MSA Evolution 6000 User manual

Operating Manual
Evolution 6000
Thermal Imaging Camera
Order No.: 10129292/09
Print Spec: 10000005389 (EO)
CR: 800000051847
MSAsafety.com

© MSA 2012, 2013, 2014, 2018, 2020, 2021, 2022. All rights reserved
WARNING!
Read this manual carefully before using or maintaining the device. The device will perform as designed only if it is used and
maintained in accordance with the manufacturer's instructions. Otherwise, it could fail to perform as designed, and persons
who rely on this device could sustain serious injury or death.
The warranties made by MSA with respect to the product are voided if the product is not installed and used in accordance with
the instructions in this manual. Please protect yourself and your employees by following the instructions.
Please read and observe the WARNINGS and CAUTIONS inside. For additional information relative to use or repair, call
1-800-MSA-2222 during regular working hours.
The Declaration of Conformity can be found under the following link: https://MSAsafety.com/DoC.
MSA is a registered trademark of MSA Technology, LLC in the US, Europe and other Countries. For all other trademarks visit
https://us.msasafety.com/Trademarks.
1000 Cranberry Woods Drive
Cranberry Township, PA 16066
USA
Phone 1-800-MSA-2222
For your local MSA contacts, please go to our website www.MSAsafety.com

Contents
1 Safety Regulations 4
1.1 Correct Use 4
1.2 Restrictions 4
1.3 Safety and Precautionary Measures 5
1.4 Laser Safety 6
2 Product Warranty 7
3 Description 9
3.1 Overview and Description of the Thermal Imaging Camera 9
4 Use 10
4.1 Safety Instructions 10
4.2 Switching ON and OFF 10
4.3 Securing the Camera During Use 10
4.4 NFPA 1801 Basic and Plus Mode Operation 11
4.5 User Interface and Operation (All Models) 11
4.6 EVOLUTION 6000+ TIC User Interface and Operation 15
4.7 Accessing the NFPA Plus Features 16
4.8 Accessing the Plus Features 17
4.9 EVOLUTION 6000X User Interface and Operation 19
4.10 Battery Installation 22
4.11 Battery Charging 22
4.12 Battery Care 24
5 Camera Setup 24
5.1 On-Screen Camera Setup (EVOLUTION 6000+ TIC and 6000X TIC Only) 24
5.2 Accessing On-screen Configuration Menu 25
5.3 Options 26
5.4 MSA EVOLUTION 6000 Configuration Application 30
6 Maintenance 32
6.1 Before Each Use 32
6.2 After Each Use 32
6.3 Germanium Lens Replacement 32
7 Service 33
8 Technical Data 34
9 Ordering Information 35
3 Evolution 6000 Thermal Imaging Camera
US

1 Safety Regulations
1.1 Correct Use
This manual includes detailed operating instructions for the complete EVOLUTION6000 Thermal Imaging Camera (TIC)
Series, including the EVOLUTION6000TIC, EVOLUTION6000+TIC and EVOLUTION6000XTIC, hereafter referred to as
camera. Each camera is designed to assist firefighters to see where visibility is impaired by smoke and darkness.
The cameras were designed to withstand the firefighting conditions of heat, flame, driving water spray, and frequent impact
normally seen by a firefighter. Extension beyond these demands may damage the camera and render it inoperable. It is not
recommended to use the camera for extended periods in high-heat conditions.
The thermal imaging camera is not a substitute for standard techniques and precautionary measures. The user must ensure
that the standard operational processes continue to be observed and maintained even when using the thermal imaging camera.
The thermal imaging camera can be used for the following purposes:
• Initial size-up/Scene assessment
• Locating the source of the fire
• Determining the extent of the fire
• Determining entry and ventilation points
• Detection of flashover dangers
• Search and rescue operations
• Hazmat situations
• Overhaul
• Preplanning/Fire code inspections
• Supporting police work
• Response vehicle navigation (darkness or heavy smoke)
1.2 Restrictions
The thermal imaging camera is not suitable for the following applications:
• Although the camera is waterproof, it is unable to take underwater images.
• Likewise, the camera does not image through glass, water or shiny surfaces which may act like a mirror.
• The camera does not improve the user's sight. Corrective lenses must continue to be worn.
It is imperative that this operating manual be read and observed when using the device. In particular, the safety instructions, as
well as the information for the use and operation of the device, must be carefully read and observed. Furthermore, the national
regulations applicable in the user's country must be taken into account for a safe use.
Alternative use, or use outside this specification will be considered as non-compliance. This also applies especially to
unauthorised alterations to the product and to commissioning work that has not been carried out by MSA or authorised
persons.
The warranties made by MSA with respect to the product are voided if the product is not used and serviced in accordance with
the instructions in this manual. Please protect yourself and others by following them. We encourage our customers to write or
call regarding this equipment prior to use or for any additional information relative to use or repairs. During regular working
hours, call 1-877-MSA-FIRE in the US.
Evolution 6000 Thermal Imaging Camera 4
1 Safety Regulations US

