MTB Cameras MTB-7400Q User manual

To reduce the risk of electric shock do not remove cover(or back)
No user serviceable parts inside. Refer servicing to qualified service personnel.
Design and specification are subject to change without notice.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
The lightning flash with arrowhead symbol,within an equilateral
triangle,is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
USER GUIDE
7" Wide TFT LCD Color Quad System
MTB-7400Q

-1-
Contents
CAMERA
SUN SHIELD WITH PROTECTION RUBBER (PATENT PENDING)
MONITOR
ACCESSORIES
STAND BRACKET KIT / SUCTION CUP KIT (OPTIONAL)
BUILT- IN REMOTE RECEIVER
BUILT- IN SPEAKER (1W)
RUBBER TOUCH NEUTRAL BLACK
AUTOMATIC SCREEN-ON (SIGNAL FROM "R"GEAR)
NOR./ MIR.& UP / DOWN IMAGE REVERSING
SHUTTER CAMERA / REAR VIEW CAMERA
SIDE VIEW CAMERA / HEATER CAMERA
WIDE SCREEN(16:9)
181(W) x 122 (H) x 24(D)mm (7.13x4.8x0.94 Inch)
DC 10V ~30V(Freevoltage)
POWER & CAMERA INPUT CABLE /
WATERPROOF / SUN SHIELD / IR SENSOR / NORMAL/MIRROR / HEATER (OPTIONAL)
DIMMER
REMOTE CONTROL
HOUSING
RESOLUTION
DISPLAY MODE
4 CAMERAS INPUT
SCREEN MODE
BRIGHTNESS
AUDIO OUTPUT
DIMENSION
POWER SOURCE
CAR REAR VIEW
SIZE
SPECIFICATION
BUILT- IN CDS SENSOR Automatic/Manual
1440 (W) x 234(H) Pixels
500 cd / m
OPERATING TEMP.
WEIGHT
-30 C ~ 85 C / -22 F ~ +185 F
STORAGING TEMP.
-20 C ~ 70 C / - 4 F ~ +158 F
450 (g)
VIEW ANGLE TOP: 40 BOTTOM: 60 LEFT: 60 RIGHT:60
2
°
°
°°
°
°
°°
-2-
Checking the main unit and supplied accessories
II
Features / Technical Specications
I
MTB-7400Q (QUAD MONITOR)
Operations
III 4-14
Checking the main unit and supplied accessories
II 2-3
Features / Technical Specications
I1
Using MTB-7400Q in the car
IV 16
SystemWiring
VI 16
Sun Shield
V17
MTB-80 Rear View Camera
VII 19
Xw
zwsp{
jhUzls
tlu|
kpt
}vs|tlG
}vs|tlG
jGz
Y
Z
[
]
^
_
\
X
Y]^
_Z
[\
GOP
OP
°°° °

-3-
z h
Power & Camera
Input Cable
Stand Bracket Kit
Rubber Sun Shield
User’s Guide
-4-
- If the Menu Key is pressed at the POWER ON mode, the OSD appears
in the monitor and the selected letters on OSD is classified in a different color.
-If pressing of the Menu Key is repeated in OSD state, the display
is circled in regular sequence of FUNCTION PICTURE NOR / MIR Clear of OSD.
the sequence will be as below without the CAMERA OSD.
FUNCTION PICTURE Clear of OSD.
- When POWER OFF (which means STANDBY state), the LED lights
in RED color.
- When POWER OFF, the R gear and the WINKERS (Left / Right) and
the TACHOMETER make that the linked each camera operates for displaying
its field of view on the monitor.
- After POWER ON, the LED in RED color is turned off and all
LEDs light in GREEN color.
- After POWER ON, the LAST CHANNEL saved from its last operation
is displayed on the monitor.
set-up (Factory Default).
- DIRECT POWER ON Subject To LAST POWER SAVE Mode:
* After starting up the car engine, the monitor turns on automatically
at the same time and the monitor starts displaying of the views from the
(1) If the car engine had been turned off at the POWER ON state of monitor,
the LAST POWER SAVE mode is ON (Factory Recommendation).
(2) If the car engine had been turned off after the POWER OFF of monitor,
the LAST POWER SAVE mode is OFF.
cameras if the LAST POWER SAVE mode is ON.
Operations
III
Accessories
1Power Key
2Menu Key
AMenu Control Keys
FUNCTION
LANGUAGE ENGLISH
DIRECTION
DIMMER
RESET ENTER
SYSTEM 0/180
AUTO/OFF
NTSC/PAL
PICTURE
CONTRAST
BRIGHT
COLOR
TINT
50 (0-100)
50 (0-100)
50 (0-100)
50 (0-100)
NOR/MIR
NOR/MIR
NOR/MIR
Heavy Duty Bracket Kit
NOR / MIR
CA1
CA2
CA3
CA4
NOR/MIR
NOR/MIR
NOR/MIR
NOR/MIR

