MSI MS-1651 - Whitebook ID2 - 15.4 User manual

GX620 （MS-1651）Disassemble SOP
■ 1、Battery Pack
■ 2、BOTTOM DOOR ASSY
■3、THERMAL-KIT And CPU Module
■ 4、RAM、WLAN And TUNER Module
■ 5、HDD Module ASSY
■ 6、ODD Module ASSY
■ 7、HINGE COVER ASSY
■ 8、UP CASE ASSY
■ 9、LOWER CASE ASSY
■10、LCD MODULE ASSY

GX620&MS-1651 Disassemble SOP
■ 1、Battery Pack
1-1：Push the battery Unlock button as below;
1-2：Push the battery Release button as below, then slide the battery pack out of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S9N-0366200-SB3 1

GX620&MS-1651 Disassemble SOP
■ 2、BOTTOM DOOR ASSY
2-1：Remove 2pcs M2.5*5mm Screws;
Note：Screw driver torque is 2.0~2.5kgf.cm
2-2：Remove Bottom Door Assy as below;

GX620&MS-1651 Disassemble SOP
2-3：Remove SIM Card Door as below;
NO. Part Name Part No. Qty
1Screw E43-1255001-H29 2
2 SIM CARD DOOR E2P-6510511-Y31 1
2BOTTOM DOOR ASSY 307-651J411-Y31 1

GX620&MS-1651 Disassemble SOP
■ 3、THERMAL-KIT And CPU Module
3-1：Remove 7pcs SPING Screws, Then Disconnect CPU Fan sink Cable;
Note：Screw driver torque is 2.0~2.5kgf.cm
6
5
2
1
3
7
4
3-2：Remove CPU Fan sink;
NO. Part Name Part No. Qty
1 CPU FANSINK E32-0900531-F05 1

GX620&MS-1651 Disassemble SOP
3-3：Open CPU slot as below;
3-4：Remove CPU Module;
NO. Part Name Part No. Qty
1 CPU Module A09-2520106-I06 1

GX620&MS-1651 Disassemble SOP
3-5：Remove 2pcs M2.5*5mm Screws;
Note：Screw driver torque is 2.5~3.0kgf.cm
3-6：Remove VGA Card Module;
NO. Part Name Part No. Qty
1 VGA CARD Module 602-V114-06S 1
2 Screw E43-1255001-H29 2

GX620&MS-1651 Disassemble SOP
■ 4、RAM、WLAN And TUNER Module
4-1：Push RAM Slot Fastener as below;
4-2：Remove RAM Module;
NO. Part Name Part No. Qty
1 RAM Module S7C-S347701-T10 2

GX620&MS-1651 Disassemble SOP
4-3：Remove WLAN Card Antenna, Then remove 1pcs M2*3mm Screw;
Note：Screw driver torque is 1.8~2.2kgf.cm
4-4：Remove WLAN Card Module;
NO. Part Name Part No. Qty
1 WLAN CARD Module S57-0800180-I06 1
2 Screw E43-1203003-H29 1

GX620&MS-1651 Disassemble SOP
4-5：Remove Tuner Antenna, Then remove 1pcs M2*3mm Screw;
Note：Screw driver torque is 1.8~2.2kgf.cm
4-6：Remove Tuner Module;
NO. Part Name Part No. Qty
1 TUNER Module S36-0000610-K45 1
2 Screw E43-1203003-H29 1

GX620&MS-1651 Disassemble SOP
■ 5、HDD Module ASSY
5-1：Remove 2pcs M2.5*5mm Screws Then remove HDD Door Assy as below;
Note：Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1Screw E43-1255001-H29 2
2HDD DOOR ASSY 307-651K411-Y31 1

GX620&MS-1651 Disassemble SOP
5-2：Remove HDD Module as below;
NO. Part Name Part No. Qty
1 Screw E43-1255001-H29 1

GX620&MS-1651 Disassemble SOP
5-3：Remove 2pcs M3*3.5mm Screws Then remove HDD Bracket as below;
Note：Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1Screw E43-1303501-H29 2
2HDD Bracket 307-6510111-Y28 1
3 HDD MODULE ASSY S71-2425504-F06 1

GX620&MS-1651 Disassemble SOP
■ 6、ODD Module ASSY
6-1：Remove 1pcs M2.5*5mm Screw Then remove ODD Module Assy as below;
Note：Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255001-H29 1

GX620&MS-1651 Disassemble SOP
6-2：Remove ODD Bezel as below;
NO. Part Name Part No. Qty
1 ODD Bezel E2P-651F211-Y31 1

GX620&MS-1651 Disassemble SOP
6-3：Remove 2pcs M2*3mm Screws Then remove ODD Bracket as below;
Note：Screw driver torque is 1.5~1.8kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-H29 2
2 ODD Bracket E2M-6510211-Y28 1

GX620&MS-1651 Disassemble SOP
■ 7、HINGE COVER ASSY
7-1：Push Fastener as below;

GX620&MS-1651 Disassemble SOP
7-2：Remove Hinge Cover as below;
NO. Part Name Part No. Qty
1 HINGE COVER 307-651E111-Y31 1

GX620&MS-1651 Disassemble SOP
7-3：Remove Hinge Cover Cable as below;
NO. Part Name Part No. Qty
1 POWER BOARD 607-1651B-C10 1

GX620&MS-1651 Disassemble SOP
7-4：Remove Cap Sensor Board as below;
NO. Part Name Part No. Qty
1 Cap Sensor Board 607-1651D-C10 1