This camera contains batteries and electronics. Dispose of or recycle in accordance with all applicable federal state and local
regulations.
By order of the US Department of Commerce, in conjunction with the US Department of State and DOD, this Thermal Imaging
Camera may not be resold, re-exported, transferred, or otherwise disposed of outside of the country named as the location of
foreign end use, either in its original form or after being incorporated into other end items, without the prior written approval of
the US Department of Commerce. Violation of this regulation may result in fine and/or imprisonment.
1.3 Safety and Precautionary Measures
WARNING!
• The user must be trained and thoroughly familiar with proper operation and limitations of the thermal imaging camera
prior to use. Use in controlled live-burn exercises is suggested before using the equipment in actual emergency
situations.
• Do not rely on the thermal imaging camera as the sole means of navigation or deviate from standard fire-fighting
navigational practices during use. Although the system provides an image in dark and smoky environments, the user
may become disoriented or lost in such environments if the system becomes inoperative.
• Most electronic devices cease to operate at certain high temperature extremes. Tests on the EVOLUTION6000 Series
TICs indicate that they provide an acceptable image when subjected to an ambient temperature of approximately 120°C
(248°F) for 20 minutes. Exposure to conditions exceeding these result in deterioration and loss of image.
• This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, ClassII, Division2, Groups F and G or
nonhazardous locations only (equivalent to ATEX industrial area, equipment group II, zone 2, gas group IIB).
• This thermal imaging camera is not rated as "Intrinsically Safe". Do not use the system in environments or atmospheres
where static or sparks may cause an explosion.
• Before entering a hostile environment, test the thermal imaging camera as specified in the instructions to ensure that it is
functional. After each use, inspect the camera to determine if servicing is required.
• Exposure to high temperature environments for an extended period of time may cause degradation or loss of thermal
image. Avoid heat saturation or overexposure of the equipment. If degradation of the thermal image is observed,
immediately remove the equipment from the high heat environment and allow it to cool until the thermal image returns to
normal; otherwise, the system may become inoperative.
• Do not mark the camera i.e., with stamps, labels, paint or other method. Use of such markings may interfere with
camera use or may constitute a flammability hazard.
• Replacement batteries must exactly match the ratings and configuration of those supplied with the camera. Use of
unapproved batteries may render the system inoperative.
• Use only battery chargers made available by MSA for use with this device; other chargers may damage the battery pack
and the device. Dispose of batteries in accordance with local health and safety regulations.
• Do not remove the thermal imaging camera cover or casing. Only authorized personnel may service the camera.
• Ensure battery is fully charged before use. If not fully charged, the camera will not operate for the specified amount of
time. Monitor battery level during use and immediately exit the hazardous area when a low battery warning is observed.
• Electromagnetic radiation (radio transmissions) may cause interference. Minimize nearby radio transmissions if
excessive interference occurs.
• Do not point the thermal imaging camera directly at the sun; otherwise, damage to the detector may occur.
• Do not drop the thermal imaging camera. Although the camera is designed to withstand normal impacts that occur in fire
service, such impacts may alter the focus or damage the unit.
Failure to follow these warnings can result in serious personal injury or death.
5 Evolution 6000 Thermal Imaging Camera
US 1 Safety Regulations

CAUTION!
To avoid lens fogging, the user may coat the lens and display window with MSA anti-fog material (MSA P/N 13016).
Failure to follow this caution can result in minor or moderate injury.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency and, if not installed in accordance with
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canada:
This Class B digital apparatus complies with Canadian ICES-003.
1.4 Laser Safety
The EVOLUTION6000 series of thermal imaging cameras utilizes lasers in both the laserpointer/flashlight and the laser range
finder optional modules. Figure 1indicates the locations of the lasers within the camera.
Figure 1 Laser locations
1 Pointer Laser (Red) 2 Range Finder Laser (IR)
Laser Max.
Power
Wavelength Beam Divergence Pulse Duration
Pointer (Red) 5 mW 650 nm 0.70 mRAD Continuous
Range finder (IR) 1.6 µJ905 nm 5.37 mRAD 25 nS
Evolution 6000 Thermal Imaging Camera 6
1 Safety Regulations US