-5-
50 VOLUME
[UGGjG|GVGkGr
- The brightness is adjusted manually at the POWER ON mode,
if DIMMER is selected in OSD set-up.
Pressing of DIMMER Key in this condition makes the change
of brightness responding on every manual operation of the Key.
- If pressing of the QUAD Key is repeated at the POWER ON mode, the display
is revolved in sequence of SPLIT PIP TRIPLE QUAD.
- In OSD state, this QUAD Key is in use of moving a cursor to
downward as well.
- If pressing of the CA.SEL Key is repeated at the POWER ON mode,
the CHANNEL is changed in regular sequence of
CH1 CH2 CH3 CH4
- In OSD state, pressing of these VOLUME Up / Down KEYS makes
the selected function to be adjusted and changed its status to new setup.
- Pressing of these VOLUME Up / Down KEYS at POWER ON mode makes
that the audio volume of the monitor is increased and/or decreased.
VOLUME Down KEY: To decrease the VOLUME
VOLUME Up KEY: To increase the VOLUME
Adjustable volume range from 0 to 100 (0 ~ 100)
Factory Default: 50
Language : 6 Languages
ENGLISH, GERMAN, FRENCH, ITALIAN,
SPANISH, DUTCH
- Locate the cursor at LANGUAGE by
CHANNEL and/or QUAD keys.
- Select the desired language by VOLUME Up/Down Keys.
- Factory default is ENGLISH.
-6-
SYSTEM
- Locate the cursor at SYSTEM by SPLIT and/or CA.SEL Keys.
- Select the proper system in your region by VOLUME Up/Down Keys.
- Factory default is PAL.
DIRECTION
- Locate the cursor at DIRECTION by SPLIT and/or CA.SEL Keys.
- Select the desired direction by VOLUME Up/Down Keys.
- 0 : Normal Screen (Factory Default)
- 180 : Shifted Screen to 180°reversely.
DIMMER SELECT KEY
- Locate the cursor at SELECT KEY by SPLIT and/or CA.SEL Keys.
- Select DIM by VOLUME Up/Down Keys.
- DIM : Release AUTO DIMMER and adjust the brightness manually by
pressing of DIMMER Key.
3DIMMER Key
4SPLIT(Up) Key
5CA.SEL(down) Key
6VOLUME Up / Down Key
1FUNCTION
BHow to set up the functions of the Menu on OSD
FUNCTION
LANGUAGE ENGLISH
DIRECTION
DIMMER AUTO/OFF
RESET ENTER
SYSTEM 0/180 NTSC/PAL
7
.

-7-
CONTRAST
- Display PICTURE set-up Screen by pressing the MENU Key twice
and locate the cursor at CONTRAST by SPLITand/or CA,SEL Keys.
- Adjust the Contrast by the Volume Up/Down Keys.
0 ~ 100 / 50 : Factory Default
BRIGHTNESS
- After locating the cursor at BRIGHT by SPLITand/or CA.SEL Keys,
adjust the Brightness by the Volume Up/Down Keys.
0 ~ 100 / 50 : Factory Default
COLOR
- After locating the cursor at COLOR by SPLIT and/or CA.SEL Keys,
adjust the Color by the Volume Up/Down Keys.
0 ~ 100 / 50 : Factory Default
TINT
- After locating the cursor at TINT by SPLIT and/or CA.SEL Keys,
adjust the Tint by the Volume Up/Down Keys.
0 ~100 / 50 : Factory Default
-8-
CAMERA1
- Display NOR/MIR set-up Screen by pressing the MENU Key 9 times
and locate the cursor at CA1 by SPLIT and/or CA.SEL Keys.
- Select the desired viewing mode between NOR and MIR by Volume Up/Down Keys.
- NOR : Normal Image / Factory Default
MIR : Mirror Image
(Symmetrically Reversed Image of Left & Right against Normal Image)
CAMERA2
- After locating the cursor at CA2 by SPLIT and/or CA.SEL Keys,
select the desired viewing mode between NOR and MIR by Volume
Up/Down Keys.
- NOR : Normal Image / Factory Default
MIR : Mirror Image
(Symmetrically Reversed Image of Left & Right against Normal Image)
CAMERA3
- After locating the cursor at CA3 by SPLIT and/or CA.SEL Keys,
select the desired viewing mode between NOR and MIR by Volume Up/Down Keys.
- NOR : Normal Image / Factory Default
MIR : Mirror Image
(Symmetrically Reversed Image of Left & Right against Normal Image)
CAMERA4
- After locating the cursor at CA4 by SPLIT and/or CA.SEL Keys,
select the desired viewing mode between NOR and MIR by Volume Up/Down Keys.
- NOR : Normal Image / Factory Default
MIR : Mirror Image
(Symmetrically Reversed Image of Left & Right against Normal Image)
2PICTURE 3NOR / MIR
PICTURE
CONTRAST
BRIGHT
COLOR
TINT
50 (0-100)
50 (0-100)
50 (0-100)
50 (0-100)
NOR / MIR
CA1
CA2
CA3
CA4
NOR/MIR
NOR/MIR
NOR/MIR
NOR/MIR

