MSI MS-1358 User manual

S30 (MS-1358) Disassemble Guide
■1、BATTERY
■2、KEYBOARD
■3、UPPER CASE
■4、HDD MODULE
■5、LOWER CASE
■6、WLAN MODULE
■7、MOTHER BOARD AND TOUCHPAD MODULE
■8、LCD MODULE

S30（MS-1358）Disassemble Guide
1、BATTERY
1.1：Move the “Unlock’ button base on left picture
shows.
1.2：Release the “Release” button and move the
battery pack base on left picture.
Component
P/N
Qty
Battery Pack
S9N-2141400-SB3
1
1.3：Remove the 6 screws (M2*3mm).
Attention: the screw driver touque is: 1.5-2.0Kgf-cm
Component
P/N
Qty
Screw
E43-1203003-H29
6

S30（MS-1358）Disassemble Guide
2、KEYBOARD
2.1：Remove the Keyboard.
2.2：Firstlypush the handspike on two sides
of the K/B cable connector according to the
direction as pic shows; then remove the
cable.
Component
P/N
Qty
Keyboard
S1N-2EUS341-SA0
1

S30（MS-1358）Disassemble Guide
3、UPPER CASE
3.1：Remove the 7 screws (M2*3mm) and 1 screw
(M2*6mm)..
Attention: the screw driver torque is: 1.0-1.5Kgf-cm
Attention: the screw driver torque is: 1.5-1.8Kgf-cm
Component
P/N
Qty
Screw
E43-1206001-H29
1
Screw
E43-1203003-H29
7
3.2：Disconnect Touchpad Cable.

S30（MS-1358）Disassemble Guide
3.3：When remove the Upper case, first
remove the two sides, then remove the down
side, last detach the Upper case down side
from Lower case.
Attention: Don’t use the heavy strength to
pull the Upper case; and the Touchpad cable
is connected with the main board.
Component
P/N
Qty
Upper Case
307-358C111-TA2
1
3.4：Remove the 7 screws (M2*3mm) and 2
screws (M2*5mm).then remove the Upper
Case Frame.
Attention: the screw driver torque is: 1.0-1.5Kgf-cm
Attention: the screw driver torque is: 1.5-1.8Kgf-cm
Component
P/N
Qty
Upper Case Frame
307-358E111-TA2
1
Screw
E43-1203009-H29
7
Screw
E43-1206701-H29
2

S30（MS-1358）Disassemble Guide
4、HDD MODULE
4.1：Remove the HDD Module according to the
direction as pic shows;
Component
P/N
Qty
HDD Module
S71-2450547-W36
1
4.2：Remove the DRAM Module according to
the direction as pic shows;
Component
/N
Qty
DRAM Module
S7C-S45AH02-E54
1

S30（MS-1358）Disassemble Guide
5、LOWER CASE
5.1：Remove the 3 screw(M2*3mm)
Attention: the screw driver torque: 1.0-1.5Kgf-cm
Component
P/N
Qty
Heatsink
E31-0802443-Y31
1
Screw
E43-1203003-H29
3
5.2：Remove the 2 screw(M2*3.5mm)
Attention: the screw driver torque: 1.0-1.5Kgf-cm
.
Component
P/N
Qty
Screw
E43-1203501-H29
2
5.3：Remove the I/O Board
.
Component
P/N
Qty
I/O Board
607-1358B-01S
1
2
1
3

S30（MS-1358）Disassemble Guide
5.4：Remove LVDS Cable.
.
Component
P/N
Qty
LVDS Cable
K19-3023005-V03
1
5.5：Remove Power Cable.
.
5.6 ：Remove Camera Cable and Speaker
Cable.
.

S30（MS-1358）Disassemble Guide
6、WLAN MODULE
6.1：Remove the 2 screw(M2*3.5mm)
Attention: the screw driver torque: 1.0-1.5Kgf-cm
Component
P/N
Qty
Screw
E43-1203501-H29
2
6.2：Remove the Wlan board as left pic shows,
then remove the two side wireless card antenna as
pic shows.
6.3：Remove 2 screw (M2*3.5mm), then
remove the WLAN module according to the
direction of pic shows.
Attention: the screw driver torque is: 1.5-1.8Kgf-cm
Component
P/N
Qty
WLAN Card
S78-4404300-S77
1
Screw
E43-1203501-H29
2

S30（MS-1358）Disassemble Guide
6.4 ：Remove the 2 screw(M2*3.5mm), then
remove the Power Board
Attention: the screw driver torque is 1.0-1.5Kgf-cm
Component
P/N
Qty
Power Board
607-1358A-01S
1
Screw
E43-1203501-H29
2
6.5：Remove the 3 screw (M2*3.5mm),
Attention: the screw driver torque is 1.0-1.5Kgf-cm
Component
P/N
Qty
Screw
E43-1203501-H29
3
6.6：Disconnect Fan Cable,then remove the FAN..
Component
P/N
Qty
FAN
E33-0800270-MC2
1