Figure 2 TIC label
1.4.1 Removal from Service
A decision to retire the Thermal Imaging Camera should be based on inspection data, and whether that data meets the
specified level of performance as defined in maintenance requirements from MSA.
2 Product Warranty
Express Warranty
MSA warrants that this product and its accessories are free from mechanical defects or faulty workmanship as prescribed in
the chart below, provided they have been installed, used, and maintained in accordance with the instructions and/or
recommendations contained in the instructions delivered with the equipment. MSA shall be released from all obligations under
this warranty in the event repairs or modifications are made by persons other than its own or authorized service personnel. No
agent, employee or representative of MSA has any authority to bind MSA to any affirmation, representation or warranty
concerning the goods sold, and unless an affirmation, representation or warranty made by an agent, employee or
representative is specifically included within the written agreement for the goods sold it shall not be enforceable by the original
end-user. MSA makes no warranty concerning components or accessories not manufactured by MSA, but will pass on to the
original end-user all warranties of manufacturers of such components. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, AND IS STRICTLY LIMITED TO THE TERMS HEREOF. MSA
SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR
PURPOSE.
Products covered by this Express Warranty include the EVOLUTION6000, EVOLUTION6000+ and EVOLUTION6000X
Thermal Imaging Cameras (TICs). All warranty periods referenced below are from the date of sale to the original end-user
unless otherwise noted.
Thermal Imaging Camera (includes camera core and
camera components)
2 years
Truck/Wall/Desktop Chargers, ExternalReceivers
and Transmission Equipment
1 year
Replacement Parts / Repairs (non-warranty) 90 Days from date of repair
Factory Upgrades 90 Days or remainder of existing
warranty, whichever is longer
Extended Service
MSA offers an Extended Service contract for TICs at the customer's request. Details are listed on the next page of this
manual.
Contact MSA Fire Service Customer Service (1-800-MSA-2222 in the US) for additional information and arrangements.
For information on availability outside the US, contact your local MSA representative.
7 Evolution 6000 Thermal Imaging Camera
US 2 Product Warranty

Loaner Cameras
MSA offers a loaner camera program for customers when deemed necessary (extended repair time, critical equipment
replacement, etc.). The loaner camera will not necessarily be the exact model that it is replacing. Contact MSA Fire Service
Customer Service (1-800-MSA-2222 in the US) for additional information and arrangements.
Exclusive Remedy
It is expressly agreed that the original end-user's sole and exclusive remedy for breach of the above warranty, for any tortious
conduct of MSA, or for any other cause of action, shall be the repair and/or replacement, at MSA's option, of any equipment or
parts thereof, that after examination by MSA are proven to be defective. Replacement equipment and/or parts will be provided
at no cost to the original end user, F.O.B. original end-user's named place of destination. Failure of MSA to successfully repair
any nonconforming product shall not cause the remedy established hereby to fail of its essential purpose.
Exclusion of Consequential Damage
Original end-user specifically understands and agrees that under no circumstances will MSA be liable to original end-user for
economic, special, incidental, or consequential damages or losses of any kind whatsoever, including but not limited to, loss of
anticipated profits and any other loss caused by reason of the non-operation of the goods. This exclusion is applicable to
claims for breach of warranty, tortious conduct or any other cause of action against MSA.
Product Registration and Extended Warranties for MSA TICs
Thank you for purchasing an MSA Thermal Imaging Camera. Registering your products with MSA will improve the processing
of any warranty claims and enable you to receive information regarding product updates and new products. Please register
your camera online or purchase an extended warranty at www.MSASafety.com/register.
MSA requires that the camera and accessories be installed, used, and/or maintained as specified in the product instructions.
All TICs and accessories sent in for warranty repair will be inspected for signs of excessive rough handling and operation
significantly beyond specifications in the instructions. The warranty coverage is for material defects and/or faulty
workmanship only. Repair and labor required for normal wear and tear are not covered under the warranty and are the
responsibility of the original end-user.
For information on availability outside the US, contact your local MSA representative.
EVOLUTION Thermal Imaging Camera Extended Warranty
Extended warranties must be processed for EACH Thermal Imaging Camera.
Apply for your MSA Thermal Imaging Camera Extended Warranty coverage online at www.MSASafety.com/register or
phone (1-800-MSA-2222 in the US, other countries: contact information on the last page of this manual) for assistance.
• Extended warranty requests MUST be exercised within the first 6 months from the date of -manufacture. The last three
characters (MYY, or "month-year-year") of the TIC's serial number (located in the battery compartment of the Thermal
Imaging Camera) dictate this timeframe (XX-XXXX-MYY).
• Extended warranty coverage is available up to 36 months after the standard warranty has expired. Select the Extended
Warranty coverage for one, two or three years.
• Extended warranty rates are: one year = $1,000.00, two years = $2,250.00 and three years = $3,750.00.
• Extended warranty and standard warranty both begin from the date of purchase by the end user.
• This Extended Warranty program applies only to MSA Thermal Imaging Cameras. Consumable batteries, battery
chargers and accessories are not covered.
Evolution 6000 Thermal Imaging Camera 8
2 Product Warranty US