-9- -10-
TRI 1
- Display TRIGGER set-up Screen by pressing the MENU Key 9 times
and locate the cursor at TRI 1 by SPLITand/or CA.SEL Keys.
- Select the desired view mode among full screen of CA1~4 and SPLIT,
PIP, TRIPLE & QUAD view mode by Volume Up/Down Keys.
- Factory Default : Full Screen of CA1
TRI 2
- After locating the cursor at TRI 2 by SPLITand/or CA.SEL Keys,
select the desired view mode among full screen of CA1~4 and
SPLIT, PIP, TRIPLE & QUAD view mode by Volume Up/Down Keys.
- Factory Default : Full Screen of CA2
TRI 3
- After locating the cursor at TRI 3 by SPLITand/or CA.SEL Keys,
select the desired view mode among full screen of CA1~4 and
SPLIT, PIP, TRIPLE & QUAD view mode by Volume Up/Down Keys.
- Factory Default : Full Screen of CA3
4TRIGGER / TIME
TRRIGGER
TRI1
TRI2
TRI3
(CA1~QUAD)
(CA1~QUAD)
(CA1~QUAD)
CA1
CA2
CA3
TRI1
TRI2
TRI3
(0~9) 3
(0~9) 3
(0~9) 3
TIME
TIME
TIME
TRI 1 TIME
- After locating the cursor at TRI 1 TIME by SPLIT and/or CA.SEL Keys,
select the desired delaying time for the selected viewing mode among
0 ~ 9 seconds by Volume Up/Down Keys.
- Factory Default : 0 second
TRI 2 TIME
- After locating the cursor at TRI 2 TIME by SPLIT and/or CA.SEL Keys,
select the desired delaying time for the selected viewing mode among
0 ~ 9 seconds by Volume Up/Down Keys.
- Factory Default : 3 seconds
TRI 3 TIME
- After locating the cursor at TRI 3 TIME by SPLIT and/or CA.SEL Keys,
select the desired delaying time for the selected viewing mode among
0 ~ 9 seconds by Volume Up/Down Keys.
- Factory Default : 3 seconds
TIME

-11- -12-
SPLIT
- Display SPLIT set-up Screen by pressing the MENU Key 9 times
and locate the cursor at SPLIT by SPLITand/or CA.SEL Keys.
SOURCE1
- After locating the cursor at SOURCE1 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’
by Volume Up/Down Keys.
SOURCE2
- After locating the cursor at SOURCE2 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’
by Volume Up/Down Keys.
AUDIO
- After locating the cursor atAUDIO by SPLIT and/or CA.SEL Keys,
select the desired Camera to hear of the AUDIO among the cameras
‘CA1 ~ CA4’ by Volume Up/Down Keys.
- Factory Default : CA1
SPLIT1
SOURCE 1
SOURCE 2
AUDIO CA1 (CA1~CA4)
CA1 (CA1~CA4)
CA2 (CA1~CA4)
6SPLIT1 / SPLIT2
TACHO GRAPH
TACHO SW
TACHO
TACHO TIME
FREQUENCY
ON/OFF
67 HZ (10 ~ 101HZ)
CA1 (CA1~QUAD)
0 ~ 9
5TACHO GRAPH
SPLIT2
SOURCE 1
SOURCE 2
AUDIO CA1 (CA1~CA4)
CA1 (CA1~CA4)
CA2 (CA1~CA4)
TACHO...SW
TACHO CA1
- After locating the cursor at TACHO by SPLIT and/or CA.SEL Keys,
select the desired Tacho to view among the cameras ‘CA1 ~ QUAD’
by Volume Up/Down Keys.
TACHO TIME
- After locating the cursor at TACHO TIME by SPLIT and/or CA.SEL Keys,
select the desired Tacho Time to view among the cameras ‘0 ~ 9’
by Volume Up/Down Keys.
FREQUENCY
- After locating the cursor atFREQUENCY by SPLIT and/or CA.SEL Keys,
select the desired Frequency to among the cameras
‘10HZ ~ 101HZ’ by Volume Up/Down Keys.
- Factory Default : 67HZ
- Display TACHO set-up Screen by pressing the MENU Key 9 times
and locate the cursor at TACHO by SPLIT and/or CA.SEL Keys.

