol is for the safety warning sign.
This symbol is for the user to read the instruction before use the machine
Sharp edges Do not touch.
Moving parts.
This means paper clips must not be inserted into cutting head.
Please keep children out of this shredder.
The sharp blade inside shredder may hurt children.
This means don't reach into the feed opening of the cutting head. This
could cause serious injury.
This means be careful of ties and other loose clothing or necklace which
could become entangled in the cutting head.
This means you should be careful if you have long hair which can
become entangled in the cutting head. This could cause serious injury.
keep off your necklace away from the feed opening.
Keep aerosol cans and small items away from the shredder.
MO-CD222P-8 will shred 8 sheets of 80g/m² A4 paper and will accept paper
width up to 8-2/3". When shredding small material like envelopes or credit
card receipts, insert them through the middle of the feed opening.
Setup:
Operating the shredder:
Shredder capacity:
Paper jams and overloads protection:
Cautions:
MO-CD222P-8 PAPER SHREDDER
1) Disconnect the power source prior to disabling or bypassing the equipment safeguard.
2) Restore the equipment safeguard before restoring power.
3) Unplug the equipment when not in use for an extended period of time.
4) AC plug is used to disconnect/ connect the equipment, the socket outlet should be easily accessible.
MO-CD222P-8 is equipped with a motor overload protection device, The normal
short duty cycle for continuous shredding at maximum capacity is 2 minutes on
and 30 minutes off. The power may terminate automatically in case of the
following abnormal situations:
Both abnormal operations may result in the activation of the automatic motor
overload protection, which terminates the power to the unit. If this occurs you
should:
Operating the shredder at the maximum capacity continuously for a
prolonged period of time, e.g. More than 2 minutes without stopping.
Exceeding the shredding capacity, e.g. Inserting more than 8 sheets of 80g/m²
A4 paper at one pass, or the paper is not feed squarely into the feed opening.
Unplug the power cord from the AC outlet and wait at least 30 minutes for the
overload protection to reset. Tear or cut off any excess paper from the top of
the shredder.
Plug the power cord back into the AC outlet and place the Switch in REV. Pull
the remaining paper out of the cutters. Place the Switch back to the Auto
position if necessary.
With the Switch in the AUTO position and the feed opening clear, you are now
ready to resume normal shredding. 20-Ib paper in one pass, or if the paper is
not feed squarely into the feed opening.