NOTE: This manual contains only a general description of the products shown. While uses and performance capabilities are
described, under no circumstances shall the products be used by untrained or unqualified individuals and not until the product
instructions including any warnings or cautions provided have been thoroughly read and understood. Only these instructions
contain the complete and detailed information concerning proper use and care of these products.
For information on availability outside the US, contact your local MSA representative.
3 Description
3.1 Overview and Description of the Thermal Imaging Camera
Figure 3 The EVOLUTION 6000 camera
All EVOLUTION 6000 Series Thermal Imaging Cameras are:
• equipped with a 320 x 240 uncooled microbolometer heat sensor which provides clear, highresolution images
• equipped with a large screen, high definition display
• equipped with a built-in flashlight and laser pointer
• dustproof and waterproof for short periods submerged under water up to a depth of 3 feet (1m) corresponding to IP 67
• able to be configured through a desktop PC through our FireService Utility software
• available with multiple carrying and attachment options
In addition to the above features, the EVOLUTION 6000+ TIC:
• features a 2X/4X digital zoom feature
• is equipped with up to five user-selectable palettes in addition to standard "white-hot" imagery
• includes a solid state compass to aid in navigation
• offers an optional laser range finder to accurately measure distances (replaces flashlight and laserpointer if selected)
• able to be configured on the camera or through a desktop PC using MSA's FireService Utility software
Our most advanced camera, the EVOLUTION 6000X TIC, offers all of the above and also includes:
• a fully integrated video recording system with USB download capability
• the ability to snap, store and download still pictures through the integrated USB connection
9 Evolution 6000 Thermal Imaging Camera
US 3 Description

4 Use
4.1 Safety Instructions
Check the batteries before and during use
Check whether the batteries are fully charged before using. If not fully charged, the nominal operating time cannot be achieved.
Also check the battery level during use.
For details on charging →4.11 Battery Charging.
4.2 Switching ON and OFF
Switching ON in normal mode, function test
Figure 4 ON/OFF button
1. Press green ON/OFF button for approximately 1 second.
a. Within 5 seconds, the TIC carries out a self-test of the sensor electronics.
Status LEDs under display illuminate according to battery status ( → 4.5.8 Battery Status Indicator).
The current software version briefly displays.
An image appears after a few seconds on the display.
2. Check camera function:
a. Direct the camera toward an object or person until the thermal image shows on the display.
The camera is now ready for use.
Switching OFF
1. Keep ON/OFF button pressed for approximately 3 seconds until all LED indicators switch off.
2. Release the ON/OFF button as soon as all LED indicators switch off.
The camera is switched OFF.
4.3 Securing the Camera During Use
The camera may be secured to the user in different ways using one of the self-retracting attachment cables.
Evolution 6000 Thermal Imaging Camera 10
4 Use US