-13-
PIP
- Display PIP set-up Screen by pressing the MENU Key 9 times
and locate the cursor at PIP by SPLITand/or CA.SEL Keys.
SOURCE1
- After locating the cursor at SOURCE1 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
SOURCE2
- After locating the cursor at SOURCE2 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
SOURCE3
- After locating the cursor at SOURCE3 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
AUDIO
- After locating the cursor at AUDIO by SPLIT and/or CA.SEL Keys,
select the desired Camera to hear of the AUDIO among the cameras
‘CA1 ~ CA4’ by Volume Up/Down Keys.
- Factory Default : CA1
-14-
TRIPLE
- Display TRIPLE set-up Screen by pressing the MENU Key 9 times
and locate the cursor at TRIPLE by SPLIT and/or CA.SEL Keys.
SOURCE1
- After locating the cursor at SOURCE1 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
SOURCE2
- After locating the cursor at SOURCE2 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
SOURCE3
- After locating the cursor at SOURCE3 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
AUDIO
- After locating the cursor at AUDIO by CHANNEL and/or QUAD Keys,
select the desired Camera to hear of the AUDIO among the cameras
‘CA1 ~ CA4’by Volume Up/Down Keys.
- Factory Default : CA1
PIP
SOURCE 1
SOURCE 2 CA1 (CA1~CA4)
CA2 (CA1~CA4)
SOURCE 3
AUDIO
CA3 (CA1~CA4)
CA1 (CA1~CA4)
TRIPLE
SOURCE 1
SOURCE 2 CA1 (CA1~CA4)
CA2 (CA1~CA4)
SOURCE 3
AUDIO CA3 (CA1~CA4) CA1 (CA1~CA4)
8TRIPLE
7PIP

-15-
QUAD
- Display QUAD set-up Screen by pressing the MENU Key 9 times
and locate the cursor at QUAD by SPLIT and/or CA.SEL Keys.
SOURCE1
- After locating the cursor at SOURCE1 by SPLIT and/or
select the desired Camera to view among the
Volume Up/Down Keys.
SOURCE2
- After locating the cursor at SOURCE2 by SPLIT and/or
select the desired Camera to view among the
Volume Up/Down Keys.
SOURCE3
- After locating the cursor at SOURCE3 by SPLIT and/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
SOURCE4
- After locating the cursor at SOURCE4 by SPLITand/or CA.SEL Keys,
select the desired Camera to view among the cameras ‘CA1 ~ CA4’by
Volume Up/Down Keys.
AUDIO
- After locating the cursor at AUDIO by SPLIT and/or CA.SEL Keys,
select the desired Camera to hear of the AUDIO among the cameras
‘CA1 ~ CA4’by Volume Up/Down Keys.
- Factory Default : CA1
-16-
APPLICATION DISPLAY
SPLIT 1
S1 S2
S1
S2
S3
S2 S3
S1
S1 S2
S3 S4
TRIPLE
PIP
QUAD FULL SCREEN
QUAD
SOURCE 1
SOURCE 2 CA1 (CA1~CA4)
CA2 (CA1~CA4)
SOURCE 3
SOURCE 4
AUDIO
CA3 (CA1~CA4)
CA4 (CA1~CA4)
CA1 (CA1~CA4)
9QUAD
SPLIT 2
S1
S2
CA.SEL Keys,
Cameras ‘CA1 ~ CA4’by
CA.SEL Keys,
Cameras ‘CA1 ~ CA4’by
CAM / MODUS
CA 1
CA 2 ON / OFF
CA 3
CA 4
SPLIT1
10 CAM / MODUS
SPLIT2
PIP
TRIPLE
QUAD
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
ON / OFF
CAM / MODUS
- Display CAM / MODUS set-up Screen by pressing the
and locate the cursor at CAM / MODUS
MENU Key 9 times
by SPLIT and/or CA.SEL Keys.
- After locating the cursor at CA1~QUAD by SPLIT and/or
select the desired CAM/MODUS to view among
by Volume Up/Down Keys.
‘CA1 ~ QUAD’
CA.SEL Keys,
among the cameras

