Movi M10 User manual
01. Loosen the 4 bolts holding the handle bar on to the
pan assembly of your MoVI M10.
(optional) Loctite screws and Install Toad in the Hole Male. 02. Mark motor to show front of unit with marker.
03. Lay unit on it’s side, cut and remove zip ties from
pan motor assembly.
04. Remove these screws, the carbon plate, and metal
plate underneath.
06. Loosen pan adjustment levers, or unscrew pan clamp
and remove pan assembly from unit and set aside.
07. Unscrew the GPS SMA connector. 08. Twist the GPS module o of the carbon plate and
clean any tape from GPS, set aside.
09. Loosen the 4 screws holding the vertical tube approx
2-5 turns until the tube is just loose enough to turn.
10. Remove the tube and set it aside.
05. Unplug the motor, careful not to pull from the wire
but the connector.
PART 1 : DISASSEMBLY AND PREPPING THE UNIT.
MōVI M10 Top Mount Upgrade
INSTALLATION INSTRUCTIONS
Thank you for your purchase of the new Top Mount Upgrade Kit for the MōVI M10. This
modication allows the M10 to operate without constraints in the SkyView top mounted
position on your ALTA, TERO, or any stable vertical mount like a tripod.
Please give yourself about an hour and a clear work space to work in. We recommend you
install our Toad in the Hole kit while performing this upgrade which will allow you to get
the most out of your Top Mount Upgrade.
Tools needed:
Wire cutter / diagonal side cutter.
1.5mm hex wrench, straight or ball tip.
2.0mm hex wrench, straight tip (not ball end.)
2.5mm hex wrench, straight or ball tip.
Needle nose plier, or similar (optional.)
Adhesive remover (optional.)
Toad in the Hole Kit (optional.)
11. Install your new keyed pan assembly as shown,
the levers should be pointing to the left of the unit.
12. Slide the tube in until it is just ush with the bottom
clamps and is not touching the motor.
14. Tighten the 4 screws evenly in a cross pattern until
they are tight.
13. From above, look down at the gimbal and twist the
keyed quick release until it is as square as possible with
the roll beam. (this can be adjusted later.)
15. Apply provided tape to your GPS unit and peel o
red backing.
16. Install your GPS back onto the plate as shown and
screw back on the SMA connector.
PART 3 : CONVERTING THE PAN ASSEMBLY.
16. Remove the 4 bolts from the motor and set the
carbon plate and bolts aside.
17. Remove the 4 button head bolts with a 2mm driver;
use caution and make sure the driver is fully seated to
avoid stripping.
18. Remove the 8 bolts with a 2.5mm driver, and the 5
button head bolts with a 2mm driver. Use pliers to hold
the posts if they spin.
19. Pull the carbon plates apart, save the motor and set
aside or discard the rest.
20. Unpack the parts shown. 21. Insert the 4 M3X37 screws provided through the
carbon plate with motor as shown, and lay at on your
work surface.
22. Place your metal tube with the open end inside the
plastic clamp as shown, place the matching part over
the top of the tube.
21. Using the carbon plate without threaded inserts,
install it to the motor as shown so the plug ts in the cut
out of the carbon and attach with your original socket
head bolts.
PART 2 : CONVERTING THE LOWER GIMBAL.
PART 3 : CONVERTING THE PAN ASSEMBLY (cont..)
23. Place the metal tube with plastic clamps over the
4 bolts as shown; making sure the keyed rib is on the
same side as the plugs on the motor.
24. Place the carbon with inserts over the motor, and
install the 4 button head screws into the motor. Make
sure the threaded inserts are facing out.
25. Reinstall the carbon plate to the motor, line up your
marks and reuse the original hardware with thread lock.
26. (optional) Install your Toad in the Hole Quick Release
with the lever facing towards the front.
27. Install battery cages with the M3X8 socket head
bolts - orient with the lever of the door facing up.
29. Slide the pan assembly on to the vertical tube - you
may need to loosen the clamp slightly to get it started.
Tighten these screws and adjust clamps to disired
snugness.
30. Plug both motor wires back in, being careful not
to force them as they are keyed to go in one way.
28. Ensure both cages are installed tight with the doors
facing up, and your pan tube is seated fully and the spine
is facing down.
31. Reinstall metal and carbon cover, use a zip tie to
securely tighten the wires to the carbon plate around
shrink tubing on wire.
33. Place a Freey M10 Aux Pack into the battery holder
and close. Plug in battery.
34. Attach top handle, and power on unit. Conrm it
will stablize and you’re done!
32. Place a second zip tie around the pan tube approx
a nger width back and secure the pan wire rmly along
the pan tube spine.
TROUBLE SHOOTING:
Should the M10 not power on and stablize check the following:
[LIGHTS DO NOT TURN ON] - Ensure battery is charged, plugged in, and the battery cables are undamaged.
[GIMBAL DOES NOT STABLIZE/FLASHING LIGHTS] - Double check the pan wiring, one of the plugs might not be
fully seated. Unplug the pan wires and plug them back in again, ensure the keyed portion of the plug is correct
and the plug is seated and not backwards.
[HANDLE BAR IS 90 DEGREES OFF] - Unmount the handle bar and turn 90 degrees, re-attach. If using a TITH you
may want to change the orientation of the receiver.
If you’re having diculty, please contact support@freeysystems.com for assistance.
Other Movi Drone & Quadcopter Accessories manuals