Figure 5 Attachment cable locations
To use the attachment cables:
1. Pull the spring loaded cable out and away from the camera body.
2. Slip a carabiner or similar securing device through the cable loop.
3. Release the cable.
Internal springs automatically pull the attachment cables in tight to the camera housing to minimize any snag hazards.
4.4 NFPA 1801 Basic and Plus Mode Operation
Certain Evolution 6000 camera models are compliant with NFPA 1801 Standard on Thermal Imagers for the Fire Service; 2021
Edition. See approval information on the label located on the underside of the camera housing. NFPA1801 describes a
required "Basic Mode" of operation common among all compliant thermal imaging cameras. It also allows for a "Plus Mode"
operation which, once accessed, provides a number of useful features and options for the firefighter trained in their use.
The EVOLUTION6000 camera always operates in the NFPA 1801 defined "Basic Mode". The EVOLUTION6000+ and
EVOLUTION6000X TICs, however, provide "Plus Mode" features. For more information, see 4.7 Accessing the NFPA Plus
Features
Non-NFPA compliant EVOLUTION6000+ and EVOLUTION6000X TICs do not have a "BasicMode" and will automatically
operate in "Plus Mode" when the camera is turned on.
4.5 User Interface and Operation (All Models)
The following features and functions are common to all camera models. Additional User interface and Operating instructions
for the EVOLUTION6000+ TIC can be found in this chapter, and, for the EVOLUTION6000X TIC, in 4.9 EVOLUTION 6000X
User Interface and Operation.
Many features can be custom configured using the MSA Fire Service Utility.
The EVOLUTION6000+ TIC and EVOLUTION6000X TIC also include an on-screen configuration feature that allows basic
setup modifications to be made without a computer. For more information, see 5 Camera Setup.
11 Evolution 6000 Thermal Imaging Camera
US 4 Use

4.5.1 On-Screen Indicators (All Models)
Figure 6 On-Screen indicators
1 Shutter indicator 4 Color reference bar
2 Low sensitivity mode indicator 5Digital temperature target
3 Internal over temperature indicator 6 Record icon
4.5.2 High and Low Sensitivity Mode
The camera has a high and a low sensitivity mode for showing images in different temperature ranges.
• After turning the camera ON it will be in the high sensitivity mode.
• The camera automatically switches from high sensitivity mode to low sensitivity mode in case of extreme heat (a
significant portion, 32% of pixels) of the image exceeding 140°C.
In this case, the display shows a small green triangle above the color reference bar to indicate that the scale changed from
the high sensitivity mode scale. A larger green triangle appears in the upper left-hand corner of the display.
• The camera switches from low sensitivity mode to high sensitivity mode when 89% of pixels show less than 120°C.
In the low sensitivity mode, the camera's dynamic range expands to enable the user to distinguish objects and people more
easily in environments with large temperature ranges. This mode also prevents white-out. (White-out or over-saturation occurs
when a thermal imaging detector is subjected to too much thermal energy, and the image, which appears as a white cloud, no
longer identifies fine details in the scene.)
4.5.3 Shutter Indicator
When the camera is in operation, it is periodically necessary to refresh the focal plane array in order to operate properly. This
occurs via an internal shutter mechanism. When the camera shutters, the camera image freezes for approximately one
second.
The shutter indicator is a green square shown at the top left of the display for approximately 3 seconds before and during the
shuttering cycle (Pos.1, Figure 6 ).
Shuttering may occur more frequently with greater heat load.
Evolution 6000 Thermal Imaging Camera 12
4 Use US

4.5.4 Color Reference Bar
The Color Reference Bar spans temperatures from 0°F (0°C) to 300°F (160°C) in High Sensitivity mode and 0°F (0°C) to
1000°F (600°C) in Low Sensitivity mode and provides a temperature reference for the Temperature Indicator Bar. The scale
dynamically changes with a change in sensitivity mode. A green triangle appears over the scale to indicate a sensitivity mode
other than high-sensitivity mode.
• The scale is also used as a reference for image colorization. The yellow, orange and red segments of the bar correspond
to the temperatures at which colorization is introduced on the camera.
NOTE: Colorization is introduced at different temperatures depending on High or Low Sensitivity mode.
The Color Reference Bar is only visible for "White Hot" imagery.
4.5.5 In High Sensitivity Mode
When Temperatures are Objects:
below 291°F (144°C) Are shown as standard gray scale images
between 291°F (144°C) and 302°F (150°C) Turn yellow, starting with light shades changing to darker shades
between 302°F (150°C) and 311°F (155°C) Turn orange, starting with light shades changing to darker shades
over 311°F (155°C) Turn red, starting with light shades changing to darker shades
4.5.6 In Low Sensitivity Mode
When Temperatures are: Objects:
between 1000°F (540°C) and 1047°F (564°C) Turn yellow, starting with light shades changing to darker shades
between 1047°F (564°C) and 1090°F (588°C) Turn orange, starting with light shades changing to darker shades
over 1090°F (588°C) Turn red, starting with light shades changing to darker shades
4.5.7 Over Temperature Warning
An Over Temperature Warning activates when the internal system electronics approach maximum recommended operating
temperature limits.
• A red indicator flashes on the center top section of the display area when the camera exceeds recommended operational
thermal limits.
WARNING!
Most electronic devices cease to operate at certain high temperature extremes. Tests on the EVOLUTION6000 series of
TICs indicate that they provide an acceptable image when subjected to an ambient temperature of approximately 120°C
(248°F) for about twenty minutes. Exposure to conditions exceeding these may result in deterioration and loss of image.
Failure to follow this warning can result in serious personal injury or death.
The environmental thermal tolerance values for the camera can be found in 8 Technical Data.
13 Evolution 6000 Thermal Imaging Camera
US 4 Use