-17-
By setting up MTB-7400Q with the Sun Shield which has
the rubber guide for protection,
the MTB-7400Q will be shielded off the direct sunlight.
The Sun Shield will offer visual comfort for driving and
will make driving safer
&
more comfortable.
Also, the rubber Sun Shield Will give the drivers a great
help to protect them from injury.
After connecting power to the unit through the Cigarette adaptor, press
[Power button] on the main unit or on the Remote Control to power on.
Set up MTB-7400Q with Stand Bracket Kit and fix the Stand Bracket Kit
on the dashboard of the car.
-18-
W
E
I
V
K
CA
BW
E
I
V
E
DIS
FRONT VIEW
Tachometer Trigger (Trigger 3) should be
wired with the desired camera trigger wire
among Trigger 1 ~ 3 wires, for which the
camera reacts on speed of the vehicle.
SIGNAL IN (FROM LAMP)
EXTENSION CABLE
SIDE VIEW CAMERA-L
REAR VIEW CAMERA
SIDE VIEW CAMERA-R
Using MTB-7400Q in the car
IV
Sun Shield
V
For using MTB-7400Q on the dashboard
System Wiring
VI
CAMERA CONNECTION
1
53
4
2
HEATER(OPTIONAL)
DC12V POWER
VIDEO OUTPUT
DESCRIPTION
3
GROUND
5
4
AUDIO
PIN NO.
2
1
Fasten the bolt
to fix the main unit
to Stand Bracket Kit.
Fixon the dashbord
in the car
ACC 12~32V Trigger 3/Tacho
12~30V Trigger 1 12~30V
Ground Trigger 2
12~30V

-20-
-19-
Attach the supplied mounting bracket to vehicle.
Adjust the angle of the camera and fasten the screws firmly.
Waterproof Aluminium Diecasted Low Illumination Color CCD Camera.
Mirror & Normal Image Views
MOUNTING
BRACKET
M4X10 WRENCH
BOLTS 4EA (SEMS)
M4 NYLON NUTS
4EA
M5X15 TP.Or MACHINE
SCREWS 4EA
CAMERA
SUN SHIELD
MTB-10C Rear View Camera
VII
1Features & Installation
2Specifications
CAMERA CONNECTION
1
53
4
2
HEATER(OPTIONAL)
DC12V POWER
VIDEO OUTPUT
DESCRIPTION
3
GROUND
5
4
AUDIO
PIN NO.
2
1
IMAGE SENSOR
EFFECTIVE PIXELS
RESOLUTION
SYNCHRONIZING SYSTEM
VIDEO OUTPUT
AUDIO INPUT
S/N RATIO
REQUIRED .ILLUMINATION
POWER SOURCE
FIELD OF VIEW / OPTION
OPERATING TEMPERATURE
DIMENSION
WEIGHT
ACCESSORIES
BEST NIGHT VIEW FEATURE
1/3" Sony Super HAD Color CCD
(Compatible with Sharp CCD)
NTSC : 270,000 Pixels / PAL : 320,000 Pixels
380 TV Lines
Internal
75 Ohms ,1.0Vp-p Composite.
High Sensitive C-Microphone
More than 48dB
0 Lux at F2.0 / f =2.45mm (LED ON)
DC 12V / Max. 150mA (LED ON)
-22°F ~ 140°F (-30°C ~ +60°C)
-58°F ~ 140°F (-50°C ~ +60°C) With Heater
69(W) X 42(H) X57(D) mm
2.7(W) X 1.65(H) X 2.2(D) inch
650g
65ft (20M) Waterproof cable (Option)
Sun Shield
Mounting Bracket and Screw Kits
20 degrees visible IR LED X 6ea
120° 130° 150°
OPERATING VOLTAGE RANGE DC 12V
4EA