4.5.8 Battery Status Indicator
Figure 7 On-Screen indicators
1 Battery charging indicator 3 Display brightness sensor
2 Battery status indicator
Remaining battery capacity is shown by 4 equal battery segments:
Indication Remaining Battery Capacity
4 green segments Nominal 75 to 100%
3 green segments Nominal 50 to 75%
2 yellow segments Nominal 25 to 50%
1 red segment Nominal 0 to 25%
1 red segment flashing Critically low battery (5 minutes or less remaining)
NOTE: If the red segment flashes three times at turn-ON, the battery is too low to operate the camera and the camera will
switch OFF.
4.5.9 Battery Charging Indicator
When the camera is placed into the optional vehicle charger, the charging indicator shows the charging status.
• Red indicates charging is in progress.
• Green indicates charging is complete.
NOTE: If the indicator is not lit, the camera is not in proper contact with the vehicle charger base. Ensure that camera is
properly installed in the charger and that charger has power. Clean the battery charging contacts on the front of the camera if
necessary.
4.5.10 Trigger Button
Figure 8 Trigger button
Evolution 6000 Thermal Imaging Camera 14
4 Use US

Flashlight and Laser Pointer
WARNING!
Safety measures which must be observed:
Observe the appropriate country-specific safety measures for users of laser class 3R equipment.
Laser class 3R laser equipment is potentially hazardous to eyes. Use of operating and adjustment equipment and procedures
other than those indicated here can lead to dangerous exposure to radiation. Modification of the laser equipment is not
permitted. This Operating Manual must be retained and passed to the next owner of the laser equipment.
Personal safety precautions:
This laser equipment may only be used by properly trained persons. Do not aim the laser beam at people. If the laser beam
falls directly on your eye, consciously close your eyes and move your head out of the beam immediately. Do not look into the
direct or reflected beam. Do not aim the laser beam at people. Persons under 18 years of age must not use this equipment.
Safety measures to be applied in areas where the equipment is used:
Ensure that no-one can look directly into the laser beam:
• Avoid accidental reflections, for example by covering or removing reflective surfaces in the vicinity of the laser
equipment
• Position / align the laser beam well away from eye height
• Restrict the laser beam to the area where it is to be used, for example by screening with non-reflective surfaces
• When not in use, store the laser equipment so that it cannot be accessed by unauthorised persons
Failure to follow this warning can result in serious personal injury or death.
The built-in flashlight and laser pointer is standard equipment in the camera.
The flashlight is an LED-based light that can be used to aid navigation in darkness and light smoke.
The laser pointer tool allows the camera operator to highlight an object or area requiring attention.
NOTE: The laser pointer and flashlight will not function at the same time.
NOTE: Should the laser beam appear to be weak or distorted, ensure that the laser pointer window on the front of the camera
is free of dirt and water.
Trigger Button Operation Result
First short press Turns ON the flashlight
Second short press Turns OFF the flashlight and turns ON the laser pointer
Third short press Turns OFF the laser pointer
The trigger button also activates the distance meter/range finder ( →See 0.0.1 Range Finder Plus Feature) if the camera is
so equipped.
4.6 EVOLUTION 6000+ TIC User Interface and Operation
The following features and functions are common to the EVOLUTION6000+ TIC and EVOLUTION6000X TIC models.
Additional user interface and operating instructions for the EVOLUTION6000X TIC can be found in4.9 EVOLUTION 6000X
User Interface and Operation
15 Evolution 6000 Thermal Imaging Camera
US 4 Use

Figure 9 Additional buttons EVOLUTION6000+ TIC and 6000 X TIC
1 ZOOM button 2 PALETTE button
Figure 10 Additional EVOLUTION6000+ TIC and 6000 X TIC on-screen indicators
1 Plus Mode indicator 4 Color Palette indicator (Plus Feature)
2 Zoom Level indicator (Plus Feature) 5 Range Finder
3 Compass (Plus Feature) 6 Record icon
7 Temperature Indicator (Plus Feature)
4.7 Accessing the NFPA Plus Features
Thermal imaging cameras compliant with NFPA 1801, Standard for Thermal Imaging Cameras in the Fire Service, require a
deliberate action to access all camera features beyond those described as NFPA Basic functions.
Non-NFPA-compliant cameras (reference the approval label on the underside of the camera) do not require a special
sequence. All features are available at camera turn-ON.
Evolution 6000 Thermal Imaging Camera 16
4 Use US

WARNING!
Do not attempt to use NFPA Plus features without adequate training. Without proper training, some features may lead to
firefighter disorientation and unexpected camera operation.
Failure to follow this warning can result in serious personal injury or death.
Once the camera is turned ON, push and hold either the ZOOM or the PALETTE button for three seconds until the Plus Mode
Indicator appears on the screen (→"EVOLUTION 6000X User Interface and Operation" ).
• All Plus features are now available.
• All applicable indicators appear on screen.
To return to the Basic mode:
1. Briefly push and release the ON/OFF button, or
2. Turn the camera OFF and back ON again.
The Plus mode indicator and any applicable feature indicators turn OFF.
4.8 Accessing the Plus Features
4.8.1 Digital Temperature Target/Digital Temperature Indicator
The Digital Temperature Indicator provides an approximate numeric temperature of an object in Fahrenheit or Celsius,
depending on the camera settings. To measure the temperature of an object, aim the camera so the digital temperature target
(Pos. 5, 4.8 ) in the center of the display is on the object to be measured.
NOTE: Displayed temperature is an average of pixels within the green box. An incorrect temperature could display if all pixels
are not on the object to be measured.
NOTE: The digital temperature indicator is only available in Plus Mode.
Temperature range is:
• -40°F (-40°C) to 1022°F (550°C) in Low Sensitivity mode and
• -40°F (-40°C) to 320°F (160°C) in High Sensitivity mode.
Displayed temperature is intended to provide the user with an approximate temperature reading. For the digital temperature
accuracy indicator, see 8 Technical Data.
4.8.2 Digital Zoom Select (Plus Feature)
Digital zoom narrows the apparent angle of view of the image, it takes a portion of the image and expands that image to the full
size of the screen.
The camera enters the Plus mode in standard 1X zoom.
1. Push the ZOOM button once for a 2X zoom.
The Zoom Indicator shows 2X.
2. Push the ZOOM button again for a 4X zoom.
The Zoom Indicator shows 4X.
3. Push the ZOOM button again to return to standard 1X zoom.
17 Evolution 6000 Thermal Imaging Camera
US 4 Use

The Zoom indicator turns OFF.
4. Push and hold the ZOOM button for two seconds to skip immediately back to 1X zoom.
4.8.3 Color Palette Select (Plus Feature)
The camera enters the Plus mode with standard white-hot imagery. The EVOLUTION6000+ TIC and EVOLUTION6000X
TIC feature up to five user-selectable display palettes to enhance imagery in a variety of operational environments. The Color
Palette selection (PALETTE) button steps the camera through the available color palettes. In addition to standard white-hot,
five additional color palettes are available.
1. Push the PALETTE button to access the available color palettes.
The Color Palette indicator displays a label for the selected palette.
Each push of the PALETTE button steps the camera to the next available palette.
NOTE: The color palette loops back to standard white-hot after the last available color palette.
2. Push and hold the PALETTE button for two seconds to skip immediately back to the standard white-hot palette.
4.8.4 Color Palette Indicator (Plus Feature)
The selected color palette, for example white hot, displays in this box ( →4.5 User Interface and Operation (All Models). For
information on disabling color palettes, choosing alternate color palettes and selecting the number of available color palettes,
→5 Camera Setup.
4.8.5 Compass (Plus Feature)
Compass (Plus Feature)
The integral compass feature allows the user to determine the direction the camera is pointed in 45° increments (N, NE, E, SE,
S, SW, W and NW). Compass direction may be displayed using text or graphics. Reference compass settings in the camera
configuration software (see4.3 Securing the Camera During Use).
• The compass must be calibrated before use. For instructions, see 5.3.2 Configuring Options.
• The camera must be held within 45° of vertical for compass to obtain an accurate reading. If the camera is tilted too far in
any direction, "==" displays instead of the direction.
Evolution 6000 Thermal Imaging Camera 18
4 Use US

Figure 11 Camera orientation
True north displays if true north is selected and a valid declination angle is entered during setup. The default is magnetic north.
For text display mode, if magnetic North is selected, orientation is shown as green letters on black background. If True North is
selected, yellow letters on black background show the compass orientation. For icon display mode, magnetic North has a
green flag next to the icon. True North has a yellow star next to the icon.
As with any compass, soft iron and localized magnetic fields may result in incorrect compass readings. It is recommended
that the compass be calibrated every month or immediately after being subjected to a strong magnetic field. Examples of
strong magnetic fields include, but are not limited to:
• power lines
• transformers
• strong magnets.
A compass indicator of "CC" indicates that compass is out of calibration. For instructions, refer to 5.3.2 Configuring Options
WARNING!
As with any magnetic compass, the indicated direction can be influenced by soft iron structures, including buildings and
localized magnetic fields from nearby electrical equipment. Do not rely on the compass as a sole means of navigation. The
compass is intended to be an aid and is not a substitute for proper training.
Failure to follow this warning can result in serious personal injury or death.
For information on enabling and disabling the compass, selecting either a text or an icon indicator, compass calibration, and
entering a local declination angle for true north readings, see 5.3.2 Configuring Options
4.9 EVOLUTION 6000X User Interface and Operation
In addition to the features, functions and options found in the EVOLUTION6000 and EVOLUTION6000+ models, the
EVOLUTION6000X camera features image and video capture capability.
4.9.1 On-Screen Indicators
Figure 12 On-screen indicators
1 Date and time 3 Record icon
2 Image capture
19 Evolution 6000 Thermal Imaging Camera
US 4 Use

4.9.2 Video Capture
Video capture is available in both the NFPA Basic and NFPA Plus operational modes as it does not impact camera operation.
When video capture is enabled and turned ON (in camera configuration or via the MSA FireService Utility application), the
EVOLUTION6000X TIC begins recording video in five-minute MPG4 formatted video clips. A time and date stamp on the
display indicates the start of each new five minute clip.
NOTE: The time and date stamp does not appear on the display or captured video when the EVOLUTION6000X TIC is in
NFPA Basic mode. However, video is still captured if video capture is enabled.
NOTE: The video capture system requires approximately 30seconds to start up before video is captured. Although an image
will apear on the screen, no video will be captured during this time.
4.9.3 Image Capture
NOTE: Image capture is only available in the NFPA Plus operating mode. Activation of image capture differs, depending on
installation of the flashlight/laser pointer option or the range finder option.
Still images can be captured using the Trigger button and saved to EVOLUTION6000X TIC memory for later download to a
PC.
4.9.4 Trigger Operation with Flashlight and Laser Pointer Option Installed
Successive Trigger Pulls Result
First short pull Turns flashlight ON
Second short pull Turns flashlight OFF and turns laser pointer ON
Third short pull Turns laser pointer OFF
Single, long trigger pull Captures a still image
NOTE: The laser pointer and flashlight do not function at the same time.
4.9.5 Trigger Operation with Range Finder Option Installed
Trigger Pulls Result
Short trigger pull Captures a still image
Long trigger pull Takes a distance measurement
4.9.6 Naming Conventions for Still Image Files and Video Files
Still images are stored as JPG files in a directory called "Pictures" and named by date and time in modified ISO 8601
formatting.
For example 2012_05_14-13-58-00.jpg is a still image captured at 13:58:00 (1:58PM) on May14th, 2012.
Video files are stored as MPEG 4 files in a directory called "Video" and also named by date and time.
For example: 2012_02_14-18-23-45.M4V is a video file started at 18:23:45 (6:23:45PM) on February14th, 2012.
VLC Video Player from VideoLAN (free download: www.videolan.org) is recommended for opening and viewing video files.
Evolution 6000 Thermal Imaging Camera 20
4 Use US